Engineering topics

Cornelius, Aaron

Publications and source records attributed to Cornelius, Aaron.

4 records

DOE OSTI2025

Optimization of an aerostructural machining process using physics-guided Bayesian stability modelling

Existing algorithms for predicting milling chatter have not been widely adopted in industry since they require specialized instruments to measure the stability inputs. This study describes how the machining process for a meter-scale aluminum aerostructure was optimized using a physics-guided Bayesian stability model. The study was performed in collaboration with an industrial partner on production machines to evaluate the practicality of the proposed method under real-world conditions. For each cutting tool, the Bayesian approach automatically selected a small number of cutting tests, which were monitored using a microphone to observe the chatter frequency. The algorithm learned the system dynamics, cutting forces, and stability map from these test results. A novel algorithm for predicting tool bending stress was incorporated into the test selection algorithm to avoid tool breakage. On average, each set of optimized cutting parameters required less than six tests to identify and were 97% more productive than baseline parameters from the cutting tool manufacturer. The machining program was then further optimized using commercial feedrate scheduling software to remove cutting force spikes and reduce air cutting time. Five components were machined using the optimized process. These results demonstrate the potential for physics-guided Bayesian models to improve productivity in industrial settings.

Cornelius, Aaron [UT Knoxville]↗

DOE OSTI2024

Process damping identification using Bayesian learning and time domain simulation

Process damping can provide improved machining productivity by increasing the stability limit at low spindle speeds. However, existing methods for identifying process damping models experimentally require specialized setups and/or multiple cutting tests. While the phenomenon is well known, the modeling challenges limit pre-process parameter selection that leverages the potential increases in material removal rates. This paper proposes a physics-informed Bayesian method that can identify the cutting force and process damping models from a limited set of test cuts without requiring direct measurements of cutting force or vibration. The method uses time domain simulation to incorporate process damping and provide a basis for test selection. Here, new strategies for efficient sampling and dimensionality reduction are applied to lower computation time and minimize the effect of model error. The proposed method is demonstrated and the identified cutting and damping force coefficients are compared to values obtained using machining tests and least-squares fitting.

42 ENGINEERING↗

DOE OSTI2024

Using GANs to predict milling stability from limited data

Milling is a key manufacturing process that requires the selection of operating parameters that provide efficient performance. However, the presence of chatter, a self-excited vibration causing poor surface finish and potential damage to the machine and cutting tool, makes it challenging to select the appropriate parameters. To predict chatter, stability maps are commonly used, but their generation requires expensive data, making it difficult to employ these maps in industry. Therefore, there is a pressing need for an approach that can accurately predict stability maps using limited experimental data. This study introduces the new Encoder GAN (EGAN) approach based on Generative Adversarial Networks (GANs) that predicts stability maps using limited experimental data. The approach consists of the encoder, generator, and discriminator subnetworks and uses the trained encoder and generator to predict the target stability map. This versatile method can be applied to various tool setups and can accurately predict stability maps with limited experimental data (five to 10 cutting tests) even when there is little information available for unknown parameters. In conclusion, the study evaluates the proposed approach using both numerical data and experiments and demonstrates its superior performance compared to state-of-the-art benchmarks.

42 ENGINEERING↗

DOE OSTI2023

Structured light scanning artifact-based performance study

Structured light scanning is used to create a digital twin of a manufactured part, where features are extracted to determine if the part meets the designer’s intent and required tolerances. This paper describes repeatability and reproducibility analyses for a commercially-available structured light scanning system and measurement artifact. The repeatability study used five repeated scans at 15 measurement positions. Repeatability was assessed by randomly selecting one of the five scans at each of the 15 positions and creating a part mesh. This process was performed 50 times and the statistics for the dimension variations were calculated to isolate the scanning effects only. The same sequence was then performed for 10 of the 15 positions and five of the 15 positions to evaluate the repeatability sensitivity to the number of measurement positions. Reproducibility was assessed by selecting 15 positions to create a mesh and repeating the 15-position measurement sequence 10 times using different positions for each mesh construction. The statistics for the dimension variations were then calculated. This incorporated the effects of both scanning and the position and orientation of the part relative to the scanner. This sequence was repeated for 10-position and five-position scans to evaluate the corresponding sensitivity. Finally, the artifact dimensions from structured light scanning were compared to coordinate measuring machine measurements of the same features.

42 ENGINEERING↗