Search NASA⌕ Search

Engineering topics

Crigler, John L

Publications and source records attributed to Crigler, John L.

16 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1957

Comparison of calculated and experimental load distributions on thin wings at high subsonic and sonic speeds

A method for calculating the aerodynamic loading on a wing in combination with a body is presented. Calculated results are compared with experimentally measured data for two wing-body configurations throughout a range of Mach number up to 1.0. The magnitude and the distribution of spanwise loading of the calculated data are generally in good agreement with the experimental data.

WINGS, COMPLETE - THEORY↗
NASA NTRS1952

Calculation of aerodynamic forces on a propeller in pitch or yaw

An analysis was made to determine the applicability of existing propeller theory and the theory of oscillating airfoils to the problem of determining the magnitude of the forces on propellers in pitch or yaw. Strip calculations using compressible airfoil characteristics were first made as though steady-state conditions existed successively at several blade positions of the propeller blades during one revolution. A theory of oscillating airfoils in pulsating incompressible potential flow was then considered from which it was possible to determine factors which would modify the steady-state forces.

PROPELLERS - PITCH AND YAW↗
NASA NTRS1949

Application of Theodorsen's theory to propeller design

A theoretical analysis is presented for obtaining, by use of Theodorsen's propeller theory, the load distribution along a propeller radius to give the optimum propeller efficiency for any design condition. The efficiencies realized by designing for the optimum load distribution are given in graphs, and the optimum efficiency for any design condition may be read directly from the graph without any laborious calculations. Examples are included to illustrate the method of obtaining the optimum load distributions for both single-rotating and dual-rotating propellers.

Crigler, John L↗
NASA NTRS1948

Application of Theodorsen's Theory to Propeller Design

A theoretical analysis is presented for obtaining by use of Theodorsen's propeller theory the load distribution along a propeller radius to give the optimum propeller efficiency for any design condition.The efficiencies realized by designing for the optimum load distribution are given in graphs, and the optimum efficiency for any design condition may be read directly from the graph without any laborious calculations. Examples are included to illustrate the method of obtaining the optimum load distributions for both single-rotating and dual-rotating propellers.

Crigler, John L↗
NASA NTRS1941

Propeller Analysis from Experimental Data

The operation of the propeller is analyzed by the use of the distribution of forces along the radius, combined with theoretical equations. The data were obtained in the NACA 20-foot wind tunnel on a 4-foot-diameter, two-blade propeller, operating in front of four body shapes, ranging from a small shaft to support the propeller to conventional NACA cowling. A method of estimating the axial and the rotational energy in the wake as a fractional part of the propeller power is given. A knowledge of the total thrust and torque is necessary for the estimation.

Stickle, George W↗
NASA NTRS1941

Pressure Available for Cooling with Cowling Flaps

Report presents the results of a full-scale investigation conducted in the NACA 20-foot tunnel to determine the pressure difference available for cooling with cowling flaps. The flaps were applied to an exit slot of smooth contour at 0 degree flap angle. Flap angles of 0 degree, 15 degrees, and 30 degrees were tested. Two propellers were used; propeller c which has conventional round blade shanks and propeller f which has airfoil sections extending closer to the hub. The pressure available for cooling is shown to be a direct function of the thrust disk-loading coefficient of the propeller.

Stickle, George W↗
NASA NTRS1941

Effect of Body Nose Shape on the Propulsive Efficiency of a Propeller

Report presents the results of an investigation of the propulsive efficiency of three adjustable propellers of 10-foot diameter operated in front of four body nose shapes, varying from streamline nose that continued through the propeller plane in the form of a large spinner to a conventional open-nose radial-engine cowling. One propeller had airfoil sections close to the hub, the second had conventional round blade shanks, and the third differed from the second only in pitch distribution. The blade-angle settings ranged from 20 degrees to 55 degrees at the 0.75 radius. The effect of the body nose shape on propulsive efficiency may be divided into two parts: (1) the change in the body drag due to the propeller slipstream and (2) the change in propeller load distribution due to the change in velocity caused by the body. For the nose shape tested in the report, the first effect is shown to be very small; therefore, the chief emphasis of the report is confined to the second effect.

Stickle, George W↗
NASA NTRS1940

Effect of Exit-Slot Position and Opening on the Available Cooling Pressure for NACA Nose-Slot Cowlings

Report presents the results of an investigation of full-scale nose-slot cowlings conducted in the NACA 20-foot wind tunnel to furnish information on the pressure drop available for cooling. Engine conductances from 0 to 0.12 and exit-slot conductances from 0 to 0.30 were covered. Two basic nose shapes were tested to determine the effect of the radius of curvature of the nose contour; the nose shape with the smaller radius of curvature gave the higher pressure drop across the engine. The best axial location of the slot for low-speed operation was found to be in the region of maximum negative pressure for the basic shape for the particular operating condition. The effect of the pressure operating condition on the available cooling pressure is shown.

Stickle, George W↗