Search NASA⌕ Search

Engineering topics

Cole, S. R.

Publications and source records attributed to Cole, S. R..

13 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Divergence study of a high-aspect ratio, forward-swept wing

An experimental wind-tunnel study to determine the divergence characteristics of a high-aspect ratio, forward-swept wing has been conducted in the NASA Langley Research Center (LaRC) Transonic Dynamics Tunnel (TDT). The rectangular wing used for this study had a panel aspect ratio of 9.16 (lambda = 0 deg.) and the sweep angle could be set at lambda = 0 deg., -15 deg., -30 deg., -45 deg., or -60 deg. A rectangular wing tip shape was tested at each of these sweep angles. In addition, a tip shape parallel to the freestream flow was tested for a wing sweep angle of lambda = -45 deg. The root of the wing was cantilever mounted to the wall of the wind tunnel. Divergence conditions were measured at M = 0.4 for each sweep angle and tip configuration tested. Subcritical response techniques were used to extrapolate to the divergence conditions during the wind-tunnel test. The primary objective of this test was to obtain data which could be used to verify for this configuration the divergence prediction capability of an aeroelastic analysis code. Subsonic lifting surface theory (kernel function) aerodynamics are utilized by this particular code. The analytical predictions of divergence were found to be significantly conservative at all forward sweep angles. At lambda = -45 deg., the analysis was 14 percent conservative. The effect of the two tip shapes on the divergence dynamic pressure was predicted accurately by the analysis. The divergence condition for the tip shape parallel to the flow occurred at a dynamic pressure 14 percent higher than the divergence condition with a rectangular tip shape.

Cole, S. R.↗
NASA NTRS1986

Divergence study of a high-aspect ratio, forward-swept wing

A study has been conducted in the NASA-Langley Transonic Dynamics wind tunnel to determine the divergence characteristics of a high aspect ratio forward swept wing of rectangular planform, for sweep angles of zero, -15, -30, -45, and -60 deg. In addition to a rectangular wingtip, a tip whose geometry lay parallel with the freestream flow was tested at a sweep angle of -45 deg. The primary objective was to obtain data that could be used to verify the divergence prediction capabilities of an aeroelastic analysis code employing kernel function aerodynamics. The analytical predictions of convergence were found to be conservative for all forward sweep angles, and the effect of the two tip shapes on divergence dynamic pressure were accurately predicted.

Cole, S. R.↗
NASA NTRS1985

Exploratory flutter test in a cryogenic wind tunnel

A model consisting of a rigid wing with an integral, flexible beam support that was cantilever mounted from the wall in the NASA LaRC 0.3-m transonic cryogenic tunnel was used in a flutter analysis study. The wing had a rectangular planform of aspect ratio 1.5 and a 64A010 airfoil. Various considerations and procedures for conducting flutter tests in a cryogenic wind tunnel were evaluated. Flutter onset conditions were established from extrapolated subcritical response measurements. A flutter boundary was determined at cryogenic temperatures over a Mach number M range from 0.5 to 0.9. Flutter was obtained at two different Reynolds numbers R at M = 0.5 (R = 4.4 and 18.4 x 10 to the 6th power) and at M = 0.8 (R = 5.0 and 10.4 x 10 to the 6th power). Flutter analyses using subsonic lifting surface (kernel function) aerodynamics were made over the range of test conditions. To evaluate the Reynolds number effects at M = 0.5 and 0.8, the experimental results were adjusted using analytical trends to account for differences in the model test temperatures and mass ratios. The adjusted experimental results indicate that increasing Reynolds number from 5.0 to 20.0 x 10 to the 6th power decreased the dynamic pressure by 4.0 to 6.5 percent at M = 0.5 and 0.8.

Cole, S. R.↗
NASA NTRS1985

Exploratory flutter test in a cryogenic wind tunnel

The feasibility of flutter testing in cryogenic wind tunnels is investigated experimentally in tests on a rigid solid-metal rectangular-planform aspect-ratio-1.5 NACA 64A010 wing model with an integral flexible beam support, cantilever mounted to the wall of the 0.3-m transonic cryogenic tunnel at NASA Langley, at Mach numbers M = 0.5 and 0.8 and Reynolds numbers Re = (4.09-18.16) x 10 to the 6th. Best results are obtained when the onset of flutter (predicted by the peak-hold subcritical-response technique of Sandford et al., 1975) is approached by adjusting stagnation pressure while keeping M and the stagnation temperature constant. The data are presented in graphs and tables and discussed. It is found that Re effects on flutter cannot be separated from mass-ratio and temperature effects for a single test model and must be interpreted from analytical trends, and that the effects detected by this procedure are so small (4.0-6.5 percent) as to fall within the scatter band of the subcritical-response predictions.

