Engineering topics
Craig, Scott
Publications and source records attributed to Craig, Scott.
Guidance, Navigation, and Control for NASA Lunar Pallet Lander
The NASA Lander Technology project is leading the development and integration of the Lunar Pallet Lander (LPL) concept. The objective is to demonstrate precision landing by delivering a payload to the lunar surface within 100 meters of a landing target. Potential landing sites are selected near the lunar pole where water may be present in permanently shadowed regions that could enable future in-situ resource utilization. The LPL is part of a sequence of missions aimed at maturing the necessary technologies, such as lunar precision landing sensors, that will enable the next generation of multi-ton lunar payloads and human landers. This paper provides an overview of the Mission Design, Guidance Navigation and Control (GNC) algorithms, and sensor suite. The results show the LPL simulated trajectory and landing precision performance under nominal and dispersed conditions. The landing precision simulation confirms the need to rely on high-accuracy navigation techniques and sensors such as Terrain Relative Navigation (TRN) and the Navigation Doppler Lidar (NDL), currently being developed for space applications. The results also demonstrate the ability of the guidance and control system to perform a soft lunar touchdown by combining thrust vector control during the solid rocket motor deceleration phase, and pulse engine control, for the liquid powered descent phase.
NASA Exploration Mission 2 Mission Design
Exploration Mission 2 (EM-2) will be NASA’s first manned flight on the Space Launch System (SLS) and Orion Spacecraft. The mission has been changed from an SLS Block 1B configuration to Block 1. This change has necessitated a reexamination of the flight profile to determine what changes must be made in order to accommodate the reduced launch vehicle performance on the Block 1. Launch availability and orbital debris risk will be traded to find the best flight profile for both SLS and Orion.
Mission Design for the Lunar Pallet Lander
Due to lighting conditions, the program decided to only fly to the north pole in June 2022 and south pole in December 2022. Starting with the June 2022 landing sites at the north pole, a trajectory scan was run for one landing per day for the latitudes from 85 up to 88 degrees at 0.5 degree increments. Each landing site was at lunar dawn, which determined the landing site’s longitude as described in the previous section. The results of the June 2022 scan showed that LPL had the capability to reach a landing site at least once per day for the region examined as see in in Figure 12. There appears to be a correlation between the landing site’s altitude and the propellant remaining above the lander’s FPR, Figure 13. This is most likely due to the >10 km altitude constraint at SRM burnout. This constraint was applied to keep the lander high above the lunar terrain to avoid mountains, but can be relaxed when the full terrain data is added. Figure 12. June 2022 Nominal Usable Propellant Remaining vs Landing Date/time Similarly, the December 2022 landing sites were run showing that LPL was also capable of reaching a landing site at the Moon at least once per day. Figure 14 shows the results of the December scan, however, there were 3 landing sites that LPL could not reach. Two were very low in altitude (-5 and -4 km in altitude), which looking at the altitude trends in Figure 15, indicates that these sites may not be feasible with the current mission design. It may be possible to achieve the low altitude landing sites by lowering the SRM burnout altitude constraint, but that requires detailed terrain modeling, planned for a future phase of the analysis. The third non-reachable landing site is most likely due to an optimization error, as its altitude was high enough, at -2 km, that it should not have been a problem for the lander to arrive there. More analysis is required to verify this observation.
Combining Simulation Tools for End-to-End Trajectory Optimization
Trajectory simulations with advanced optimization algorithms are invaluable tools in the process of designing spacecraft. Due to the need for complex models, simulations are often highly tailored to the needs of the particular program or mission. NASA's Orion and SLS programs are no exception. While independent analyses are valuable to assess individual spacecraft capabilities, a complete end-to-end trajectory from launch to splashdown maximizes potential performance and ensures a continuous solution. In order to obtain end-to-end capability, Orion's in-space tool (Copernicus) was made to interface directly with the SLS's ascent tool (POST2) and a new tool to optimize the full problem by operating both simulations simultaneously was born.