Search NASA⌕ Search

Engineering topics

Coverdale, C A

Publications and source records attributed to Coverdale, C A.

Planar Wire-Array Z-Pinch Implosion Dynamics and X-Ray Scaling at Multiple-MA Drive Currents for a Compact Multisource Hohlraum Configuration

An indirect drive configuration is proposed wherein multiple compact Z-pinch x-ray sources surround a secondary hohlraum. Planar compact wire arrays allow reduced primary hohlraum surface area compared to cylindrical loads. Implosions of planar arrays are studied at up to 15 TW x-ray power on Saturn with radiated yields exceeding the calculated kinetic energy, suggesting other heating paths. X-ray power and yield scaling studied from 1-6 MA motivates viewfactor modeling of four 6-MA planar arrays producing 90 eV radiation temperature in a secondary hohlraum.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Studying Radiation from Z-pinch Wire Array and X-Pinch Plasmas: K-shell Mg to M-shell Mo

University-scale Z-pinch generators are able to produce plasmas with a broad range of temperatures, densities, and opacity properties depending on the type, size, and mass of wire-array loads and wire materials. Experiments with very different Z-pinch loads were performed on the 1 MA Zebra generator at UNR and analyzed during the last five years including Single and Nested Cylindrical, Conical, and various types of Planar Wire Arrays. It is shown that such wire arrays are good sources of x-rays and that they produce significant radiation yield (up to 25 kJ) on a ns time scale, and generate bright spots of sub-mm size. They can be used for studying radiative properties of moderate density (between 10{sup 18} cm{sup -3} and 5x10{sup 21} cm{sup -3}) and temperature (<=1.5 keV) plasmas. In addition, X-pinches generated higher density (>10{sup 22} cm{sup -3}) and temperature (>2 keV) plasmas on scales as small as a few mum to several mm in size. Wire materials with a broad range of nuclear charge Z were used, ranging from low-Z, such as alloyed Al wires with varying concentrations of Mg, to mid-Z, such as Stainless steel, Cu, Brass, and Mo. Uniform (made from one wire material) as well as combined (made from two wire materials with almost equal wire masses) wire arrays were considered. Uniform, combined, symmetric and asymmetric X-pinches (some of which included a small fraction of tracer Al wires) were also considered. Non-LTE kinetic models to account for K- and L-shell radiation were employed to understand radiative properties of Z-pinch and X-pinch plasmas. Implosion characteristics of such loads are discussed using the wire dynamics and MHD models. Opacity effects of Z-pinch plasmas are studied and benefits of using alloyed and tracer wires are highlighted.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Absolute x-ray yields from laser-irradiated germanium-doped low-density aerogels

The x-ray yields from laser-irradiated germanium-doped ultra-low-density aerogel plasmas have been measured in the energy range from sub-keV to {approx_equal}15 keV at the OMEGA laser facility at the Laboratory for Laser Energetics, University of Rochester. The targets' x-ray yields have been studied for variation in target size, aerogel density, laser pulse length, and laser intensity. For targets that result in plasmas with electron densities in the range of {approx_equal}10% of the critical density for 3{omega} light, one can expect 10-11 J/sr of x rays with energies above 9 keV, and 600-800 J/sr for energies below 3.5 keV. In addition to the x-ray spectral yields, the x-ray temporal waveforms have been measured and it is observed that the emitted x rays generally follow the delivered laser power, with late-time enhancements of emitted x-ray power correlated with hydrodynamic compression of the hot plasma. Further, the laser energy reflected from the target by plasma instabilities is found to be 2%-7% of the incident energy for individual beam intensities {approx_equal}10{sup 14}-10{sup 15} W/cm{sup 2}. The propagation of the laser heating in the target volume has been characterized with two-dimensional imaging. Source-region heating is seen to be correlated with the temporal profile of the emitted x-ray power.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Observation of >400-eV Precursor Plasmas from Low-Wire-Number Copper Arrays at the 1-MA Zebra Facility

