Engineering topics

Cooper, Alan R.

Publications and source records attributed to Cooper, Alan R..

13 records

DOE OSTI2022

Demonstration of low-level biogenic fuel content using quench curve and direct liquid scintillation counting (LSC) methods

In this work, an investigation into the direct method for liquid scintillation counting (LSC) quantification of biogenic fuel content in fuel blendstock is presented. This method development intentionally used a colored matrix (~99 wt%), fossil diesel fraction, and low-level biogenic fractions (~1 wt%) to determine the applicability of the LSC technique in colored blend mixtures. LSC procedures for quench correction, including the use of an instrument internal standard (Quantulus SQP values), color quench curves, and an internal 14 C standard spike on samples containing low-level amounts of biogenic gasoline, jet, and diesel mixed with fossil fuel, were compared. Samples were analyzed on both Perkin-Elmer Quantulus and Tri-Carb instruments, and the 14 C contents were compared with those determined by accelerator mass spectrometry (AMS). Results from the Tri-Carb instrument showed that percent differences of <10 % compared to AMS-reported values are achievable at 5-hour count times despite colored samples. A comparison between the impact of chemical and color quenching in the fuel samples showed that color quenching in highly colored samples reduces efficiency significantly more than chemical quenching, indicating that chemical quench curves are not appropriate for highly colored biofuel/fossil-fuel blended samples. Results indicate that both the direct method with internal spike quench correction and the use of a color-quench curve provide accurate results for 1 % biogenic fuel blends. Additionally, we have explored the use of Fourier transform infrared (FTIR) spectroscopy in measuring the biogenic content of the colored blended fuel samples. Preliminary results show the presence of biogenic carbon-derived fingerprints that are absent in fossil-derived sample. However, further work is needed to develop an FTIR-based quantitative method.

09 BIOMASS FUELS↗

DOE OSTI2020

Production and Fuel properties of Iso-Olefins with Controlled Molecular Structure and Obtained from Butene Oligomerization

The ability to control the molecular structure (e.g., degree of branching) of iso-olefins produced from oligomerizing light olefins is a valuable tool for tuning the final compositions of hydrocarbon fuels and targeting specific fuel properties. In this study, we demonstrated that the degree of branching of iso-olefins obtained from butene(s) oligomerization can be controlled by tuning process conditions (i.e., temperature, weight hourly space velocity [WHSV], and nature of butene feedstock) and by choosing the proper catalyst (i.e., Amberlyst-36 vs. Y/ZSM-22). In this study, we produced three types of iso-olefin mixtures: 1) a methyl-heptenes rich (74 wt.%) mixture, 2) dimethyl-hexenes rich (80–96 wt.%) mixtures, and 3) highly branched (i.e., more than three methyl substitutions) iso-olefins rich (>50 wt.%) mixtures. While dimethyl-hexenes are preferentially formed at lower temperatures (60–100°C) and WHSV (i.e., 2 hr-1), methyl-heptenes are favorably produced at higher temperatures (>100°C) and WHSVs (i.e., 7 hr-1) over Amberlyst-36. The use of either 1-butene or 2-butene as feedstock resulted in liquid products with similar branching because facile intramolecular isomerization occurs prior to oligomerization. However, the use of isobutylene feedstock forms a significantly more branched olefin product. The formation of highly branched iso-olefins also is favored at higher temperature (140°C) over Amberlyst-36. Using Y/ZSM-22 instead of Amberlyst-36 allowed preferential formation of less-branched methyl-heptenes. For each type of iso-olefins mixture, we determined fuel properties including research octane number (RON), motor octane number (MON), and octane sensitivity (S), which is the difference between RON and MON. We found that not only RON and MON but also S values increased with the degree of branching of these complex mixtures of iso-olefins. The highest RON of 99.7 and S value of 9.3 were obtained for a mixture of highly branched iso-olefins.

