Engineering topics

Cook, W. J.

Publications and source records attributed to Cook, W. J..

16 records

NASA NTRS1986

Photoelectronic Monitor of Motion Sickness

Instrument includes gallium arsenide light-emitting diode (LED) and silicon phototransistor with infrared filter, all cast in single plastic housing. Housing attached to subject's face with transparent doublesided adhesive tape. LED directs pulses of infrared light to skin, which reflects them to phototransistor. Phototransistor produces signal that is processed by external circuits to yield plot of infrared reflectance with time. External circuits temperature-compensated and respond only to pulsed component of detector output, rejecting those components caused by stray light. Circuits also extract blood-volume pulse amplitude and heart rate.

Oman, C. M.↗

NASA NTRS1986

Response of hot element wall shear stress gages in laminar oscillating flows

An experimental investigation of the time-dependent response of hot element wall shear stress gages in unsteady periodic air flows is reported. The study has focused on wall shear stress in laminar oscillating flows produced on a flat plate by a free stream velocity composed of a mean component and a superposed sinusoidal variation. Two types of hot element gages, platinum film and flush wire, were tested for values of reduced frequency ranging from 0.14 to 2.36. Values of the phase angle of the wall shear stress variation relative to the free stream velocity, as indicated by the hot element gages, are compared with numerical prediction. The comparisons show that the gages indicate a wall shear stress variation that lags the true variation, and that the gages will also not indicate the correct wall shear stress variation in periodic turbulent flows.

Cook, W. J.↗

NASA NTRS1986

Turbulent Boundary Layers in Oscillating Flows. Part 1: an Experimental and Computational Study

An experimental-computational study of the behavior of turbulent boundary layers for oscillating air flows over a plane surface with a small favorable mean pressure gradient is described. Experimental studies were conducted for boundary layers generated on the test section wall of a facility that produces a flow with a mean free stream velocity and a superposed nearly-pure sinusoidal component over a wide range of frequency. Flow at a nominal mean free stream velocity of 50 m/s were studied at atmospheric pressure and temperature at selected axial positions over a 2 m test length for frequencies ranging from 4 to 29 Hz. Quantitative experimental results are presented for unsteady velocity profiles and longitudinal turbulence levels obtained from hot wire anemometer measurements at three axial positions. Mean velocity profiles for oscillating flows were found to exhibit only small deviations from corresponding steady flow profiles, while amplitudes and phase relationships exhibited a strong dependence on axial position and frequency. Since sinusoidal flows could be generated over a wide range of frequency, studies at fixed values of reduced frequency at different axial positions were studied. Results show that there is some utility in the use of reduced frequency to correlate unsteady velocity results. The turbulence level u' sub rms was observed to vary essentially sinusoidally around values close to those measured in steady flow. However, the amplitude of oscillation and phase relations for turbulence level were found to be strongly frequency dependent. Numerical predictions were obtained using an unsteady boundary layer computational code and the Cebeci-Smith and Glushko turbulence models. Predicted quantities related to unsteady velocity profiles exhibit fair agreement with experiment when the Cebeci-Smith turbulence model is used.

Cook, W. J.↗

NASA NTRS1986

Response of hot element flush wall gauges in oscillating laminar flow

The time dependent response characteristics of flush-mounted hot element gauges used as instruments to measure wall shear stress in unsteady periodic air flows were investigated. The study was initiated because anomalous results were obtained from the gauges in oscillating turbulent flows for the phase relation of the wall shear stress variation, indicating possible gauge response problems. Flat plate laminar oscillating turbulent flows characterized by a mean free stream velocity with a superposed sinusoidal variation were performed. Laminar rather than turbulent flows were studied, because a numerical solution for the phase angle between the free stream velocity and the wall shear stress variation that is known to be correct can be obtained. The focus is on comparing the phase angle indicated by the hot element gauges with corresponding numerical prediction for the phase angle, since agreement would indicate that the hot element gauges faithfully follow the true wall shear stress variation.

