Search NASA⌕ Search

Engineering topics

Conway, Adam M.

Publications and source records attributed to Conway, Adam M..

Wide bandgap optical switch circuit breaker for controlling propagation of current therethrough a wide bandgap optical device

A high-voltage switch is adapted for use as a medium-voltage direct current circuit breaker, which provides a low-cost, small-footprint device to mitigate system faults. In one example, a method for operating a wideband optical device includes illuminating the wide bandgap optical device with a light within a first range of wavelengths and a first average intensity, allowing a current to propagate therethrough without substantial absorption of the current, illuminating the wide bandgap optical device with light within the first range of wavelengths and a second average intensity that is lower than the first average intensity to allow a sustained current flow though the wide bandgap optical device, and illuminating the wide bandgap optical device with light within a second range of wavelengths to stop or substantially restrict propagation of the current through the wide gap material.

Voss, Lars F.↗

Wide bandgap optical switch circuit breaker

A high-voltage switch is adapted for use as a medium-voltage direct current circuit breaker, which provides a low-cost, small-footprint device to mitigate system faults. In one example, a method for operating a wideband optical device includes illuminating the wide bandgap optical device with a light within a first range of wavelengths and a first average intensity, allowing a current to propagate therethrough without substantial absorption of the current, illuminating the wide bandgap optical device with light within the first range of wavelengths and a second average intensity that is lower than the first average intensity to allow a sustained current flow though the wide bandgap optical device, and illuminating the wide bandgap optical device with light within a second range of wavelengths to stop or substantially restrict propagation of the current through the wide gap material.

Voss, Lars F.↗

Tunnel drift step recovery diode

Devices, methods and techniques are disclosed for providing a multi-layer diode without voids between layers. In one example aspect, a multi-stack diode includes at least two Drift Step Recovery Diodes (DSRDs). Each DSRD comprises a first layer having a first type of dopant, a second layer forming a region with at least ten times lower concentration of dopants compared to the adjacent layers, and a third layer having a second type of dopant that is opposite to the first type of dopant. The first layer of a second DSRD is positioned on top of the third layer of first DSRD. The first layer of the second DSRD and the third layer of the first DSRD are degenerate to form a tunneling diode at an interface of the first DSRD and second DSRD, the tunneling diode demonstrating a linear current-voltage characteristic.

Voss, Lars F.↗

Extrinsic Absorption Pathways in Vanadium-Doped SiC Measured Using a Total Internal Reflection Geometry

Vanadium-doped SiC is under study for high-power photoconductive switches and is receiving increased attention as a potential material system for quantum computing, as the V can act as a quantum emitter at telecom wavelengths. Knowledge of the defect-mediated electronic transition pathways from sub-bandgap illumination in this material with low absorption and multi-photon and multi-path transition probability is important in optimizing quantum efficiency. Herein, the optical transitions of vanadium-doped SiC for two polytypes as a function of dopant concentration using a total internal reflection (TIR) geometry are examined. Furthermore, normalized quantum efficiency is reported and correlated with both dopant concentrations (V, N, B, and Al) measured by secondary ion mass spectroscopy (SIMS) and absorption measurements. Although both polytypes respond well to 532 nm light, efficiency at longer wavelengths does not correlate 1:1 with absorption coefficient and strongly depends on the polytype and net background co-dopant concentration. This has important implications for efficient excitation of both carriers for optoelectronics and for the use of V as a quantum emitter.

36 MATERIALS SCIENCE↗

Photoconductive Switch with High Sub-Bandgap Responsivity in Nitrogen-Doped Diamond

To evaluate nitrogen-doped diamond as a candidate for Photoconductive Semiconductor Switches (PCSS) triggered in the sub-bandgap visible range, we have fabricated and tested diamond PCSS from a set of diamond grades of varying nitrogen concentration. The nitrogen-doped diamond PCSS have higher responsivity than other diamond optoelectronic devices in the visible range. We present a novel demonstration of sub-bandgap triggered diamond PCSS, which when scaled to higher voltage, can compete with and even surpass performance of existing ultraviolet-triggered diamond PCSS. This work suggests that nitrogen-doped diamond is a promising candidate for high-power, fast optoelectronic devices.

36 MATERIALS SCIENCE↗

Maskless random antireflective nanotexturing of single crystal SiC

Random nanotexturing of optics and semiconductors has proven to be a highly effective way to produce high transmittivity, low reflective surfaces. Here, the authors report a one-step technique using SF6 reactive ion etching to produce nanotexturing of SiC. The effect of etching process power and time is optimized to demonstrate sub-1% specular reflectance and below 5% total reflectance over the 400–2000 nm spectral range. The technique is applied to compare measurements of a photoconductive switch with untreated and treated surfaces. In conclusion, using a white light source emitting in the range 400–750 nm, the authors show that the decrease in specular reflectivity results in a 20% increase in the photocurrent response.

36 MATERIALS SCIENCE↗

A Total Internal Reflection Photoconductive Switch

We demonstrate a novel illumination technique for extrinsic photoconductive switches based on the creation of a total internal reflection trap to increase the optical path length. The optimal geometry is a square substrate illuminated from one of the corners along the diagonal, ensuring that the total internal reflection condition is maintained after any reflection off the device lateral sides. The optical absorption uniformity throughout the device bulk was improved by designing the entry window to have a cylindrical shape and by using a square core optical fiber as an illumination source. In conclusion, the concept is experimentally validated on a vanadium-doped silicon carbide device that shows approximately four-fold improvement in responsivity compared to normal illumination.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Pillar-structured neutron detector based multiplicity system

This work demonstrates the potential of silicon pillars filled with boron-10 as a sensor technology for a compact and portable neutron multiplicity system. Solid-state, semiconductor based neutron detectors may enable completely new detector form factors, offer an alternate approach to helium-3 based systems, and reduce detector weight and volume requirements. Thirty-two pillar-structured neutron detectors were assembled into a system with an active area of over 20 cm 2 and were used in this work to demonstrate the feasibility of this sensor technology as a potential replacement for helium-3 based gas detectors. Multiplicity measurements were successfully carried out using a californium-252 neutron source, in which the source mass, system efficiency, and die-away time were determined. As a result, this demonstration shows that these solid-state detectors could allow for a more compact and portable system that could be used for special nuclear material identification in the field.