Dagle, Vanessa↗

DOE OSTI2019

Strategies to Valorize the Hydrothermal Liquefaction-Derived Aqueous Phase into Fuels and Chemicals

Valorization options for the aqueous fraction produced by the hydrothermal liquefaction of terrestrial feedstocks were developed. The processes focused on carboxylic acids, which are abundant in the aqueous fraction. A clean up process for the aqueous phase based on activated carbon absorption followed by liquid-liquid extraction was demonstrated that significantly reduces color bodies and inorganic contaminants while simultaneously concentrating desirable organic constituents. Conversion of the cleaned aqueous phase was then demonstrated for both a ketonization reaction and steam reforming. Condensed phase ketonization over LaxZryOz catalyst was found to exhibit both excellent hydrothermal stability and ketonization activity. Necessity for feedstock cleanup was established and stable condensed phase ketonization operation was demonstrated for ~100 hours with HTL-process derived material. Steam reforming was also demonstrated by employing a dual-bed catalyst configuration whereby carboxylic acids first undergo ketonization over CeO2 in the vapor phase followed by steam reforming of the ketone intermediates over Co/CeO2. The dual-bed approach reduced coke deposition and thus catalyst stability improved. Techno-economic analysis was used to assess economic viability for producing fuel from the bio-oil fraction and either propene (formed via hydrogenation and dehydration of acetone, the primary ketonization product) or hydrogen from the aqueous stream. The ketonization and steam reforming cases were separately modeled and benchmarked to a process utilizing anaerobic digestion. Resulting minimum fuel selling prices of $3.7, $4.2, and $4.3/GGE were obtained for the production of olefins via ketonization, reduction and dehydration; steam reforming; and anaerobic digestion processes, respectively. Both the steam reforming and anaerobic digestion processes benefited by avoiding the need for natural gas by producing the hydrogen on-site required for biocrude hydrotreatment. However, the condensed ketonization process had the lowest minimum fuel selling price because of the co-product olefins generated for sale.

Biomass, hydrothermal liquefaction, techno economi↗

DOE OSTI2019

Cleanup and Conversion of Biomass Liquefaction Aqueous Phase to C3–C5 Olefins over ZnxZryOz Catalyst

The viability of using a ZnxZryOz mixed oxide catalyst for the direct production of C4 olefins from the aqueous phase derived from three different bio-oils was explored. The aqueous phases derived from (i) hydrothermal liquefaction of corn stover, (ii) fluidized bed fast pyrolysis of horse litter, and (iii) screw pyrolysis of wood pellets were evaluated as feedstocks. While exact compositions vary, the primary constituents for each feedstock are acetic acid and propionic acid. Continuous processing, based on liquid–liquid extraction, for the cleanup of the inorganic contaminants contained in the aqueous phase was also demonstrated. Complete conversion of the carboxylic acids was achieved over ZnxZryOz catalyst for all the feedstocks investigated. The main reaction products from each of the feedstocks include isobutene (>30% selectivity) and CO2 (>23% selectivity). Activity loss from coking was also observed, thereby rendering deactivation of the ZnxZryOz catalyst, however, complete recovery of catalyst activity was observed following regeneration. Finally, the presence of H2 in the feed was found to facilitate hydrogenation of intermediate acetone, thereby increasing propene production and, consequently, decreasing isobutene production.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2018

Final Report for the Project Characterization and Valorization of Aqueous Phases Derived from Liquefaction and Upgrading of Bio-Oils

