Engineering topics

Cramer, K. E.

Publications and source records attributed to Cramer, K. E..

9 records

NASA NTRS2015

Non-destructive Evaluation of Bonds Between Fiberglass Composite and Metal

To assess the integrity and reliability of an adhesive joint in an automotive composite component, several non-destructive evaluation (NDE) methodologies are correlated to lap shear bond strengths. A glass-fabric-reinforced composite structure was bonded to a metallic structure with a two-part epoxy adhesive. Samples were subsequently cut and tested in shear, and flaws were found in some areas. This study aims to develop a reliable and portable NDE system for service-level adhesive inspection in the automotive industry. The results of the experimental investigation using several NDE methods are presented and discussed. Fiberglass-to-metal bonding is the ideal configuration for NDE via thermography using excitation with induction heating, due to the conductive metal and non-conductive glass-fiber-reinforced composites. Excitation can be either by a research-grade induction heater of highly defined frequency and intensity, or by a service-level heater, such as would be used for sealing windshields in a body shop. The thermographs thus produced can be captured via a high-resolution infrared camera, with principal component analysis and 2D spatial Laplacian processing. Alternatively, the thermographs can be captured by low resolution thermochromic microencapsulated liquid crystal film imaging, which needs no post-processing and can be very inexpensive. These samples were also examined with phased-array ultrasound. The NDE methods are compared to the lap shear values and to each other for approximate cost, accuracy, and time and level of expertise needed.

Zhao, Selina↗

NASA NTRS2010

A Method For The Verification Of Wire Crimp Compression Using Ultrasonic Inspection

The development of a new ultrasonic measurement technique to assess quantitatively wire crimp terminations is discussed. The amplitude change of a compressional ultrasonic wave propagating at right angles to the wire axis and through the junction of a crimp termination is shown to correlate with the results of a destructive pull test, which is a standard for assessing crimp wire junction quality. To demonstrate the technique, the case of incomplete compression of crimped connections is ultrasonically tested, and the results are correlated with pull tests. Results show that the nondestructive ultrasonic measurement technique consistently predicts good crimps when the ultrasonic transmission is above a certain threshold amplitude level. A quantitative measure of the quality of the crimped connection based on the ultrasonic energy transmitted is shown to respond accurately to crimp quality. A wave propagation model, solved by finite element analysis, describes the compressional ultrasonic wave propagation through the junction during the crimping process. This model is in agreement within 6% of the ultrasonic measurements. A prototype instrument for applying this technique while wire crimps are installed is also presented. The instrument is based on a two-jaw type crimp tool suitable for butt-splice type connections. A comparison of the results of two different instruments is presented and shows reproducibility between instruments within a 95% confidence bound.

Cramer, K. E.↗

NASA NTRS2005

The Application of Infrared Thermographic Inspection Techniques to the Space Shuttle Thermal Protection System

The Nondestructive Evaluation Sciences Branch at NASA s Langley Research Center has been actively involved in the development of thermographic inspection techniques for more than 15 years. Since the Space Shuttle Columbia accident, NASA has focused on the improvement of advanced NDE techniques for the Reinforced Carbon-Carbon (RCC) panels that comprise the orbiter s wing leading edge. Various nondestructive inspection techniques have been used in the examination of the RCC, but thermography has emerged as an effective inspection alternative to more traditional methods. Thermography is a non-contact inspection method as compared to ultrasonic techniques which typically require the use of a coupling medium between the transducer and material. Like radiographic techniques, thermography can be used to inspect large areas, but has the advantage of minimal safety concerns and the ability for single-sided measurements. Principal Component Analysis (PCA) has been shown effective for reducing thermographic NDE data. A typical implementation of PCA is when the eigenvectors are generated from the data set being analyzed. Although it is a powerful tool for enhancing the visibility of defects in thermal data, PCA can be computationally intense and time consuming when applied to the large data sets typical in thermography. Additionally, PCA can experience problems when very large defects are present (defects that dominate the field-of-view), since the calculation of the eigenvectors is now governed by the presence of the defect, not the "good" material. To increase the processing speed and to minimize the negative effects of large defects, an alternative method of PCA is being pursued where a fixed set of eigenvectors, generated from an analytic model of the thermal response of the material under examination, is used to process the thermal data from the RCC materials. Details of a one-dimensional analytic model and a two-dimensional finite-element model will be presented. An overview of the PCA process as well as a quantitative signal-to-noise comparison of the results of performing both embodiments of PCA on thermographic data from various RCC specimens will be shown. Finally, a number of different applications of this technology to various RCC components will be presented.

