Search NASA⌕ Search

Engineering topics

Collins, Ben

Publications and source records attributed to Collins, Ben.

A COUPLED DETERMINISTIC TRANSPORT CALCULATION IN COMSOL USING PROPER ORTHOGONAL DECOMPOSITION

A coupled physics problem consisting of radiation transport and heat transfer was modeled using COMSOL Multiphysics to simulate a criticality accident. Reduced order models (ROM) were created to accelerate the radiation transport calculation through Proper Orthogonal Decomposition (POD). Additionally, on-the-fly neutron cross sections were generated from a non-linear function through a feed forward neural network. The Livelink for MATLAB module allowed for data transfer between an otherwise independent solver and in-house modules. A data driven approach to POD was developed to act as a surrogate model to couple with heat transfer, with the POD module written in MATLAB coupled to an isolated heat transfer solve in COMSOL. A coupled transient solution resulted in a good approximation of the flux and temperature, with the maximum error being 3E-2 and 2.5E-3 respectively.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Parallel simulated annealing with embedded machine learning and multifidelity models for reactor core design

This paper presents extensions to a penalty-free, parallel simulated annealing (SA) algorithm for multi-constrained combinatorial optimization with the aim of embedding multi-fidelity physics models into the annealing procedure. The method uses a low-fidelity, quickly executing model for rapid design space exploration and a high-fidelity model for detailed constraint resolution and on-the-fly bias correction. Machine learning models updated within the annealing procedure were used to bridge the gap between the multi-fidelity models, which led to accurate rapid exploration and efficient detailed constraint resolution. A software implementation of the new multi-fidelity optimization methods, called ML-PSA, was demonstrated on a continuous multi-fidelity optimization problem and a constrained combinatorial PWR lattice design problem. These problems demonstrate some of the features, parallel performance characteristics, and extensible nature of the multi-fidelity SA methods. This paper shows that the developed software and procedure are a general optimization tool that can be applied to a wide variety of scientific and engineering design optimization applications. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

MPACT Programmer's Manual (V.4.3)

Figure 1 shows a high-level call chart for MPACT. The call chart uses the actual procedure names, starting with the main program name, MPACT. The only exception is the italicized names where the upstream procedure contains a number of subroutines calls. These calls are logically separated into blocks, such as setup basic info/inputs. Brief descriptions of what the procedure accomplishes are provided where needed. More detailed procedure information, including procedure arguments and definitions, can be found directly in the procedure header in the MPACT source code or Doxygen documentation (http://www.doxygen.nl/).

97 MATHEMATICS AND COMPUTING↗

Summary of improvements in modeling for fidelity and performance in MAMBA during FY18

This milestone report summarizes the FMC work on improvements to the MAMBA modeling methodology. The work was performed in close collaboration with the PHI as well as THM focus area and it was undertaken to improve both the physical fidelity and computational performance of MAMBA. We first describe the path towards identifying and then resolving issues in the MAMBA code and the underlying physics models that were still remaining at the beginning of FY18, after the code re-write in the previous year. These were primarily related to boiling and species transport, especially boron, within the CRUD. The code problems originated in the MAMBA3D code, from which the development of the new re-written code started, but they were only identified during testing of the new MAMBA code. We purposefully discuss a number of alternative explanations and solutions to the main issue identified, since the two-phase character of fluid transport in the CRUD and the related mass transport are still sources of model uncertainty that we continue to investigate. The hands-on code development referenced in this report was done under PHI and this milestone mainly provided support in the form of analysis, literature review, code review and feedback to the code developers.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Verification of Vessel Fluence and Excore Modeling with VERA

This document outlines the completion of the L2:RTM.P17.01 milestone to deliver and report verification of vessel fluence and excore modeling capabilities in VERA to Advanced Modeling Applications (AMA). It gives details on the unit testing and initial verification of vessel fluence and excore detector calculations performed with VERA, as well as the plotting capabilities in VERAView. This capability is now ready for further testing and verification and validation by AMA.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Illustration of VERA Capabilities to Model a Typical iPWR SMR

Small modular reactors (SMRs) are being considered by the commercial nuclear power industry as an option for more distributed generation and for replacement of older fossil fuel generating facilities. SMRs are more compact than operating pressurized water reactors (PWRs), producing about 200 MWe as compared to 1000 MWe or higher for their full-sized cousins, and are offered as “expandable” units; that is, their modular design allows the utility to add more units progressively at the same site. In Summer 2014, CASL reported on a progression of demonstrations illustrating VERA’s ability to simulate a typical SMR of the iPWR type, while developing a simple core cycle design for cycle economic studies. The work included development of fuel assembly lattices, 3D single assembly and full core (quarter symmetry) simulations of the proposed core cycle design using the CASL Virtual Environment for Reactor Applications (VERA). The report concluded that it would be difficult for the SMR to operate for the target 1400 EFPD cycle length and that the fuel cost would be on the order of 50% higher as compared with a PWR. Unfortunately, the Reference 4 core cycle design did not include control component management. The iPWR is intended to be operated using the control rods for reactivity control, as opposed to using soluble boron (like most currently operating PWRs), and the introduction of the control rods is expected to affect the length of the cycle. Therefore, this work continues the previous CASL demonstration of VERA capability to simulate a typical iPWR core, including the development of a control component management strategy using the Reference 4 core design and utilizing the soon-to-be released VERA3.3 tools. Note that this study is not intended as a validation study; rather it is merely an illustration of VERA’s capabilities to simulate a typical iPWR. Simulations included two variations on control rod banks – a two-bank scheme and a ten-bank scheme. Both schemes were modelled using the VERA Common Input, and more than six iterations on each control rod scheme were simulated to arrive at a combination of rod banks and insertion depths that provided a core reactivity near the target k eff of 1.000 ± 0.001 (more than 50 cases run) over two calendar months. In particular, VERA was used to determine the hot excess reactivity for the core design with all rods out (ARO), and then iterative simulations with the rod banks inserted to determine the critical control rod bank positions were completed. VERA options to simplify the process were exercised as possible, particularly restart functionality, coupled thermal-hydraulics using the internal T-H solver, xenon, and depletion capability. The fuel shuffling functionality was not exercised, since the iPWR SMR features a once-through cycle. The VERA method of characteristics (MOC) neutronics subcomponent was used to predict power and reactivity with control rod maneuvering, both with and without thermal-hydraulic feedback. The problem was scaled from 35 CPU cores to 3815, effectively demonstrating the solution time with respect to computing capacity. Computer clusters at Oak Ridge National Laboratory, Idaho National Laboratory and Tennessee Valley Authority were used. These studies provide an additional illustration of the application of VERA to a typical iPWR SMR. Reference 4 previously demonstrated that the codes could handle the differences in geometry for the iPWR, and this study expanded the illustration to include control rod management. Further, the work illustrates the need for in-depth simulations to support effective control rod maneuvering for an iPWR and highlights the need for control rod reactivity search capability within VERA. Additionally, the development of a control rod bank reactivity search capability will be extremely useful for not only this application, but also for BWRs as CASL develops BWR capability in Phase 2.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