42 ENGINEERING↗

Experimental determination of gamma-ray discrimination in pillar-structured thermal neutron detectors under high gamma-ray flux

Silicon pillar structures filled with a neutron converter material ( 10 B) are designed to have high thermal neutron detection efficiency with specific dimensions of 50 μm pillar height, 2 μm pillar diameter and 2 μm spacing between adjacent pillars. In this paper, we have demonstrated such a detector has a high neutron-to-gamma discrimination of 10 6 with a high thermal neutron detection efficiency of 39% when exposed to a high gamma-ray field of 10 9 photons/cm 2 s.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Sintered Cr/Pt and Ni/Au ohmic contacts to B{sub 12}P{sub 2}

Icosahedral boron phosphide (B{sub 12}P{sub 2}) is a wide-bandgap semiconductor possessing interesting properties such as high hardness, chemical inertness, and the reported ability to self-heal from irradiation by high energy electrons. Here, the authors developed Cr/Pt and Ni/Au ohmic contacts to epitaxially grown B{sub 12}P{sub 2} for materials characterization and electronic device development. Cr/Pt contacts became ohmic after annealing at 700 °C for 30 s with a specific contact resistance of 2 × 10{sup −4} Ω cm{sup 2}, as measured by the linear transfer length method. Ni/Au contacts were ohmic prior to any annealing, and their minimum specific contact resistance was ∼l–4 × 10{sup −4} Ω cm{sup 2} after annealing over the temperature range of 500–800 °C. Rutherford backscattering spectrometry revealed a strong reaction and intermixing between Cr/Pt and B{sub 12}P{sub 2} at 700 °C and a reaction layer between Ni and B{sub 12}P{sub 2} thinner than ∼25 nm at 500 °C.

36 MATERIALS SCIENCE↗

Three-dimensional boron particle loaded thermal neutron detector

Three-dimensional boron particle loaded thermal neutron detectors utilize neutron sensitive conversion materials in the form of nano-powders and micro-sized particles, as opposed to thin films, suspensions, paraffin, etc. More specifically, methods to infiltrate, intersperse and embed the neutron nano-powders to form two-dimensional and/or three-dimensional charge sensitive platforms are specified. The use of nano-powders enables conformal contact with the entire charge-collecting structure regardless of its shape or configuration.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Method for manufacturing solid-state thermal neutron detectors with simultaneous high thermal neutron detection efficiency (>50%) and neutron to gamma discrimination (>1.0E4)

Methods for manufacturing solid-state thermal neutron detectors with simultaneous high thermal neutron detection efficiency (>50%) and neutron to gamma discrimination (>10.sup.4) are provided. A structure is provided that includes a p+ region on a first side of an intrinsic region and an n+ region on a second side of the intrinsic region. The thickness of the intrinsic region is minimized to achieve a desired gamma discrimination factor of at least 1.0E+04. Material is removed from one of the p+ region or the n+ region and into the intrinsic layer to produce pillars with open space between each pillar. The open space is filed with a neutron sensitive material. An electrode is placed in contact with the pillars and another electrode is placed in contact with the side that is opposite of the intrinsic layer with respect to the first electrode.

36 MATERIALS SCIENCE↗

DHS HS-STEM Internship Summary Report

I had the opportunity to work at Lawrence Livermore National Laboratory within the MEMS, Electronics, and Photonics Technologies group. I worked under the direct supervision of Dr. Adam Conway and Dr. Erik Swanberg on a semiconductor based gamma ray detector. My work involved automating the experimental setup and data analysis portion of the project to alleviate the researcher’s busy schedules. A semiconductor is a material that has conductivity in between a metal and ceramic. In layman’s terms, if you provide it with just enough energy, charge can flow inside of the material. If we impose some form of ionizing radiation such as a gamma ray, we can detect the amount of energy imparted on the system by measuring the amount of charge produced in the material. Figure 1 outlines the process that a semiconductor undergoes to allow us to detect ionizing radiation. Certain materials properties make them ideal for gamma ray detection such as the average atomic number, carrier properties, resistivity, and bandgap energy. I was working with Thallium Bromide (TlBr) detectors for room temperature detection of gamma rays, specifically looking at how different metal electrodes affected the stability of our system. My work involved automating the stress and voltage tests applied to the TlBr detectors and allowing for easy analysis of the data to determine if the system was still functional.

36 MATERIALS SCIENCE↗

Energy resolution in semiconductor gamma radiation detectors using heterojunctions and methods of use and preparation thereof

In one embodiment, a system comprises a semiconductor gamma detector material and a hole blocking layer adjacent the gamma detector material, the hole blocking layer resisting passage of holes therethrough. In another embodiment, a system comprises a semiconductor gamma detector material, and an electron blocking layer adjacent the gamma detector material, the electron blocking layer resisting passage of electrons therethrough, wherein the electron blocking layer comprises undoped HgCdTe. In another embodiment, a method comprises forming a hole blocking layer adjacent a semiconductor gamma detector material, the hole blocking layer resisting passage of holes therethrough. Additional systems and methods are also presented.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