Search NASA⌕ Search

Engineering topics

Condon, Justin

Publications and source records attributed to Condon, Justin.

Large-scale reactive thermoset printing: Complex interactions between temperature evolution, viscosity, and cure shrinkage

Thermoset composites are strong candidates for large-scale material extrusion additive manufacturing (AM). However, uncured thermoset composites become unstable as print height increases. Here, chemical initiation of vinyl ester immediately before deposition was used to suppress collapse and enable large-scale thermoset printing. Structural stability was assessed by printing thin walls at various layer times and monitoring thermal gradients with an infrared camera. Stable printing was observed at a layer time of 4.50 min, approximately half the gel time of the material (8 min). Self-weight collapse occurred at short layer time (0.68 min), whereas warpage occurred at long layer time (6.50 min). Here, a new behavior was discovered at intermediate layer time (2.25 min) where the heat generated by the reaction causes new, un-gelled layers to flow. Forced convection eliminates this behavior, stabilizing the 2.25-min layer time print. These findings motivated development of a less exothermic material system, which was used to print a large-scale mold and demonstrate the value of this understanding. By presenting these challenges of large-scale reactive thermoset AM for the first time, this work motivates focused studies of the complex interplay between rheological, thermal, and chemical behaviors to improve the feasibility of large-scale thermoset AM. Tensile properties of the printed material were also measured. Longitudinal and transverse elastic moduli are 3.79 and 2.95 GPa, respectively, and corresponding tensile strengths are 36.11 and 18.83 MPa. The glass transition temperature is 93.13 °C.

36 MATERIALS SCIENCE↗

The impact of infill percentage and layer height in small-scale material extrusion on porosity and tensile properties

We report material extrusion additive manufacturing is prone to introducing porosity within the structure due to the layer-by-layer construction using elliptical beads of material. This open porosity ultimately plays a role in determining the mechanical properties of printed parts. The shape, size, and amount of porosity within a printed part is influenced by a variety of factors, including nozzle diameter, infill percentage, layer height, raster orientation, and print speed. While several studies have investigated these and other parameters’ effects on mechanical performance and porosity, better understanding the interconnected relationships is crucial in balancing the various input parameters to achieve maximum strength. This work initially examined the influence of key print parameters (infill percentage and layer height) on the internal porosity of a printed Acrylonitrile Butadiene Styrene (ABS) part. Then, the print parameters and internal porosity were statistically correlated to final mechanical properties. Porosity was further classified as either open or closed to differentiate between connected voids in the mesostructure from isolated voids within the material itself. Mechanical performance increased with an increasing density and infill percentage, displaying a 224 % increase in elastic modulus and a 150 % increase in ultimate tensile strength. The contribution of layer height was found to be conditional upon the infill percentage.

3D Printing↗

CHARACTERIZING THE INFLUENCE OF PRINT PARAMETERS ON POROSITY AND RESULTING DENSITY

Extrusion deposition additive manufacturing produces parts with inherent porosity, which typically manifests as easily accessible voids between beads. This open porosity can also be accompanied by voids within the beads themselves, and both types can impact a part’s desired performance. Porosity is influenced by a variety of factors, including infill percentage, layer height, nozzle diameter, print speed, and raster orientation. While their influence on mechanical properties and porosity have been studied previously, there has been minimal work connecting print parameters to porosity and subsequently to mechanical performance. This study investigates the relationships between print parameters, volumetric porosity, and mechanical performance. In addition, this study measures both open and closed porosity through use of a helium pycnometer rather than image analysis of a cross-section. Thus, this study will identify correlations between the volumetric density of parts and the resulting mechanical performance as a function of print parameters.

Brackett, James↗

Replacing Metal-Based Lightning Strike Protection Layer of CFRPS by 3D Printed Electronically Conductive Polymer Layer

Electrically conductive adhesive layers were deposited on top of aerospace grade carbon fiber reinforced plastic (CFRP) panels using a small-scale 3D printer. Polylactic acid (PLA) filaments with copper filler (CU-PLA) and graphene filler (GO-PLA) were used to print around 0.7 mm thick electrically conductive layer on top of CFRP panels. 3D printed polymeric layers were tested for their effectiveness as a lightning strike protection (LSP) material by subjected to a simulated lightning strike. A painted, electrically non-conductive unprotected panel was also tested for comparison. In the case of the CU-PLA protected sample, a high electrical conductivity proved to be useful in fast dissipation of the lightning current. Fast current dissipation helped to reduce the resistive heating after a lightning strike. Thermography and high-speed camera analysis were employed to study the heat generation and current dissipation during the lightning strike. These results established that a useful Faraday Cage was applied via additive manufacturing successfully. This work shows the successful application of 3D printing for producing LSP technologies, with future work aimed at investigating optimal printable electrically conductive thermoset material candidates.

Kumar, Vipin↗

3D PRINTED LAYER OF POLYANILINE-BASED CONDUCTIVE POLYMER FOR LIGHTNING STRIKE PROTECTION OF CFRPS

Manufacturing of Carbon Fiber Reinforced Plastics (CFRPs) using additive manufacturing (AM), or 3D printing, has gained popularity in recent years. It is believed that the AM industry has the potential to manufacture CFRP parts in a faster, easier and more economical way. Lightning strike damage to CFRP parts is not rare; therefore, additional lightning strike protection (LSP) technologies are applied on top of CFRP structures. However, there is no report of manufacturing lightning strike protection (LSP) technologies using the AM process. In the present work, the authors applied an electrically conductive layer via additive manufacturing. The material of the electrically conductive layer was a Polyaniline (PANI)-filled thermoset composite. This layer of PANI was deposited on top of the CFRP panels. The PANI-coated CFRP panels were tested against a simulated lightning strike made of a continuous waveform with component A (100 kA), component B (2 kA) and component C (470 A). The highly conductive PANI-layer worked as a capable Faraday cage to safely dissipate the lightning current. In PANI-based LSP, direct contact between PANI chains dominated the conduction behavior, which proved to be a highly efficient way to reduce resistive heating from the incident current. However, poor adhesion between the printed layer and the substrate structure needs to be improved in the future. The results from the thermal camera and the high-speed camera images showed an effective current dissipation through the printed layers. Non-destructive ultrasonic imaging was done to confirm the direct lightning damages to samples. The present work shows that a non-metallic conductive layer can be applied as an LSP of CFRP structures via an additive manufacturing technique.

Kumar, Vipin↗