Cramer, K. E.↗

NASA NTRS1995

New nondestructive techniques for the detection and quantification of corrosion in aircraft structures

An overview is presented of several techniques under development at NASA Langley Research Center for detection and quantification of corrosion in aircraft structures. The techniques have been developed as part of the NASA Airframe Structural Integrity Program. The techniques focus on the detection of subsurface corrosion in thin laminated structures. Results are presented on specimens with both manufactured defects, for calibration of the techniques, and on specimens removed from aircraft.

Winfree, W. P.↗

NASA NTRS1992

Thermographic characterization of stress during crack growth

A full-field-thermographic technique for imaging stress patterns in dynamically loaded structures using general purpose IR imaging and image processing hardware is described. The inspection technique is based on the thermoelastic effect. A simple geometry is examined, and the experimentally determined values for the stress invariant are shown to be consistent with theoretical and numerical calculations. The application of full-field-thermographic measurement would ensure that the observed stress field has a common sampling period, thus allowing the observation of rapidly occurring stress anomalies such as the propagation of a fatigue crack. Fatigue crack propagation in two consecutive thermoelastic stress images from an aluminum sample is shown.

Cramer, K. E.↗

NASA NTRS1992

Thermographic imaging of cracks in thin metal sheets

The presence of cracks significantly decreases the structural integrity of thin metal sheets used in aerospace applications. Thermographic detection of surface temperature variations due to these cracks is possible after external heating. An approximate line source of heat is used to produce an inplane flow of heat in the sheet. A crack in the sheet perturbs the inplane flow of heat and can be seen in an image of the surface temperature of the sheet. An effective technique for locating these perturbations is presented which reduces the surface temperature image to an image of variations in the inplane heat flow. This technique is shown to greatly increase the detectability of the cracks. This thermographic method has advantages over other techniques in that it is able to remotely inspect a large area in a short period of time. The effectiveness of this technique depends on the shape, position and orientation of the heat source with respect to the cracks as well as the extent to which the crack perturbs the surface heat flow. The relationship between these parameters and the variation in the heat flow is determined both by experimental and computational techniques. Experimental data is presented for through-the-thickness, subsurface and surface EDM notches. Data for through-the-thickness fatigue cracks are also presented.

Cramer, K. E.↗

NASA NTRS1992

Processing infrared images of aircraft lapjoints

Techniques for processing IR images of aging aircraft lapjoint data are discussed. Attention is given to a technique for detecting disbonds in aircraft lapjoints which clearly delineates the disbonded region from the bonded regions. The technique is weak on unpainted aircraft skin surfaces, but can be overridden by using a self-adhering contact sheet. Neural network analysis on raw temperature data has been shown to be an effective tool for visualization of images. Numerical simulation results show the above processing technique to be an effective tool in delineating the disbonds.

Syed, Hazari↗

NASA NTRS1991

Thermographic detection of cracks in thin sheets

A thermographic inspection technique for crack detection based on a 2D filter convolved with the thermal temperature images is presented. The filter is designed to approximate operating on the temperature images with a Laplacian operator. This operation yields an image which approximates changes in the heat flux in a thin plate. This filtering method results in an enhanced contrast due to the presence of cracks. Measurements have been performed on samples with fabricated electrical discharge machining (EDM) notches (both through-the-thickness and surface notches) and closed fatigue cracks around rivets. It is shown that the technique is effective for the detection of various crack lengths down to the resolution limits of the imager used.

Cramer, K. E.↗

NASA NTRS1991

Thermographic inspection of fatigue cracks in riveted plates

A theoretical and experimental analysis of the inspection of reiveted plates using the thermoelastic effect is presented. Theoretically, a model is employed to estimate the thermoelastic response expected from a cracked and uncracked rivet hole. The stress invariant, which causes the thermoelastic response, is calculated for the cracked case using an FEM model and for the uncracked case using a theoretical approximation. The differences in the two thermal responses are reduced when the effects of optical spatial averaging, thermal conduction, and a concentric blind area representing the rivet heat are considered. It is suggested that discrimination between the cracked and uncracked cases for short cracks will improve with increasing frequency of stress oscillation. Measurements are shown for aerospace aluminum samples with and without fatigue cracks propagating from holes in a plate. The effect of mean stress on the thermoelastic response is illustrated, and the results are qualitatively compared with the finite element analysis.

Welch, Christopher S.↗