Experiments with cylindrical copper wire arrays at the 1-MA Zebra facility show that high temperatures exist in the precursor plasmas formed when ablated wire array material accretes on the axis prior to the stagnation of a z pinch. In these experiments, the precursor radiated approximately 20% of the >1000 eV x-ray output, and time-resolved spectra show substantial emission from Cu L-shell lines. Modeling of the spectra shows an increase in temperature as the precursor forms, up to {approx}450 eV, after which the temperature decreases to {approx}220-320 eV until the main implosion.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Absolute X-Ray Yields From Laser-Irradiated Ge-Doped Low-Density Aerogels

We have used the OMEGA laser (Laboratory for Laser Energetics, University of Rochester) to measure the X-ray yields from laser-irradiated germanium-doped ultra-low-density aerogel plasmas in the energy range from sub-keV to {approx} 15 keV. They have studied the targets X-ray yields with variation in target size, aerogel density, laser pulse length and laser intensity. For targets that result in plasmas with electron densities in the range of {approx} 10% of the critical density for 3{omega} light, one can expect 10-11 J/sr of X-rays with energies above 9 keV, and 600-800 J/sr for energies below 3.5 keV. In addition to the X-ray spectral yields, they have measured the X-ray temporal waveforms and found that the emitted X rays generally follow the delivered laser power, with late-time enhancements of emitted X-ray power correlated with hydrodynamic compression of the hot plasma. Also, they find the laser energy reflected from the target by plasma instabilities to be 2-7% of the incident energy for individual beam intensities {approx} 10{sup 14}-10{sup 15} W/cm{sup 2}. They also have characterized the propagation of the laser heating in the target volume with two-dimensional imaging. They find the source-region heating to be correlated with the temporal profile of the emitted X-ray power.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Planar Wire Array Dynamics and Radiation Scaling at Multi-MA Levels on the Saturn Pulsed Power Generator

Planar wire arrays are studied at 3-6 MA on the Saturn pulsed power generator as potential drivers of compact hohlraums for inertial confinement fusion studies. Comparison with zero-dimensional modeling suggests that there is significant trailing mass. The modeled energy coupled from the generator cannot generally explain the energy in the main x-ray pulse. Preliminary comparison at 1-6 MA indicates sub-quadratic scaling of x-ray power in a manner similar to compact cylindrical wire arrays. Time-resolved pinhole images are used to study the implosion dynamics.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Radiative Properties of Implosions of Stainless Steel Wire Arrays with Application to Astrophysics

Experiments with different stainless steel (SS) wire loads were performed on the 1 MA Zebra Z-pinch generator at University of Nevada, Reno. The wire array loads consisted of 7.6 {mu}m SS wires and had 10 wires for the planar wire array with an interwire gap of 1 mm and 8 wires for the cylindrical wire array of a 16 mm diameter. In addition, a single-wire experiment with a 25 {mu}m SS wire was carried out. The different wire loads were used to provide a broader spectrum of plasma conditions. Time-integrated and time-gated x-ray images, as well as time-integrated, spatially-resolved and spatially-integrated x-ray spectra, were collected and analyzed. Both K-shell and L-shell radiation were recorded using LiF and KAP crystal spectrometers, respectively. Non-LTE kinetic models of Fe and Ni are employed to derive plasma parameters. For axially resolved L-shell spectra, the resulting electron temperatures are between 230 and 300 eV (higher near the cathode) and electron densities vary from 10{sup 19} to 10{sup 20} cm{sup -3} dependent on the load. The advantage of using Z-pinch plasmas for astrophysical applications is highlighted.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

2D Radiation MHD K-shell Modeling of Single Wire Array Stainless Steel Experiments on the Z Machine

Many physical effects can produce unstable plasma behavior that affect K-shell emission from arrays. Such effects include: asymmetry in the initial density profile, asymmetry in power flow, thermal conduction at the boundaries, and non-uniform wire ablation. Here we consider how asymmetry in the radiation field also contributes to the generation of multidimensional plasma behavior that affects K-shell power and yield. To model this radiation asymmetry, we have incorporated into the MACH2 r-z MHD code a self-consistent calculation of the non-LTE population kinetics based on radiation transport using multi-dimensional ray tracing. Such methodology is necessary for modeling the enhanced radiative cooling that occurs at the anode and cathode ends of the pinch during the run-in phase of the implosion. This enhanced radiative cooling is due to reduced optical depth at these locations producing an asymmetric flow of radiative energy that leads to substantial disruption of large initial diameter (>5 cm) pinches and drives 1D into 2D fluid (i.e., Rayleigh-Taylor like) flows. The impact of this 2D behavior on K-shell power and yield is investigated by comparing 1D and 2D model results with data obtained from a series of single wire array stainless steel experiments performed on the Z generator.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Overview of 12-cm-Diameter, Argon Gas-Puff Experiments and Analyses with >200-ns Implosion Times at 3- to 6-MA Peak Currents