The Characterization and Valorization of Aqueous Phases Derived from Liquefaction and Upgrading of Bio-Oils project developed processes to extract value from the organics within aqueous streams derived from biomass direct liquefaction processes. The focus of the project was twofold. First, we characterized a diverse set of aqueous streams from numerous processes and feedstocks. The characterization effort served to inform this project toward development around the most prevalent compounds to maximize versatility and impact. We analyzed diverse streams from hydrothermal liquefaction of lignocellulosic, algal, and waste feedstocks; catalytic fast-pyrolysis aqueous phases; fast-pyrolysis aqueous phases; and aqueous phases produced by hydroprocessing of fast-pyrolysis bio-oil. Second, thermochemical catalytic processes were developed to convert aqueous-phase organics into useful products. These processes focused mostly on organic acids and specifically acetic acid, which was found to be ubiquitous from the characterization effort. A La x Zr y O z catalyst was discovered and developed for the ketonization of acids to ketones in the condensed aqueous phase. A dual-bed steam reforming process was developed to convert acids and other organics to hydrogen for bio-oil hydroprocessing. The dual-bed reforming process consisted of a ketonization step followed by a steam reforming step with Co as the active metal. The dual-bed process significantly reduced the rate of coke deposition versus direct steam reforming of the organic acids and beneficially produced CH 4 below the equilibrium value. Finally, we demonstrated direct conversion of aqueous-phase organics to olefins over a Zn x Zr y O z catalyst. Each thermochemical catalytic process was demonstrated with process-derived aqueous mixtures. Model compounds were used to benchmark performance and optimize conditions, but emphasis was placed on utilizing “real” aqueous streams whenever possible. A liquid-liquid extraction process using methyl tert-butyl ether as the solvent was developed to segregate dissolved inorganic species and sugars from desirable light oxygenates such as acids and alcohols. Furthermore, a carbon treatment to remove color bodies was employed after it was found the presumably heavy organic chromophore species deactivated catalysts. These economic separation processes allowed for the successful demonstration of stable catalytic processing in the condensed-phase ketonization, dual-bed reforming, and direct olefin production processes for tens to hundreds of hours, which were limited only by the quantity of feed available. Techno-economic analysis of these processes demonstrated the impact possible when capturing “waste” organics as valuable products. The condensed-phase ketonization process for converting aqueous stream acids to ketones followed by reduction and dehydration to olefins sold as a co-product resulted in the reduction of the minimum fuel selling price by about 13% compared to the anaerobic-digestion, aqueous-phase treatment base case (3.74 to 4.29/GGE). The dual-bed reforming process was commensurate in price to the anaerobic digestion base case (4.24 versus 4.29/GGE). However, the need for external natural gas to produce hydrogen for bio-oil hydroprocessing was eliminated, thereby lowering the carbon impact of the process.

09 BIOMASS FUELS↗

DOE OSTI2018

Systems and processes for conversion of ethylene feedstocks to hydrocarbon fuels

Systems, processes, and catalysts are disclosed for obtaining fuels and fuel blends containing selected ratios of open-chain and closed-chain fuel-range hydrocarbons suitable for production of alternate fuels including gasolines, jet fuels, and diesel fuels. Fuel-range hydrocarbons may be derived from ethylene-containing feedstocks and ethanol-containing feedstocks.

Lilga, Michael A.↗

DOE OSTI2018

Systems and processes for conversion of ethylene feedstocks to hydrocarbon fuels

Systems, processes, and catalysts are disclosed for obtaining fuel and fuel blends containing selected ratios of open-chain and closed-chain fuel-range hydrocarbons suitable for production of alternate fuels including gasolines, jet fuels, and diesel fuels. Fuel-range hydrocarbons may be derived from ethylene-containing feedstocks and ethanol-containing feedstocks.

09 BIOMASS FUELS↗

DOE OSTI2017

Aqueous-Phase Acetic Acid Ketonization over Monoclinic Zirconia

The effect of aqueous phase on the acetic acid ketonization over monoclinic zirconia has been investigated using first-principles based density functional theory (DFT) calculations. To capture the aqueous phase chemistry over the solid zirconia catalyst surface, the aqueous phase is represented by 111 explicit water molecules with a liquid water density of 0.93 g/cm3 and the monoclinic zirconia is modeled by the most stable surface structure . The dynamic nature of aqueous phase/ interface was studied using ab initio molecular dynamics simulation, indicating that nearly half of the surface Zr sites are occupied by either adsorbed water molecules or hydroxyl groups at 550 K. DFT calculations show that the adsorption process of acetic acid from the liquid water phase to the surface is nearly thermodynamically neutral with a Gibbs free energy of -2.3 kJ/mol although the adsorption strength of acetic acid on the surface in aqueous phase is much stronger than in vapor phase. Therefore it is expected that the adsorption of acetic acid will dramatically affects aqueous phase ketonization reactivity over the monoclinic zirconia catalyst. Using the same ketonization mechanism via the β-keto acid intermediate, we have compared acetic acid ketonization to acetone in both vapor and aqueous phases. Our DFT calculation results show although the rate-determining step of the β-keto acid formation via the C-C coupling is not pronouncedly affected, the presence of liquid water molecules will dramatically affect dehydrogenation and hydrogenation steps via proton transfer mechanism. This work was financially supported by the United States Department of Energy (DOE)’s Bioenergy Technologies Office (BETO) and performed at the Pacific Northwest National Laboratory (PNNL). PNNL is a multi-program national laboratory operated for DOE by Battelle Memorial Institute. Computing time and advanced catalyst characterization use was granted by a user proposal at the William R. Wiley Environmental Molecular Sciences Laboratory (EMSL). EMSL is a national scientific user facility sponsored by the Department of Energy’s Office of Biological and Environmental Research and located at PNNL.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2017

