Search NASA⌕ Search

Engineering topics

Connor Klauss

Publications and source records attributed to Connor Klauss.

4 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2022

Stability Analysis of Streaks Induced By Optimized Vortex Generators

Numerical computations are performed to investigate the potential for transition control in an axisymmetric boundary layer via fully realizable, streamwise stationary streaks induced by an azimuthally periodic array of surface mounted vortex generators (VGs). Previous work has shown that suitable streaks of this type can significantly reduce the growth of Mack’s second mode instabilities, but large streak amplitudes can make the flow susceptible to previously absent streak instabilities that can become the leading cause of transition. Here, we use the adjoint capabilities of the SU2 flow solver to optimize the VG shape to maximize the reduction in the growth of second-mode disturbances while also preventing the streak amplitudes from reaching large enough values to precipitate an earlier onset of transition via streak instabilities. The geometry and the freestream flow conditions are selected to match a relevant trajectory lo-cation from the HIFiRE-1 flight experiment. Results show that the optimized VGs can increase the mean streak amplitude by 117% with respect to a manually developed baseline design. The stability of this optimized basic state is analyzed via the plane-marching parabolized stability equations, predicting a fully laminar flow over the entire cone, or equivalently, yielding transition delay of 130% versus the 17% for the baseline VGs.

Boundary layer transition↗
NASA NTRS2022

Stability Analysis of Streaks Induced by Optimized Vortex Generators

Numerical computations are performed to investigate the potential for transition control in an axisymmetric boundary layer via fully realizable, streamwise stationary streaks induced by an azimuthally periodic array of surface mounted vortex generators (VGs). Previous work has shown that suitable streaks of this type can significantly reduce the growth of Mack’s second mode instabilities, but large streak amplitudes can make the flow susceptible to previously absent streak instabilities that can become the leading cause of transition. Here, we use the adjoint capabilities of the SU2 flow solver to optimize the VG shape to maximize the reduction in the growth of second-mode disturbances while also preventing the streak amplitudes from reaching large enough values to precipitate an earlier onset of transition via streak instabilities. The geometry and the freestream flow conditions are selected to match a relevant trajectory lo-cation from the HIFiRE-1 flight experiment. Results show that the optimized VGs can increase the mean streak amplitude by 117% with respect to a manually developed baseline design. The stability of this optimized basic state is analyzed via the plane-marching parabolized stability equations, predicting a fully laminar flow over the entire cone, or equivalently, yielding transition delay of 130% versus the 17% for the baseline VGs.

Boundary layer transition↗
NASA NTRSDate not supplied

Eigenvalue Sensitivity Computations for Linear Stability Theory

To realize the drag reduction benefit of boundary-layer transition control strategies, it is crucial to integrate transition prediction into the vehicle design through an optimization process. The integration of transition prediction based on linear stability analysis into adjoint d design optimization requires coupling an adjoint enabled computational fluid dynamics (CFD) solver with an adjoint enabled linear stability code. In particular, the boundary-layer transition location is often predicted using the N-factor method based on linear stability theory (LST). Thus, sensitivity of the linear-stability eigenvalues constitute an essential building block for optimizing the laminar flow performance. The present paper describes an implementation of LST eigenvalue sensitivity analysis that can be easily coupled with a CFD solver. Specifically, we describe a discrete adjoint formulation for the transition location prediction based on the N-factor method. The verification of this formulation is carried out by comparing the adjoint-based sensitivity of the local growth rate of a given instability mode with respect to the disturbance frequency, and the adjoint-based sensitivity of the transition location with respect to spanwise wavenumber with those sensitivities computed using a finite-difference approximation. Finally, the adjoint LST formulation is applied to flat-plate boundary-layer flows at transonic, supersonic, and hypersonic conditions, to determine the behavior and sensitivities of the transition location with respect to a range of disturbance spanwise wavenumbers.

Boundary Layer Transition↗