Search NASA⌕ Search

Engineering topics

Corona, Edmundo

Publications and source records attributed to Corona, Edmundo.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Validation Exercise of a Coarse Finite Element Model of Laser Welds

The objective of this project is to validate low-fidelity models of 304L to 304L stainless steel partial-penetration laser welds for thin sheets. Low-fidelity means that the weld is represented by coarsely meshed element blocks. Here, the hexahedral element size is approx imately half the weld penetration depth. The material behavior of the block is represented by a J2 plasticity model with a Voce hardening function. The source of the data used in this work is an extensive experimental study conducted by Sharlotte Kramer (1528) and published in 2015. Figure 1 shows a cross-section of the weld of interest. The nominal thickness of the sheets is 0.063 in. while the target penetration depth of the weld is in the range of 0.028 to 0.032 in., extending about half the sheet thickness. Uniaxial tension tests provided data for calibration of base material and weld models. Results of two validation geometries were also provided. The principal validation geometry is shown in Fig. 2. It consists of a plate specimen with in-plane dimensions 6 in × 2.875 in loaded in tension. A circular plug with a 1.5 in. diameter was cut from the center of the plate and then welded in place. The details of the welding schedule are given. An important assumption is that the welds in the calibration and validation specimens have similar geometric and material properties as those in the validation tests. The task was to first calibrate models for the base material and the welds and then simulate the validation tests until the point of weld first failure.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Evaluation of 304L stainless steel deformation and failure under cyclic loading

The motivation for this work came from the simulation of components subjected to impact. In these problems, repeated loading can be generated by vibrational motion between internal parts of the component or by the occurrence of multiple impacts. Graphs of tensile equivalent plastic strain $(\overline{\varepsilon}_T^\rho)$ versus time from such cases had the character shown in Fig. 1. The equivalent plastic strain grew by alternating periods of accumulation and hold. The periods of hold indicate times when $d\overline{\varepsilon}_T^\rho$ did not accumulate. This can be due to the material unloading into the elastic range, or actually plastically reverse loading with hydrostatic stress σ h < 0 as was demonstrated for an impact simulation. Similar observations were made from the simulation of a 2-degree-of-freedom mass-elastic-plastic-spring system subjected to impact.

36 MATERIALS SCIENCE↗
DOE OSTI2023

FY23 Simulation of Elastic-Plastic Failure Propagation

This memo summarizes the simulation of ductile failure propagation work conducted under the ASC project “V&V of Ductile Failure” conducted during FY 23. Physically, the failure propagation consists of crack propagation in the material. In the numerical setting—specifically in a finite element model—propagation can be accomplished through element death when critical conditions occur locally at an element that is then deleted from the simulation. The validation of the finite element models is evaluated by direct comparison between the experimental and simulation results regarding the rate of crack growth and its influence on the load-deflection response of the specimens tested. This work considers two geometries that display stable crack propagation under displacement-controlled conditions. The first geometry consists of hat specimens loaded in compression with nominally identical geometries but made with three different materials: Steel A286, Al 7075-T651 and 304L stainless steel. The three materials represent a range of ductility values that affect the response and crack propagation within the specimen. The crack induced propagates under an essentially mode-II type of deformation. The second geometry consists of a pre-cracked 304L stainless steel compact tension test specimen loaded so as to induce a mode-I deformation at the crack.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Sandia Mechanics Challenge 2023 Information Packet: Structure with a Threaded Fastener Joint

The Sandia Mechanics Challenge (SMC) provides the solid-mechanics community a forum for assessing its ability to predict mechanical behavior in structures and materials through a blind, round-robin format. Computationalists are asked to predict the behavior of an unfamiliar geometry given experimental calibration data, their predictions are compared to experimental measurements of the SMC scenario, and then the participants assess and compare their approaches, documenting their findings. The SMC broadens the scope of Sandia-hosted benchmarking problems that previously focused on ductile failure through the Sandia Fracture Challenges, enabling an enduring, community-wide self-assessment of predictive capabilities for a variety of mechanics topics. The SMC is part of the Structural Reliability Partnership, which offers other benchmarking challenges hosted by several participating institutions.

42 ENGINEERING↗
DOE OSTI2022

Validation of material models for puncture of 7075-T651 aluminum plate

Plate puncture simulations are challenging computational tasks that require advanced material models including high strain rate and thermal-mechanical effects on both deformation and failure, plus finite element techniques capable of representing large deformations and material failure. The focus of this work is on the material issues, which require large sets of experiments, flexible material models and challenging calibration procedures. In this study, we consider the puncture of 12.7 mm thick, 7075-T651 aluminum alloy plates by a cylindrical punch with a hemispherical nose and diameter of 12.7 mm. The plasticity and ductile failure models were isotropic with calibration data obtained from uniaxial tension tests at different temperatures and strain rates plus quasi-static notched tension tests and shear-dominated tests described here. Sixteen puncture experiments were conducted to identify the threshold penetration energy, mode of puncture and punch acceleration during impact, The punch was mounted on a 139 kg mass and dropped on the plates with different impact speeds. Since the mass was the same in all tests, the quantity of interest was the impact speed. The axis and velocity of the punch were perpendicular to the plate surface. The mean threshold punch speed was 3.05 m/s, and the mode of failure was plugging by thermal-mechanical shear banding accompanied by scabbing fragments. Application of the material models in simulations of the tests yielded accurate estimates of the threshold puncture speed and of the mode of failure. Time histories of the punch acceleration compared well between simulation and test. Remarkably, the success of the simulations occurred in spite of even the smallest element used being larger than the width of the shear bands.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Mass Property Calculator

A mass property calculator has been developed to compute the moment of inertia properties of an assemblage of parts that make up a system. The calculator can take input from spreadsheets or Creo mass property files or it can be interfaced with Phoenix Integration Model Center. The input must include the centroidal moments of inertia of each part with respect to its local coordinates, the location of the centroid of each part in the system coordinates and the Euler angles needed to rotate from the part coordinates to the system coordinates. The output includes the system total mass, centroid and mass moment of inertia properties. The input/output capabilities allow the calculator to interface with external optimizers. In addition to describing the calculator, this document serves as its user's manual. The up-to-date version of the calculator can be found in the Git repository https://cee-gitlab.sandia.gov/cj?ete/mass-properties-calculator.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2021

Rate and temperature independent model calibrations for J2 plasticity and Wilkins failure models for 17-4PH H1150 stainless steel

This memo’s objective is to report a calibration of the J2 plasticity model with the Wilkins ductile failure criterion for 17-4 PH H1150 stainless steel under slow loading at room temperature. The calibration of the hardening function was based on uniaxial tension tests, while that of the failure model included data from tension tests on notched specimens, a butterfly specimen shear test, and a set of interrupted compression tests on shear hat specimens. The procedure was that described in, minus the rate and temperature dependence.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Effects of finite element discretization and model simplification on calculations of ductile failure initiation

The finite element method is a scheme to discretize the infinite number of degrees of freedom in continuum-level problems down to a finite number of degrees of freedom. This discretization is done in conjunction with methods that also reduce the field differential equations to sets of algebraic ones that can be solved by arithmetical operations. Therefore, solutions attained by finite element models are approximations to the exact solutions of the field equations.

97 MATHEMATICS AND COMPUTING↗