Enhanced Hydrothermal Stability and Catalytic Activity of LaxZryOz Mixed Oxides for the Ketonization of Acetic Acid in the Aqueous Condensed Phase

Common ketonization catalysts such as ZrO2, CeO2, and TiO2-based catalysts have been reported to lose surface area, undergo phase transformation, and lose catalytic activity when utilized in the condensed aqueous phase. In this work, we synthesized a series of LaxZryOz mixed-metal oxides with different La:Zr atomic ratios with the goal of enhancing the catalytic activity and stability for the ketonization of acetic acid in condensed aqueous media at 568 K. We synthesized a hydrothermally stable LaxZryOz mixed-metal oxide catalyst with ketonization activity360 and 40 times more active than La2O3 and ZrO2, respectively. Catalyst characterization techniques suggest that the enhanced stability of the LaxZryOz catalysts is observed with the formation of a phase isomorphic with tetragonal ZrO2. DRIFT spectroscopy measurements indicated the enhanced catalytic activity of LaxZryOz catalysts correlated with greater acetic acid surface population in the presence of H2O versus pure ZrO2.

ketonization, deoxygenation, carboxylic acid, acet↗

DOE OSTI2017

Systems and processes for conversion of ethylene feedstocks to hydrocarbon fuels

09 BIOMASS FUELS↗

DOE OSTI2017

Systems and processes for conversion of ethylene feedstocks to hydrocarbon fuels

09 BIOMASS FUELS↗

DOE OSTI2014

An Ionic Liquid Reaction and Separation Process for Production of Hydroxymethylfurfural from Sugars

There has been world-wide interest to making plastics out of renewable biomass feedstock for recent years. Hydroxymethylfurfural (HMF) is viewed as an attractive alternate to terephthalic acid (TPA) for production of polyesters (PET) and polyamides. Conversion of sugars into HMF has been studied in numerous publications. In this work, a complete ionic liquid reaction and separation process is presented for nearly stoichiometric conversion of fructose into HMF. Different adsorbent materials are evaluated and silicalite material is demonstrated effective for isolation of 99% pure HMF from actual ionic liquid reaction mixtures and for recovery of the un-converted sugars and reaction intermediate along with the ionic liquid. Membrane-coated silicalite particles are prepared and studied for a practical adsorption process operated at low pressure drops but with separation performances comparable or better than the powder material. Complete conversion of fresh fructose feed into HMF in the recycled ionic liquid is shown under suitable reaction conditions. Stability of HMF product is characterized. A simplified process flow diagram is proposed based on these research results, and the key equipment such as reactor and adsorbent bed is sized for a plant of 200,000 ton/year of fructose processing capacity. The proposed HMF production process is much simpler than the current paraxylene (PX) manufacturing process from petroleum oil, which suggests substantial reduction to the capital cost and energy consumption be possible. At the equivalent value to PX on the molar basis, there can be a large gross margin for HMF production from fructose and/or sugars.

Liu, Wei↗

DOE OSTI2012

Adsorption separation processes for ionic liquid catalytic processes

Presently disclosed are methods and apparatus for separation of reaction products from reaction mixtures in an ionic liquid catalysis process, particularly in conversion of biomass, cellulose, and sugars into chemical intermediates such as 5-hydroxymethylfurfural (HMF). In one embodiment an ion exclusion adsorption mechanism is used for the separation process. The process comprises (i) mixing the ionic liquid-containing reaction mixture with de-ionized water, (ii) flowing the water solution mixture into an adsorption column, (iii) eluting the column with a water- and/or alcohol-based fluid, and (iv) collecting separated fractions at different elution times.

Liu, Wei↗