This paper reviews the motivation for, results from, and analyses of 12-cm-diameter argon gas-puff experiments carried out over the last four years on three generators at 3.2- to 6.5-MA peak currents, all with implosion times {>=}200 ns. Using the argon K-shell yield as a metric of implosion quality, high-quality implosions are obtained for an appropriate initial radial mass distribution, i.e., a distribution that is peaked on axis. Higher compressed densities and smaller final radii are observed compared to shell-like initial mass distributions. Theory and data suggest that these distributions mitigate the magnetic Rayleigh-Taylor instability. An energy analysis shows that (1) significant electrical energy is directly coupled to the pinch during the K-shell radiation pulse and (2) conversion of radially-directed kinetic energy into thermal energy is not the dominant mechanism responsible for the pinch K-shell radiation.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Properties of the Best Ar K-Shell Radiators: Two Decades of Data Analysis from Seven Z-Pinch Drivers

Z Pinches formed from Ar gas puffs have been investigated for more than two decades. Experiments have been performed on many generators; a frequent objective has been maximization of the yield in the K-shell lines. The increase in available current during that time, from 2 to 15 MA, has resulted in a remarkable enhancement in yield from a few kJ on PITHON to {approx}300 kJ on Sandia's Z generator. We have analyzed spectroscopic and other radiation data from seven Z-pinch drivers, some dating back to 1991, in an effort to determine what properties of the pinches correlate with high K-shell yield. The strongest correlation is with the amount of mass that is heated to K-shell emitting temperatures. Those temperatures, effective at emitting Ar K-shell x rays, exhibit a range of {approx}1 to 2.4 keV.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Radiation Hydrodynamics of Stainless Steel Wire Arrays on the Z Accelerator

Experiments on the Z accelerator with nested stainless steel wire arrays produced K-shell x-ray yields exceeding 50 kJ in the energy range 5.5 to 8 keV. Stainless steel (Z = 24-28) can barely be ionized to the K-shell on Z, and the spectra are therefore sensitive to the details of the implosion. We have simulated the implosion dynamics of stainless steel wire arrays with diameters ranging from 4.5 to 8.0 centimeters using a detailed configuration non-LTE radiation hydrodynamics model. Reasonable agreement with total and K-shell experimental yields was obtained for the various array configurations. A comparison is made between the 1-D and 2-D simulations for shot Z-578.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

1D Scaling with Ablation for K-Shell Radiation from Stainless Steel Wire Arrays

A 1D Lagrangian magnetohydrodynamic z-pinch simulation code is extended to include wire ablation. The plasma transport coefficients are calibrated to reproduce the K-shell yields measured on the Z generator for three stainless steel arrays of diameter 55 mm and masses ranging from 1.8 to 2.7 mg. The resulting 1D scaling model is applied to a larger SS array (65 mm and 2.5 mg) on the refurbished Z machine. Simulation results predict a maximum K-shell yield of 77 kJ for an 82 kV charging voltage. This maximum drops to 42 kJ at 75 kV charging. Neglecting the ablation precursor leads to a {approx}10% change in the calculated yield.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

X-ray diagnostics of imploding plasmas from planar wire arrays composed of Cu and few tracer Al wires on the 1MA pulsed power generator at UNR

