Search NASA⌕ Search

Engineering topics

Collett, Timothy S.

Publications and source records attributed to Collett, Timothy S..

12 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

UT-GOM2-2 Preliminary Report: Terrebonne Basin Northern Gulf of Mexico, 30 July-28 September 2023

In the summer and fall of 2023, the Gulf of Mexico Deepwater Hydrate Coring Expedition (UT-GOM2-2) drilled, cored, made downhole measurements, and analyzed samples from the seafloor to the base of the gas hydrate stability zone in one location (Site H, WR313) in the Terrebonne basin, deepwater Gulf of Mexico. Analyses of data and samples from the expedition will inform biological, geochemical, and geomechanical models to constrain the role of gas hydrates in the carbon cycle and the potential for gas hydrates as an energy resource. Pressure and conventional cores were collected continuously to a depth of 155.1 meters below the seafloor (mbsf). At deeper depths, cores were taken periodically from hydrate-bearing sands and their bounding muds to a total depth of 861.3 mbsf. 162.6 m of conventional core and 54.8 m of pressure core were obtained. Twelve temperature measurements were made between 27.1 and 144.5 mbsf to determine the geothermal gradient. At the seafloor, more than 4 m of sandy silt of unknown origin was encountered. Beneath this sand, to a depth of ~200 mbsf, the section was composed of interbedded mud and biogenic carbonate ooze. The biogenic ooze correlated to low density and high porosity intervals observed in the previously acquired logging while drilling (LWD) data and as measured. Calcareous nannofossil biostratigraphy constrains the entire record to the Pleistocene (< 0.91 million years) with a pronounced increase in sedimentation rate with depth. Beneath 200 mbsf, the section was predominantly composed of mud with two thicker, hydrate-bearing coarse-grained intervals, which are commonly known as the Blue and Orange sands. The dissolved gas concentration was quantified from pressure cores. In the shallow section, dissolved methane concentration increased below the sulfate-methane transition zone (SMTZ) and reaches saturation (the limit of solubility for methane) at 147 mbsf. Gas expansion was very common in conventional and depressurized pressure (conventionalized) cores below the SMTZ. At deeper depths, the methane concentration within muds bounding the Blue and Orange reservoirs was generally found to be less than saturation. The dissolved and hydrate gas composition is consistent with a microbial source, containing greater than 99.99% methane and only trace concentrations of ethane, propane, and butane. The methane to ethane ratio (C 1 /C 2 ) and the methane to ethane plus propane (C 1 /(C 2 +C 3 )) decrease with depth down to at least 678 mbsf, mainly driven by the increase in ethane with depth. It is unclear if this trend continues through the Orange sand interval. The δ 13 C isotopic signature of methane ranges between -69.9 and -78.5 ‰ Vienna Pee Dee Belemnite (VPDB). Pressure core recovery of all sandy intervals was poor. However, pressure core logs of the Orange sand show intervals of low density and high velocity, which are indicative of high hydrate saturation. One core from within the Orange sand was composed of interbedded graded sandy silt and mud. The sandy silts from this core are composed of mainly quartz and feldspar with some lithics. Most of the recovered pressure core samples are maintained at near in-situ pressure and temperature (within the hydrate stability field) at the University of Texas Pressure Core Center awaiting analysis. In the shallow section, samples will be used to determine the flux of organic carbon through the basin system, find the rate at which that carbon was consumed, and understand the microbial population responsible for these processes. In the deeper section, samples from in and around the hydrate reservoirs will be used to determine the petrophysical properties of the reservoir and bounding seals in these systems.

03 NATURAL GAS↗
DOE OSTI2024

3-D Geological Modeling for Numerical Flow Simulation Studies of Gas Hydrate Reservoirs at the Kuparuk State 7-11-12 Pad in the Prudhoe Bay Unit on the Alaska North Slope

