Engineering topics
Publications and source records attributed to Cole, T..
A prototype digital optical module has been constructed for use in conjuction with the AMANDA neutrino detector at the South Pole.
No abstract available
The properties of the alkali metal thermoelectric converter (AMTEC) are discussed together with those of an efficient AMTEC electrode. Three groups of electrodes were prepared and tested for their performance as AMTEC electrodes, including WPt-T3, WRh-B1, and WRh-B2. The best electrodes of both WPt and WRh types typically exhibited low porosity, and thickness greater than 0.8 micron, which indicated that transport in these electrodes does not occur by a purely free-molecular flow mode. The observed values of the exchange current were found to be within the range of those observed for oxide-free Mo electrodes under similar conditions.
New biphase metal electrodes for alkali metal thermoelectric converter (AMETEC) exhibit low electrical resistance, fast alkali metal transport, and good power densities and lifetime at operating temperatures from 1,100 to 1,160 K. Electrodes expected to last as long as 10,000 h in service without significant degradation. Made of two refractory metals, one forms strong bonds with sodium, other inert to sodium.
Columnar, porous, magnetron-sputtered molybdenum and tungsten films show optimum performance as alkali metal thermoelectric converter electrodes at thicknesses less than 1.0 micron when used with molybdenum or nickel current collector grids. Power densities of 0.40 W/sq cm for 0.5-micron molybdenum films at 1200 K and 0.35 W/sq cm for 0.5-micron tungsten films at 1180 K were obtained at electrode maturity after 40-90 h. Sheet resistances of magnetron sputter deposited films on sodium beta-double-prime-alumina solid electrolyte (BASE) substrates were found to increase very steeply as thickness is decreased below about 0.3-double-prime 0.4-micron. The ac impedance data for these electrodes have been interpreted in terms of contributions from the bulk BASE and the porous electrode/BASE interface. Voltage profiles of operating electrodes show that the total electrode area, of electrodes with thickness less than 2.0 microns, is not utilized efficiently unless a fairly fine (about 1 x 1 mm) current collector grid is employed.
Four electrode compositions have demonstrated power densities high enough to make practical alkali metal thermoelectric converter (AMTEC) systems feasible. These electrode compositions are very thin molybdenum, platinum/tungsten trilayer, rhodium/tungsten bilayer, and titanium nitride. These electrodes have produced stable maximum power densities of 0.4 to 0.8 W/sq cm at 1100-1250 K for 90 to 160 hours.
The Alkali Metal Thermoelectric Converter (AMTEC) is a direct energy conversion device, utilizing a high sodium vapor pressure or activity ratio across a beta-alumina solid electrolyte. Progress is reported on a long life, high power, porous electrode. Two electrode compositions were identified which have the potential for long life operation at power densities above 0.5 W/sq cm. Longer lifetime testing is being initiated. Successful optimization and demonstration of very long lifetimes for these electrodes will be a major step toward establishing the feasibility of AMTEC space power systems.
Voltammetry of partially oxidized porous molybdenum alkali metal thermoelectric converter (AMTEC) electrodes from about 600 to 1000 K revealed a series of redox processes within the AMTEC operational voltage range which can be used to establish the electronic and ionic conductivities of these electrodes. Improved estimates of the free energies of formation of Na2Mo3O6, NaMoO2, and Na3MoO4 are obtained. Evidence is provided for the slow corrosive attack by Na2MoO4 on molybdenum. The ionic conductivity of Na2MoO4 is found to be sufficiently large at temperatures of greater than 700 K to explain the observed electrochemical phenomena in addition to the enhanced sodium transport in AMTEC electrodes below the freezing point of Na2MoO4.
A model for chemical reactions in porous molybdenum electrodes is presented which is based on thermochemical and kinetic data, known sodium-molybdenum-oxygen chemistry, X-ray diffraction analysis of molybdenum and molybdenum oxide electrodes, and the electrochemical behavior of the cell. Enhanced sodium transport through the electrode in its optimum performance state is found to be due to the high sodium ion conductivity of molten Na2MoO4 in the pores, and the electrical conduction to the molybdenum matrix by Na2Mo3O6. The decline of electrode performance is shown to be due to a combination of loss mechanisms for the Na-Mo-O compounds including reduction at short circuit, disproportionation of Na2Mo3O6 at open circuit, and the evaporation of Na2MoO4 at elevated temperature. It is suggested that operation of the cell at moderate voltage of about 0.5 V corresponding to maximum power may be a more stable condition for the porous electrode than open-circuit stand or short-circuit, where degradation reactions are heightened.
Small modular alkali metal thermoelectric generator with no moving parts directly converts heat to electrical energy with efficiency of 20 to 40 percent. Unit uses closed regenerative electrochemical concentration cell based on sodium-ion conductor beta alumina.
Performance parameters of the Alkali Metal Thermoelectric Converter (AMTEC) for a 100 kW electric power system have been calculated at four technological levels assuming a heat pipe-cooled nuclear reactor heat source. The most advanced level considered would operate between 1180 K converter temperature and 711 K radiator temperature at 16 percent efficiency, and would weigh 1850 kg with a radiator area of 43 sq m. In addition, electrode research studies for the AMTEC systems have been conducted utilizing an experimental test cell of Bankston et al. (1983) and Mo and several Mo-Ti electrodes. It was found that the Mo-Ti electrodes offered no improvement in lifetime characteristics over the pure Mo electrodes, however, oxygen treatment of a degraded Mo electrode restored its specific power output to 90 percent of its original specific power and maintained this level for 60 hr, thus offering a potential for lifetime stability.
Previously cited in issue 15, p. 2361, Accession no. A82-31876
The alkali metal thermoelectric converter (AMTEC) is a device for the direct conversion of heat to electrical energy. The sodium ion conductor beta-double prime-alumina is used to form a high-temperature regenerative concentration cell for elemental sodium. An AMTEC of mature design should have an efficiency of 20 to 40 percent, a power density of 0.5 kilowatt per kilogram or more, no moving parts, low maintenance requirements, high durability, and efficiency independent of size. It should be usable with high-temperature combustion, nuclear, or solar heat sources. Experiments have demonstrated the feasibility of the AMTEC and confirmed the theoretical analysis of the device. A wide range of applications from aerospace power to utility power plants appears possible.
A thermally regenerative electrochemical device for the direct conversion of heat to electrical energy, the alkali metal thermoelectric converter (AMTEC), is characterized by potential efficiencies on the order of 15-40% and possesses no moving parts, making it a candidate for space power system applications. Device conversion efficiency is projected on the basis of experimental voltage vs current curves exhibiting power densities of 0.7 W/sq cm and measured electrode efficiencies of up to 40%. Preliminary radiative heat transfer measurements presented may be used in an investigation of methods for the reduction of AMTEC parasitic radiation losses. AMTEC assumes heat input and rejection temperatures of 900-1300 K and 400-800 K, respectively. The working fluid is liquid sodium, and the porous electrode employed is of molybdenum.