Giddings, T. A.↗

NASA NTRS1985

An experimental and computational study of turbulent boundary layers in oscillating flows

Cook, W. J.↗

NASA NTRS1984

Performance tests for the NASA Ames Research Center 20 cm x 40 cm oscillating flow wind tunnel

An evaluation is presented of initial tests conducted to assess the performance of the NASA Ames 20 cm x 40 cm oscillating flow wind tunnel. The features of the tunnel are described and two aspects of tunnel operation are discussed. The first is an assessment of the steady mainstream and boundary layer flows and the second deals with oscillating mainstream and boundary layer flows. Experimental results indicate that in steady flow the test section mainstream velocity is uniform in the flow direction and in cross section. The freestream turbulence intensity is about 0.2 percent. With minor exceptions the steady turbulent boundary layer generated on the top wall of the test section exhibits the characteristics of a zero pressure gradient turbulent boundary layer generated on a flat plate. The tunnel was designed to generate sinusoidal oscillating mainstream flows. Experiments confirm that the tunnel produces sinusoidal mainstream velocity variations for the range of frequencies (up to 15 Hz). The results of this study demonstrate that the tunnel essentially produces the flows that it was designed to produce.

Cook, W. J.↗

NASA NTRS1980

Test section configuration for aerodynamic testing in shock tubes

This paper presents results of a study of the test section configuration required to minimize or alleviate interference effects on model flow produced by the presence of test section walls in the aerodynamic testing of two dimensional transonic airfoils in a shock tube. Tests at a nominal Mach number of 0.85 and a chord Reynolds number of 2,000,000 were carried out by means of schlieren photography and pressure measurements for several symmetric airfoil profiles using shock tube test sections with unmodified straight walls, contoured walls, and slotted walls with adjacent chambers. Results were compared with corresponding results from conventional wind tunnel tests of the airfoils. Results for the straight wall tests show major airfoil flow distortions. Results from contoured wall tests and those performed using a slotted wall test section developed in this study exhibit essential agreement with wind tunnel results. The collective results show that test sections for aerodynamic testing can be designed for shock tubes that will alleviate wall interference effects.

Cook, W. J.↗

NASA NTRS1978

Application of shock tubes to transonic airfoil testing at high Reynolds numbers

Performance analysis of a gas-driven shock tube shows that transonic airfoil flows with chord Reynolds numbers of the order of 100 million can be produced, with limitations being imposed by the structural integrity of the facility or the model. A study of flow development over a simple circular arc airfoil at zero angle of attack was carried out in a shock tube at low and intermediate Reynolds numbers to assess the testing technique. Results obtained from schlieren photography and airfoil pressure measurements show that steady transonic flows similar to those produced for the same airfoil in a wind tunnel can be generated within the available testing time in a shock tube with properly contoured test section walls.

Cook, W. J.↗

NASA NTRS1978

A study of test section configuration for shock tube testing of transonic airfoils

Two methods are investigated for alleviating wall interference effects in a shock tube test section intended for testing two-dimensional transonic airfoils. The first method involves contouring the test section walls to match approximate streamlines in the flow. Contours are matched to each airfoil tested to produce results close to those obtained in a conventional wind tunnel. Data from a previous study and the present study for two different airfoils demonstrate that useful results are obtained in a shock tube using a test section with contoured walls. The second method involves use of a fixed-geometry slotted-wall test section to provide automatic flow compensation for various airfoils. The slotted-wall test section developed exhibited the desired performance characteristics in the approximate Mach number range 0.82 to 0.89, as evidenced by good agreement obtained between shock tube and wind tunnel results for several airfoil flows.

Cook, W. J.↗

NASA NTRS1978

The shock tube as a device for testing transonic airfoils at high Reynolds numbers

A performance analysis of gas-driven shock tubes shows that transonic airfoil flows with chord Reynolds numbers in the range of 100 million can be generated behind the primary shock in a large shock tube. A study of flow over simple airfoils has been carried out at low and intermediate Reynolds numbers to assess the testing technique. Results obtained from schlieren photos and airfoil pressure measurements show that steady transonic flows similar to those observed for the airfoils in wind tunnels can be generated within the available testing time in a shock tube with either properly-contoured test section walls or a properly-designed slotted-wall test section. The study indicates that the shock tube is a useful facility for studying two-dimensional high Reynolds number transonic airfoil flows.

Cook, W. J.↗

NASA NTRS1975

Correlation of boundary layer quantities for hypersonic laminar flows with zero pressure gradient for several gases

The laminar boundary layer has been theoretically studied for six gases for flows over cold walls with zero pressure gradient at Mach numbers between 5.5 and 12.5 to correlate boundary layer quantities for the various gases. The flow conditions considered correspond to those that can be generated in test facilities such as the shock tunnel and the expansion tube. Computed results obtained using real gas properties indicate that the Eckert number based on edge conditions serves to correlate the results in terms of the wall shear stress and enthalpy gradient, the Stanton number, and the momentum thickness for the various gases within plus or minus 10 per cent for Te = Tw and Te approximately 3Tw. Computed Reynolds analogy factors exhibit very good agreement with those predicted by the Colburn analogy. Velocity and displacement thicknesses correlate well with Eckert number for Te = Tw, but fail to correlate for Te approximately 3Tw. Differences in results are traced to property variations. Results show that the Eckert number is a significant correlating variable for the flows considered.