Accurate reservoir evaluation requires reliable three-dimensional (3-D) geological models. Here, this study conducted 3-D geological modeling for numerical flow simulation of the B1 sand gas hydrate reservoir at the Kuparuk State 7-11-12 pad, Prudhoe Bay Unit, Alaska North Slope. The model integrates well logs, core, and seismic data to address spatial heterogeneity in geological structures and reservoir properties. Two modeling types were performed: structural framework modeling and petrophysical property modeling. For structural framework modeling, seismic data and well log markers were used to reproduce subsurface structures characterized by a normal fault system. A volume-based modeling algorithm and stair-stepping grid were applied. The resulting 3-D model comprised 2,640,000 grid cells across 264 layers, including seven fault grids. For petrophysical property modeling, total porosity was initially modeled using sequential Gaussian simulation with collocated cokriging. To reproduce the upward coarsening of the B1 sand, upscaled log-derived total porosity and a three-dimensional (3-D) trend depicting total porosity variation were used as primary and secondary data, respectively. Gas hydrate saturation distribution was modeled similarly, with secondary data from estimated porosity distribution and seismic-derived acoustic impedance map enhancing accuracy. Results indicate higher gas hydrate saturation in the upper part of the B1 sand and areas with higher acoustic impedance. Intrinsic permeability was modeled from the total porosity and clay-bound water volume, and effective permeability was derived from the gas hydrate saturation and intrinsic permeability distributions based on the “Tokyo model”. Effective permeability distributions were influenced by the total porosity, gas hydrate saturation, and intrinsic permeability. Within the same layer, higher gas hydrate saturation leads to decreased effective permeability. In total, 100 sets of multiple scenarios were prepared, providing input data for dynamic flow simulations to evaluate the effects of lateral heterogeneity in reservoir properties and the hydraulic characteristics of faults on production behavior for preassessment before the long-term production test.

58 GEOSCIENCES↗
DOE OSTI2023

Machine Learning Application to Assess Occurrence and Saturations of Methane Hydrate in Marine Deposits Offshore India

Artificial Neural Networks (ANN) were used to assess methane hydrate occurrence and saturation in marine sediments offshore India. The ANN analysis classifies the gas hydrate occurrence into three types: methane hydrate in pore space, methane hydrate in fractures, or no methane hydrate. Further, predicted saturation characterizes the volume of gas hydrate with respect to the available void volume. Log data collected at six wells, which were drilled during the India National Gas Hydrate Program Expedition 02 (NGHP-02), provided a combination of well log measurements that were used as input for machine learning (ML) models. Well log measurements included density, porosity, electrical resistivity, natural gamma radiation, and acoustic wave velocity. Combinations of well logs used in the ML models provide good overall balanced accuracy (0.79 to 0.86) for the prediction of the gas hydrate occurrence and good accuracy (0.68 to 0.92) for methane hydrate saturation prediction in the marine accumulations against reference data. The accuracy scores indicate that the ML models can successfully predict reservoir characteristics for marine methane hydrate deposits. In conclusion, the results indicate that the ML models can either augment physics-driven methods for assessing the occurrence and saturation of methane hydrate deposits or serve as an independent predictive tool for those characteristics.

58 GEOSCIENCES↗
DOE OSTI2021

Emerging Issues in the Development of Geologic Models for Gas Hydrate Numerical Simulation

The numerical simulation of gas hydrate reservoirs has evolved greatly in recent years. Scientific and industrial drilling programs have acquired detailed characterization data from gas hydrate systems in Alaska, Japan, India, Korea, China, and the Gulf of Mexico. These data provide invaluable calibration points that serve to ground-truth hydrate reservoir modeling efforts.

Boswell, Ray↗
DOE OSTI2020

Petrophysical and geomechanical properties of gas hydrate-bearing sediments recovered from Alaska North Slope 2018 Hydrate-01 Stratigraphic Test Well