Tracer aluminum alloyed wires (Al5056) are used to provide additional information for x-ray diagnostics of implosions of Cu planar wire arrays (PWAs). Specifically, the analysis of combined PWA experiments using the extensive set of x-ray diagnostics is presented. In these experiments, which were conducted at the 1MA pulsed power generator at University of Nevada, Reno, the Z-pinch load consisted of several (eight) Cu alloyed (main material) and one to two Al alloyed (tracer) wires mounted in a single plane row or double parallel plane rows, single planar wire array (SPWA) or double planar wire array (DPWA), respectively. The analysis of x-ray spatially resolved spectra from the main material indicates the increase in the electron temperature T{sub e} near the cathode. In general, the axial gradients in T{sub e} are more pronounced for SPWA than for DPWA due to the more 'columnlike' plasma formation for SPWA compared to 'hot-spot-like' plasma formation for DPWA. In addition, x-ray spectra from tracer wires are studied, and estimated plasma parameters are compared with those from the main material. It is observed that the x-ray K-shell Al spectra manifest more opacity features for the case of SPWA with about 18% of Al mass (to the total load mass) compared to the case of DPWA with about 11% of Al mass. The analysis of time-gated spectra shows that the relative intensity of the most intense K-shell Al line, small before the x-ray burst, increases with time and peaks close to the maximum of the sub-keV signal.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Multicolor, time-gated, soft x-ray pinhole imaging of wire array and gas puff Z pinches on the Z and Saturn pulsed power generators

A multicolor, time-gated, soft x-ray pinhole imaging instrument is fielded as part of the core diagnostic set on the 25 MA Z machine [M. E. Savage et al., in Proceedings of the Pulsed Power Plasma Sciences Conference (IEEE, New York, 2007), p. 979] for studying intense wire array and gas puff Z-pinch soft x-ray sources. Pinhole images are reflected from a planar multilayer mirror, passing 277 eV photons with <10 eV bandwidth. An adjacent pinhole camera uses filtration alone to view 1-10 keV photons simultaneously. Overlaying these data provides composite images that contain both spectral as well as spatial information, allowing for the study of radiation production in dense Z-pinch plasmas. Cu wire arrays at 20 MA on Z show the implosion of a colder cloud of material onto a hot dense core where K-shell photons are excited. A 528 eV imaging configuration has been developed on the 8 MA Saturn generator [R. B. Spielman et al., and A. I. P. Conf, Proc. 195, 3 (1989)] for imaging a bright Li-like Ar L-shell line. Ar gas puff Z pinches show an intense K-shell emission from a zippering stagnation front with L-shell emission dominating as the plasma cools.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Double planar wire array as a compact plasma radiation source

Magnetically compressed plasmas initiated by a double planar wire array (DPWA) are efficient radiation sources. The two rows in a DPWA implode independently and then merge together at stagnation producing soft x-ray yields and powers of up to 11.5 kJ/cm and more than 0.4 TW/cm, higher than other planar arrays or low wire-number cylindrical arrays on the 1 MA Zebra generator. DPWA, where precursors form in two stages, produce a shaped radiation pulse and radiate more energy in the main burst than estimates of implosion kinetic energy. High radiation efficiency, compact size (as small as 3-5 mm wide), and pulse shaping show that the DPWA is a potential candidate for ICF and radiation physics research.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Measurement of Temperature, Density, and Particle Transport with Localized Dopants in Wire-Array Z Pinches

Axially localized NaF dopants are coated onto Al cylindrical wire arrays in order to act as spectroscopic tracers in the stagnated z-pinch plasma. Non-local-thermodynamic-equilibrium kinetic models fit to Na K-shell lines provide an independent measurement of the density and temperature that is consistent with spectroscopic analysis of K-shell emissions from Al and an alloyed Mg dopant. Axial transport of the Na dopant is observed, enabling quantitative study of instabilities in dense z-pinch plasmas.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Large diameter (45-80 mm) nested stainless steel wire arrays at the Z accelerator

Experiments have been performed at the Z accelerator to elucidate the effects of initial load diameter on the radiated output of a 7 keV wire array x-ray source. Nested wire arrays with initial outer diameters of 45-80 mm were fielded, with the masses chosen to maintain a nominally constant coupling to the Z generator. The total radiated output decreased from {approx}1.1 MJ to <0.5 MJ for the largest diameter arrays, while the >1 keV and K-shell radiation decreased at both small and large diameters. The >1 keV output peaked at {approx}340 kJ, while the K-shell yield peaked at {approx}55 kJ. The observed trends in radiated output and stagnated plasma parameters are consistent with a phenomenological K-shell scaling theory, and are reproduced in one-dimensional modeling, although multidimensional effects, such as, growth of the Rayleigh-Taylor instability, are observed in the experiments and appear to impact the stagnated plasma for the larger diameter arrays.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