Cook, W. J.↗

NASA NTRS1975

Use of shock tubes in high Reynolds number transonic testing

The shock tube as a device to fulfill current needs for testing of transonic airfoils at high Reynolds numbers is considered. Performance analysis of a gas-driven shock tube shows that transonic airfoil flows with chord Reynolds numbers in the range of 100 million can be produced. A study of flow development over a simple airfoil has been carried out in a shock tube at low and intermediate Reynolds numbers to assess the testing technique. Results obtained from schlieren photography and airfoil pressure measurements show that steady transonic flows similar to those produced for the same airfoil in a wind tunnel can be generated within the available testing time in a shock tube with properly contoured test section walls. The study indicates that the shock tube is a viable alternative as a facility for studying high Reynolds number transonic airfoil flows.

Cook, W. J.↗

NASA NTRS1974

Experimental study of the shock-induced unsteady laminar boundary layer on a flat plate

The behavior of the unsteady laminar boundary layer induced by the incident shock wave passing over a flat plate mounted in a shock tube has been experimentally studied for shock speeds ranging from 2.35 to 7.34 km/sec by measuring unsteady heat transfer rates to the plate using thin-film heat-flux gages. Theoretical heat-transfer rates were predicted from analytical solutions in the literature which describe the unsteady flat plate boundary layer development for equilibrium real-gas flows. Experimental results obtained for both air and nitrogen were found to be in good agreement with the theoretical predictions.

Cook, W. J.↗

NASA NTRS1973

Correlation of heat transfer for the zero pressure gradient hypersonic laminar boundary layer for several gases

A theoretical study of heat transfer for zero pressure gradient hypersonic laminar boundary layers for various gases with particular application to the flows produced in an expansion tube facility was conducted. A correlation based on results obtained from solutions to the governing equations for five gases was formulated. Particular attention was directed toward the laminar boundary layer shock tube splitter plates in carbon dioxide flows generated by high speed shock waves. Computer analysis of the splitter plate boundary layer flow provided information that is useful in interpreting experimental data obtained in shock tube gas radiation studies.

Cook, W. J.↗

NASA NTRS1972

Characteristics of the unsteady shock-induced laminar boundary layer on a flat plate.

The unsteady shock-induced laminar boundary layer on a flat plate is theoretically studied for shock speeds ranging from 1.12 to 9 km/sec. Boundary layer flows for real air, assumed to be in thermochemical equilibrium, are analyzed by extending Lam's work on shock-induced laminar boundary layers to equilibrium dissociated and ionized flows. A complete description of the unsteady nature of the boundary layer is presented in terms of heat transfer and several boundary layer thickness quantities as functions of a single time-position variable. Boundary layer development is considered for two points of view. Time-dependent boundary layer development and approach to steady state for any fixed position on the plate is described, as is the configuration of the boundary layer with position on the plate at any point in time.

Cook, W. J.↗

NASA NTRS1972

Prediction and measurement of heat transfer rates for the shock-induced unsteady laminar boundary layer on a flat plate

The unsteady laminar boundary layer induced by the flow-initiating shock wave passing over a flat plate mounted in a shock tube was theoretically and experimentally studied in terms of heat transfer rates to the plate for shock speeds ranging from 1.695 to 7.34 km/sec. The theory presented by Cook and Chapman for the shock-induced unsteady boundary layer on a plate is reviewed with emphasis on unsteady heat transfer. A method of measuring time-dependent heat-transfer rates using thin-film heat-flux gages and an associated data reduction technique are outlined in detail. Particular consideration is given to heat-flux measurement in short-duration ionized shocktube flows. Experimental unsteady plate heat transfer rates obtained in both air and nitrogen using thin-film heat-flux gages generally agree well with theoretical predictions. The experimental results indicate that the theory continues to predict the unsteady boundary layer behavior after the shock wave leaves the trailing edge of the plate even though the theory is strictly applicable only for the time interval in which the shock remains on the plate.

Cook, W. J.↗