Cole, S. R.↗
NASA NTRS1983

Predictions of entry heating for lower surface of shuttle orbiter

A broad base of thermocouple and phase change paint data was assembled and correlated to the nominal design 14414.1 and proposed STS-1 (first flight of the space transportation system) entry trajectories. Averaged data from phase change paint tests compared favorably with thermocouple data for predicting heating rates. Laminar and turbulent radiation equilibrium heating rates were computed on the lower surface of the Shuttle orbiter for both trajectories, and the lower surface center line results were compared both with aerodynamic heating design data and with flight values from the STS-1 and STS-2 trajectories. The peak laminar heating values from the aerodynamic heating design data book were generally 40 to 60 percent higher than the laminar estimates of this study, except at the 55 percent location of maximum span where the design data book values were less than 10 percent higher. Estimates of both laminar and turbulent heating rates compared favorably with flight data.

Edwards, C. L. W.↗
NASA NTRS1981

Experimental research on structural dynamics and control

This report describes an apparatus at the NASA Langley Research Center for conducting research on dynamics and control of structural dynamics systems. The apparatus consists of a 3.66 m (12 ft.) long flexible beam to which are attached four electromagnetic actuators, nine noncontacting sensors to measure deflection of beam at various locations, and four strain gage type load cells one at each actuator attachment point. The important feature of the apparatus is that the actuators can be controlled and deflection and load sensor data can be processed in real time using the research centers CDC Cyber 175 computer system - thereby allowing research to be conducted on structural dynamics systems using advanced control laws. The facility is described in the report along with a detailed discussion of the actuators used.

Montgomery, R. C.↗
NASA NTRS1974

The synergistic effects of slip ring-brush design and materials

The design, fabrication, and subsequent testing of four power slip rings for synchronous orbit application are described. The synergistic effects of contact materials and slip ring-brush design are studied by means of frequent and simultaneous recording of friction, wear, and electrical noise. Data generated during the test period are presented along with post test analysis data.

Lewis, N. E.↗
NASA NTRS1974

Long-duration life tests of slip ring capsule assemblies for inertial guidance platforms

Eight slip ring capsules, each having 80 or 100 circuits, were operated for time periods ranging from 14,300 hours to 24,700 hours. The test mode simulated the motion of gimbal axes of the Saturn inertial guidance the platform in an organic free nitrogen environment. Computer-compiled noise data (approximately 45,000 recordings) were graphed as a function of test time and position within the capsules and as extreme probability distributions. Greater than ninety-nine percent of the noise measurements for the capsules with sufficient lubrication were less than 10 milliohms. Capsules with glass dielectrics did not perform significantly differently than those with filled epoxy dielectrics. The initial wear mode of prow formation was followed by rider wear. After 10 to the 8th power wipes, ring wear depth did not exceed the surface finish and the radial rider wear depth was less than 13 microns.

Cole, S. R.↗
NASA NTRS1973

Friction, wear, and noise of slip ring and brush contacts for synchronous satellite use.

A program is being conducted for testing of slip rings for synchronous orbit application. Instrumentation systems necessary for monitoring electrical noise, friction, and brush wear at atmospheric pressure and at less than 50 nanotorr have been developed. A multiplex scheme necessary for the simultaneous recording of brush displacement, friction, and electrical noise has also been developed. Composite brushes consisting of silver-molybdenum disulfide-graphite and silver-niobium diselenide-graphite have been employed on rings of coin silver and rhodium plate. Brush property measurements made included measurement of density, electrical resistivity, shear strength, and microstructure.

Lewis, N. E.↗
NASA NTRS1972

Inorganic glass ceramic slip rings

Prototypes of slip rings have been fabricated from ceramic glass, a material which is highly resistant to deterioration due to high temperature. Slip ring assemblies were not structurally damaged by mechanical tests and performed statisfactorily for 200 hours.

Glossbrenner, E. W.↗
NASA NTRS1972

Friction, wear and noise of slip ring and brush contacts for synchronous satellite use.

A program is being conducted for testing of slip rings for synchronous orbit application. Instrumentation systems necessary for monitoring electrical noise, friction, and brush wear at atmospheric pressure and at less than 50 ntorr have been developed. A multiplex scheme necessary for the simultaneous recording of brush displacement, friction, and electrical noise has also been developed. Composite brushes consisting of silver-molybdenum disulfide-graphite and silver-niobium diselenide-graphite have been employed on rings of coin silver and rhodium plate. Four contact combinations have been tested during an ambient condition run-in at 150 rpm and a humidity sequence at 0.1 rpm. The first six months of the two year vacuum test at 0.1 rpm have been completed. Electrical noise, friction and brush wear data recorded during these periods have been analyzed.

Lewis, N. E.↗