Engineering topics

Crippen, J.

Publications and source records attributed to Crippen, J..

4 records

DOE OSTI2023

Developing a platform for Fresnel diffractive radiography with 1 μ m spatial resolution at the National Ignition Facility

An x-ray Fresnel diffractive radiography platform was designed for use at the National Ignition Facility. It will enable measurements of micron-scale changes in the density gradients across an interface between isochorically heated warm dense matter materials, the evolution of which is driven primarily through thermal conductivity and mutual diffusion. Here we use 4.75 keV Ti K-shell x-ray emission to heat a 1000 μm diameter plastic cylinder, with a central 30 μm diameter channel filled with liquid D 2 , up to 8 eV. This leads to a cylindrical implosion of the liquid D 2 column, compressing it to ~2.3 g/cm 3 . After pressure equilibration, the location of the D 2 /plastic interface remains steady for several nanoseconds, which enables us to track density gradient changes across the material interface with high precision. For radiography, we use Cu He- α x rays at 8.3 keV. Using a slit aperture of only 1 μm width increases the spatial coherence of the source, giving rise to significant diffraction features in the radiography signal, in addition to the refraction enhancement, which further increases its sensitivity to density scale length changes at the D 2 /plastic interface.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2020

Fill tube dynamics in inertial confinement fusion implosions with high density carbon ablators

Plasma jets, such as γ-ray burst jets, Herbig–Haro jets, μ-quasar jets, and active galactic nuclei jets, are found throughout the universe [S. Mendoza et al., Rev. Mex. Astron. Astrofis. 41, 453 (2005)]. Plasma jets are also present in indirect drive inertial confinement fusion experiments originating from the capsule's fill tube and occasionally from divots and voids in the capsules, particles on the exterior of the capsule, or from the tent holding the capsule in the target. This paper looks at two different gas-filled capsule implosions containing a plasma jet resulting from a capsule fill tube and fill channel, both of which utilized high density carbon ablators. Two models were developed, a drag and a snowplow model, which use the time-dependent motion of the injected mass through the hotspot to estimate the mass injected into the hotspot from the fill tube and channel, arriving at an average injected mass of ~84.5 ± 25.5 ng for the first experiment and 91 ± 20 ng for the second experiment. Furthermore, unlike previous methods to estimate fill tube injected mass, these techniques do not assume that the mixed mass is in thermal equilibrium with the hotspot or that the x-ray emission is only coming from within the hotspot itself. This paper also discusses the features seen in these experiments which include limb brightening in the shell for undoped ablators and flattening in the ablator from shadowing by the fill tube.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2020

Recent and planned hydrodynamic instability experiments on indirect-drive implosions on the National Ignition Facility

At National Ignition Facility (NIF), yield amplification due to alpha particle heating approached ~3 in the highest performing inertial confinement fusion (ICF) implosions, while yield amplification of ~15-30 is needed for ignition. Hydrodynamic instabilities are a major factor in degradation of implosions while understanding and mitigation of the instabilities are critical to achieving ignition. This article describes recent and planned hydrodynamic instability experiments with several focused platforms that have been developed to directly measure these instabilities in all phases of ICF implosions. Measurements of ripple-shock generation at OMEGA laser have indicated initial seeds for the instabilities in three ablators - plastic (CH), beryllium, and high-density carbon (HDC). Hydrodynamic Growth Radiography (HGR) platform was used to measure instability growth at the ablation front in the acceleration phase of implosions. This platform used pre-imposed 2-D perturbations for growth factor measurements at different perturbation wavelengths and was also used to measure growth of “native roughness” modulations, fill tubes, and capsule support membranes or “tents”. Also, in the acceleration phase several new experimental platforms have been or are being developed to measure instability growth at the ablator-ice interface. In the deceleration phase of implosions, “self-emission” and “self-backlighting” platforms were developed to measure perturbations near peak compression. This article reviews recent progress and results.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2020

Mixing in ICF implosions on the National Ignition Facility caused by the fill-tube

The micrometer-scale tube that fills capsules with thermonuclear fuel in inertial confinement fusion experiments at the National Ignition Facility is also one of the implosion's main degradation sources. It seeds a perturbation that injects the ablator material into the center, radiating away some of the hot-spot energy. This paper discusses how the perturbation arises in experiments using high-density carbon ablators and how the ablator mix interacts once it enters the hot-spot. Both modeling and experiments show an in-flight areal-density perturbation and localized x-ray emission at stagnation from the fill-tube. Simulations suggest that the fill-tube is degrading an otherwise 1D implosion by ~2×, but when other degradation sources are present, the yield reduction is closer to 20%. Characteristics of the fill-tube assembly, such as the through-hole size and the glue mass, alter the dynamics and magnitude of the degradation. Overall, these aspects point the way toward improvements in the design, some of which (smaller diameter fill-tube) have already shown improvements.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