Knowledge of petrophysical and geomechanical properties of gas hydrate-bearing sediments are essential for predicting reservoir response due to gas production from gas hydrate reservoirs. That information will be critical parameters for designing production well completion such as specification of depressurization pump, water storage tank, and mesh size of sand screen. In December 2018, Stratigraphic Test Well Hydrate-01 was drilled in the western part of the Prudhoe Bay Unit, Alaska North Slope as part of the technical planning effort for a future long-term production test by collaborative team of DOE/NETL, USGS, and MH21-S (Boswell et al., 2020, Collett et al., 2020, Okinaka et al., 2020). Data set of logging-while-drilling (LWD) were acquired (Haines et al., 2020, Suzuki et al., 2019) and core sampling depth was determined on-site.Side-wall pressure coring was conducted to recover gas hydrate-bearing sediments from two reservoir sections named Unit-B and Unit-D. A total of 34 cores were successfully recovered by 5 runs of a wire-line deployed pressure corer (CoreVault® System - Halliburton). Core analysis scheme of this project are shown in Figure 1. All cores were quenched in liquid nitrogen while at high pressure in the laboratory of Stratum Reservoir, LLC. at Anchorage (Figure 1, a)). And the cores were removed from the pressure corer autoclave with temperature support of dry ice and stored under liquid nitrogen at atmospheric pressure. 19 damaged cores were processed to index property measurements directly such as grain size, grain density. 4 of another 17 cores were depressurized and trimmed for making a plug to analyze petrophysical properties of host sediments. Unsteady-state permeability test was conducted to obtain relative water permeability to gas and core scale NMR T2 distribution measurement was performed for evaluating pore size distribution at Houston (Figure 1, b)). Remained high quality 13 cores were preserved with gas hydrate for advanced laboratory analysis. National Institute of Advanced Industrial Science and Technology, as a part of the Japanese National Hydrate Research Program (MH21-S, funded by Ministry of Economy, Trade and Industry), received the samples at Sapporo, Japan for advanced core analysis. High-resolution X-ray CT was used to analyze the quality of the samples, which showed undisturbed lithological layers. Cores were lathed into cylindrical shape and distributed for multi property measurements (Figure 1, c)).<p>As a result, sediment from Unit-D is categorized as silty sand at ~37% porosity with ~80% gas hydrate saturation. An average hydration number n = 6.16 was measured by Raman spectroscopy. An average intrinsic permeability of ~400 mD and in situ effective permeability (with hydrate) on the order of ~10 mD. The Unit B recovered cores consisted of well sorted sand at ~40% porosity with ~95% gas hydrate saturation. An average intrinsic permeability of ~1 Darcy and in situ effective permeability on the order of ~30 mD was measured for the Unit B cores. There was a small permeability reduction due to porosity loss with increasing effective stress that simulated consolidation behavior along with depressurization in the highly permeable sandy sediment. The apparent minimum change in porosity and permeability may be caused by the low compressibility of quartz sand grains in the recovered cores. XRD and thermal conductivity analysis also suggested high quartz content. Triaxial compression tests established internal friction angles based on the Mohr-Coulomb's failure criterion, which are 40° for hydrate-bearing sediment and 29.8° for hydrate free sediment.</p>

Yoneda, Jun↗
DOE OSTI2020

Alaska North Slope 2018 Hydrate-01 Stratigraphic Test Well: Technical Results

The Hydrate-01 Stratigraphic Test Well was drilled in December 2018 to confirm that a seismically-identified location within the western Prudhoe Bay Unit might be suitable for extended-duration scientific production testing. The well featured the acquisition of a full suite of logging-while-drilling data, collection of side-wall pressure cores, and installation of distributed temperature and distributed acoustic sensor (DTS, DAS) fiber-optic cables. Evaluation of the logging-while-drilling data confirms gas hydrate is present at high saturation in two target sands of high reservoir quality. Acquired logs and samples enable critical petrophysical information to be compiled for input into production models. The well tested two primary targets: the deeper Unit B is highly favorable due to optimal reservoir temperature and minimal observed risk for direct communication with permeable, hydrate-free water-bearing zones. The shallower Unit D provides a secondary target and opportunity to

Boswell, Ray↗
DOE OSTI2020

Gas Hydrate Saturation Estimation Form Acoustic Log Data in the 2018 Alaska North Slope Hydrate-01 Stratigraphic Test

Completed in December 2018, the Alaska North Slope Hydrate 01 stratigraphic test well provides a wealth of logging-while-drilling (LWD) data for strata to below the base of gas hydrate stability (BGHS). This well is intended to be the first of three wells drilled for a comprehensive long-term gas hydrate production test conducted by the National Energy Technology Laboratory, the Japan Oil, Gas and Metals National Corporation, and the U.S. Geological Survey (USGS). The Hydrate 01 stratigraphic test well confirmed the presence of gas hydrate in two sand reservoirs within the hydrate stability zone, indicating the suitability of this location for a long-term gas hydrate production test.<p>The USGS, using an effective-medium-theory rock-physics approach, has estimated gas hydrate saturations from compressional (P) and shear (S) wave log data acquired in the Hydrate 01 well. We assume that gas hydrate occurs as pore-filling load-bearing material (i.e., part of the grain matrix). For Unit D, approximately 500 feet above the BGHS, both P-wave and S-wave acoustic logs indicate moderate gas hydrate saturations with S-wave results slightly lower than those for P-waves. For the Unit B, located just above the BGHS, we obtain moderate to high gas hydrate saturation estimates from both sonic logs. Our P-wave saturation estimates agree well with results from electrical-resistivity-based estimates, whereas estimates from nuclear magnetic resonance LWD data generally suggest 5 to 10 percent higher saturations; our S-wave results suggest lower saturations. These differences likely indicate complexities in the form of gas hydrate occurrence within the sediment pore space, potentially including differences between hydrate occurrence in Units D and B.</p>

Haines, Seth↗