Engineering topics

Craig, Larry

Publications and source records attributed to Craig, Larry.

5 records

NASA NTRS2002

Predicting Print-thru for the Sub-scale Beryllium Mirror Demonstrator (SBMD)

This document presents a finite element method for predicting print-thru or quilting for a lightweight mirror in a low temperature environment. The mirror is represented with quadrilateral and triangular plate finite elements. The SBMD (Sub-scale Beryllium Mirror Demonstrator) is circular with a diameter of 50 cm and one flat side. The mirror structure is a thin-wall triangular cell core with a single facesheet. There is a 4 mm radius fillet between the facesheet and cell walls. It is made entirely of Beryllium. It is assumed that polishing the mirror surface creates a thin surface layer with different material properties. Finite element results are compared with measured values at cryogenic temperatures.

Craig, Larry↗

NASA NTRS2001

Structural Analysis of a 50 cm Diameter Open-Back Triangular Cell Beryllium Mirror in a Cryogenic Environment

This paper discusses NASTRAN structural analysis of the Sub-Scale Beryllium Mirror Demonstrator (SBMD), which has been developed by Ball Aerospace as an experimental design concept for the Next Generation Space Telescope (NGST). The mirror was repeatedly subjected to 35K environment in the large cryogenic test chamber at Marshall Space Flight Center (MSFC). Deformations on the mirror surface were measured optically. The surface distortions predicted by NASTRAN are analyzed optically for comparison with the measured values. Model results compare favorably with measured results for an ambient temperature validation case. For the cryogenic environment case the influence of geometry and material property variations is being investigated to obtain closer correlation.

Craig, Larry↗

NASA NTRS2001

Structural Analysis of a 50 cm Diameter Open-back Triangular Cell Beryllium Mirror in a Cryogenic Environment

This paper discusses NASTRAN structural analysis of the Sub-Scale Beryllium Mirror Demonstrator (SBMD), which has been developed by Ball Aerospace as an experimental design concept for the Next Generation Space Telescope (NGST). The mirror was repeatedly subjected to 35 K environment in the large cryogenic test chamber at Marshall Space Flight Center. Deformations on the mirror surface were measured optically. The surface distortions predicted by NASTRAN are analyzed optically for comparison with the measured values. Model results compare favorably with measured results for ambient temperature validation cases. For the cryogenic environment case the influence of geometry and material property variations is being investigated to obtain closer correlation.

Craig, Larry↗

NASA NTRS2000

Finite Element Modeling of a Semi-Rigid Hybrid Mirror and a Highly Actuated Membrane Mirror as Candidates for the Next Generation Space Telescope

Advanced space telescopes, which will eventually replace the Hubble Space Telescope (HTS), will have apertures of 8 - 20 n. Primary mirrors of these dimensions will have to be foldable to fit into the space launcher. By necessity these mirrors will be extremely light weight and flexible and the historical approaches to mirror designs, where the mirror is made as rigid as possible to maintain figure and to serve as the anchor for the entire telescope, cannot be applied any longer. New design concepts and verifications will depend entirely on analytical methods to predict optical performance. Finite element modeling of the structural and thermal behavior of such mirrors is becoming the tool for advanced space mirror designs. This paper discusses some of the preliminary tasks and study results, which are currently the basis for the design studies of the Next Generation Space Telescope.

Craig, Larry↗

NASA NTRS1998

Design of Large Lightweight Space Telescope Optical Systems for the Next Generation Space Telescope

The Next Generation Space Telescope (NGST) is currently in a Pre Phase A study effort to prove feasibility of design and to show that the design can be implemented within cost constraint guidelines and meet the requirements of the science community. In an effort to achieve the science communities goals as outlined in "HST and Beyond" the NGST team has developed a government "yardstick" design of an eight meter diameter segmented telescope which would be launched in an Atlas IIAS launch vehicle to a L2 (Lagrange Point) orbit. This paper will discuss the design of the Optical Telescope Assembly (OTA) and the various issues and complications of designing lightweight optics to be placed in the environment that the NGST will encounter both during launch and during its operational mission at L2. The OTA must be lightweight but structurally must withstand the launch environment and transfer to its final L2 orbit. The OTA must be stable at L2 to provide high quality science at the cryogenic temperatures it will experience. The OTA segmented petal concept is to develop lightweight optics which can either be manipulated to achieve and maintain a desired figure or be rigid enough so that change in shape is only necessary for phasing and alignment. The secondary mirror structural mast must also be rigid with frequency responses which are not coupled to spacecraft modes in order to maintain and decenter and despace requirements.

Jacobson, Dave↗