Search NASA⌕ Search

Engineering topics

Contreras, M A

Publications and source records attributed to Contreras, M A.

How Grain Boundaries in Cu(In,Ga)Se2 Thin Films are Charged: Revisit

Potential measurements on Cu(In,Ga)Se{sub 2} thin films using scanning Kelvin probe force microscopy have been reported extensively to address grain-boundary (GB) recombination by examining GB charging. However, the results are highly inconsistent. We revisit this issue by measuring high- and low-quality wide-bandgap films and using a complementary method of scanning capacitance microscopy. Our results show consistent positively charged GBs in our high-quality films with minimal surface defects, except for the {Sigma}3[112] GBs, which are charge neutral. We discuss possible artifacts due to surface defects when examining the GB charging and the role of GBs in the device performance.

14 SOLAR ENERGY↗

Comparative Study of Zn(O,S) Buffer Layers and CIGS Solar Cells Fabricated by CBD, ALD, and Sputtering: Preprint

Zn(O,S) thin films were deposited by chemical bath deposition (CBD), atomic layer deposition, and sputtering. Composition of the films and band gap were measured and found to follow the trends described in the literature. CBD Zn(O,S) parameters were optimized and resulted in an 18.5% efficiency cell that did not require post annealing, light soaking, or an undoped ZnO layer. Promising resultswere obtained with sputtering. A 13% efficiency cell was obtained for a Zn(O,S) emitter layer deposited with 0.5%O2. With further optimization of process parameters and an analysis of the loss mechanisms, it should be possible to increase the efficiency.

14 SOLAR ENERGY↗

Determination of Grain Boundary Charging in Cu(In,Ga)Se2 Thin Films: Preprint

Surface potential mapping of Cu(In,Ga)Se2 (CIGS) thin films using scanning Kelvin probe force microscopy (SKPFM) aims to understand the minority-carrier recombination at the grain boundaries (GBs) of this polycrystalline material by examining GB charging, which has resulted in a number of publications. However, the reported results are highly inconsistent. In this paper, we report on thepotential mapping by measuring wide-bandgap or high-Ga-content films and by using a complementary atomic force microscopy-based electrical technique of scanning capacitance microscopy (SCM). The results demonstrate consistent, positively charged GBs on our high-quality films with minimal surface defects/charges. The potential image taken on a low-quality film with a 1.2-eV bandgap showssignificantly degraded potential contrast on the GBs and degraded potential uniformity on grain surfaces, resulting from the surface defects/charges of the low-quality film. In contrast, the potential image on an improved high-quality film with the same wide bandgap shows significantly improved GB potential contrast and surface potential uniformity, indicating that the effect of surface defectsis critical when examining GB charging using surface potential data. In addition, we discuss the effect of the SKPFM setup on the validity of potential measurement, to exclude possible artifacts due to improper SKPFM setups. The SKPFM results were corroborated by using SCM measurements on the films with a CdS buffer layer. The SCM image shows clear GB contrast, indicating different electricalimpedance on the GB from the grain surface. Further, we found that the GB contrast disappeared when the CdS window layer was deposited after the CIGS film was exposed extensively to ambient, which was caused by the creation of CIGS surface defects by the ambient exposure.

14 SOLAR ENERGY↗

Exploring High-Dimensional Data Space: Identifying Optimal Process Conditions in Photovoltaics: Preprint

We demonstrate how advanced exploratory data analysis coupled to data-mining techniques can be used to scrutinize the high-dimensional data space of photovoltaics in the context of thin films of Al-doped ZnO (AZO), which are essential materials as a transparent conducting oxide (TCO) layer in CuInxGa1-xSe2 (CIGS) solar cells. AZO data space, wherein each sample is synthesized from a differentprocess history and assessed with various characterizations, is transformed, reorganized, and visualized in order to extract optimal process conditions. The data-analysis methods used include parallel coordinates, diffusion maps, and hierarchical agglomerative clustering algorithms combined with diffusion map embedding.

14 SOLAR ENERGY↗

Improved Energy Conversion Efficiency in Wide Bandgap Cu(In,Ga)Se2 Solar Cells

This report outlines improvements to the energy conversion efficiency in wide bandgap (E{sub g} > ;1.2 eV) solar cells based on CuIn{sub 1-x}Ga{sub x}Se{sub 2}. Using (a) alkaline containing high temperature glass substrates, (b) elevated substrate temperatures 600 C-650 C and (c) high vacuum evaporation from elemental sources following NREL's three-stage process, we have been able to improve the performance of wider bandgap solar cells with 1.2 < E{sub g} < 1.45 eV. Initial results of this work have led to efficiencies >18% for absorber bandgaps {approx}1.30 eV and efficiencies {approx}16% for bandgaps up to {approx}1.45 eV. In comparing J-V parameters in similar materials, we establish gains in the open-circuit voltage and, to a lesser degree, the fill factor value, as the reason for the improved performance. The higher voltages seen in these wide gap materials grown at high substrate temperatures may be due to reduced recombination at the grain boundary of such absorber films. Solar cell results, absorber materials characterization, and experimental details are reported.

14 SOLAR ENERGY↗

Surface Modification of Polycrystalline Cu(In,Ga)Se2 Thin-Film Solar Cell Absorber Surfaces for PEEM Measurements

We present a thorough examination of the {micro}m-scale topography of Cu(In, Ga)Se{sub 2} ('CIGSe') thin-film solar cell absorbers using different microscopy techniques. We specifically focus on the efficacy of preparing smooth sample surfaces - by etching in aqueous bromine solution - for a spatially resolved study of their chemical and electronic structures using photoelectron emission microscopy (PEEM). The etching procedure is shown to reduce the CIGSe surface roughness from ca. 40 to 25 nm after 40s etching, resulting in an increase in the quality of the obtained PEEM images. Furthermore we find that the average observed grain size at the etched surfaces appears larger than at the unetched surfaces. Using a liftoff procedure, it is additionally shown that the backside of the absorber is flat but finely patterned, likely due to being grown on the finely-structured Mo back contact.

14 SOLAR ENERGY↗

Sulfur gradient-driven Se diffusion at the CdS/CuIn(S,Se){sub 2} solar cell interface

The diffusion behavior of Se at the CdS/Cu(In,Ga)(S,Se){sub 2} thin film solar cell interface was investigated by x-ray photoelectron spectroscopy and x-ray excited Auger electron spectroscopy. Buffer/absorber structures with S/Se ratios between zero and three at the initial Cu(In,Ga)(S,Se){sub 2} surface were analyzed. Samples from a high-efficiency laboratory process (NREL) as well as from an industrial large-area process (AVANCIS) were investigated. We find selenium diffusion into the CdS buffer layer, the magnitude of which strongly depends on the S content at the absorber surface. The associated modification of the heterojunction partners has significant impact on the electronic structure at the interface.

36 MATERIALS SCIENCE↗