Search NASA⌕ Search

Engineering topics

Crocker, M. J.

Publications and source records attributed to Crocker, M. J..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Analytical and experimental study of the vibration of bonded beams with a lap joint

A theoretical model to study the flexural vibration of a bonded lap joint system is described in this paper. First, equations of motion at the joint region are derived using a differential element approach. The transverse displacements of the upper and lower beam are considered to be different. The adhesive is assumed to be linearly viscoelastic and the widely used Kelvin-Voight model is used to represent the viscoelastic behavior of the adhesive. The shear force at the interface between the adhesive and the beam is obtained from the simple bending motion equations of the two beams. The resulting equations of motion are combined with the equations of transverse vibration of the beams in the unjointed regions. These are later solved as a boundary value problem to obtain the eigenvalues and eigenvectors of the system. The model can be used to predict the natural frequencies, modal damping ratios, and mode shapes of the system for free vibration. Good agreement between numerical and experimental results was obtained for a system of graphite epoxy beams lap-jointed by an epoxy adhesive.

Rao, M. D.↗
NASA NTRS1990

Mechanical system diagnostics using vibration testing techniques

The 'Cepstrum' technique of vibration-path identification allows the recovery of the transfer function of a system with little knowledge as to its excitation force, by means of a mathematical manipulation of the system output in conjunction with subtraction of part of the output and suitable signal processing. An experimental program has been conducted to evaluate the usefulness of this technique in the cases of simple, cantilever-beam and free-free plate structures as well as in that of a complex mechanical system. On the basis of the transfer functions thus recovered, it was possible to evaluate the shifts in the resonance frequencies of a structure due to the presence of defects.

Mcleod, Catherine D.↗
NASA NTRS1987

Experimental study of damping of graphite epoxy composite material of the Space Telescope truss system

The truss system of the Hubble Space Telescope is made of graphite epoxy tubes and beams that have very low material damping. This paper describes a systematic experimental evaluation of the damping capacity of the graphite epoxy material used in the telescope truss system. The damping capacity of the composite material was measured both under normal and elevated temperatures in atmospheric conditions and in vacuum. Both free decay and steady state methods were used to measure the damping ratio of different specimens under different boundary conditions. A method that involves an iterative least-squares curve-fitting technique for the measured frequency response data has been developed to improve the accuracy of the damping ratio estimation. A unique experimental setup was developed to measure the damping of the material in a vacuum chamber. It was found that outgassing (moisture desorption) has little effect on the damping of the specimen. On the other hand, it was observed that temperature has a significant effect on both the damping and resonance frequencies of the specimen.

Rao, M. D.↗
NASA NTRS1985

Measurement of damping of graphite epoxy materials

Work on a damping measurement test apparatus is discussed. The device is designed to excite tube specimens in a vacuum chamber. Also some experiments were conducted on a tube specimen to confirm previously reported results. A table of data showing the results of forced vibration tests using a half ring and a free-free boundary is given. The main purpose was to study the effect of the frequency resolution on the damping ratio measurements.

Crocker, M. J.↗
NASA NTRS1985

Measurement of damping of graphite expoxy materials

During this period damping measurements were made on the cylindrical graphite epoxy specimen using the forced-vibration test method. The specimen was carefully mounted directly on the shaker through the supporting ring and the impedance head. This was done to simulate an idealized free-free boundary condition at the two edges. The damping ratio value and the natural frequency (first mode) obtained in this experiment were 0.13% and 508.75 Hz respectively. In order to check the damping induced by the supporting ring, measurements were made with the top half of the ring removed. The specimen then was supported only by the bottom half of the ring (half ring). It was observed that the natural frequency of the specimen (first mode) increased of a value of 552.5 Hz due to the influence of the reduced mass of the supporting ring. But the damping ratio value obtained was the same as that obtained with full supporting ring, namely 0.13%.

Crocker, M. J.↗
NASA NTRS1985

Measurement of damping of graphite epoxy materials

The design of an experiment to measure the damping of a cylindrical graphite-epoxy specimen with a three point support and a knife edge support is described as well as equipment used in tests conducted to determine the influence of the support at the two ends of the specimen and to simulate an idealized free-free boundary condition at the two edges. A curve fitting technique is being used to process the frequency response data obtained. Experiments conducted on the thin plate specimen also reveal the influence of the end support condition on the damping ratio of the specimen. The damping ratio values measured for both specimens appear to be strongly influenced by the shape of the specimen and appear to depend on length and fiber orientation as well as the presence of discontinuities such as sharp bends, corners, and notches.

Crocker, M. J.↗
NASA NTRS1985

The effect on the transmission loss of a double wall panel of using helium gas in the gap

The possibility of increasing the sound-power transmission loss of a double panel by using helium gas in the gap is investigated. The transmission loss of a panel is defined as ten times the common logarithm of the ratio of the sound power incident on the panel to the sound power transmitted to the space on the other side of the panel. The work is associated with extensive research being done to develop new techniques for predicting the interior noise levels on board high-speed advanced turboprop aircraft and reducing the noise levels with a minimum weight penalty. Helium gas was chosen for its inert properties and its low impedance compared with air. With helium in the gap, the impedance mismatch experienced by the sound wave will be greater than that with air in the gap. It is seen that helium gas in the gap increases the transmission loss of the double panel over a wide range of frequencies.

Atwal, M. S.↗
NASA NTRS1985

Experimental evaluation of damping of graphite fiber composites

An investigation is described that was conducted to measure the damping of graphite fiber composites such as are to be used on the Hubble Space Telescope. The measurements were made on a composite cylinder under normal atmospheric conditions and in a vacuum chamber with varying thermal conditions. Such composites can outgas under vacuum conditions and this emission of trapped gases may have some influence on the material damping. Some results are presented for the damping coefficient measured under normal atmospheric conditions for a graphite fiber composite. The experimental damping data thus obtained were compared with the least square estimate obtained through a statistical analysis. The statistical analysis was based on a linear mathematical model consisting of a spring in parallel with a dashpot. It is observed that the discrepancy in the damping ratio between logarithmic decrement result and the least square fit is less than 6 percent for all the different tests made on the composite cylinder. Signal-to-noise ratio was maintained to be greater than 10.

Rao, M. D.↗
NASA NTRS1985

Investigation of the level difference between sound pressure and sound intensity in an aircraft cabin under different fuselage conditions

Problems in using two-microphone sound-intensity (SI) measurements to measure structural transmission losses are investigated in experiments involving light-aircraft fuselage panels and windows. Both sound pressure (SP) and SI are measured near the passenger and door windows and panels of a single-engine aircraft and with these barriers removed, and the effect of increasing interior acoustic absorption and blocking flanking transmission paths is also tested. The results are presented graphically, and the SP measurements are used to indicate frequency ranges in which the two-microphone technique significantly underestimates SI. It is inferred that flanking paths and interior reverberation must be effectively suppressed in order to obtain accurate transmission-loss measurements.

Atwal, M. S.↗
NASA NTRS1983

Light aircraft sound transmission study

The revived interest in the design of propeller driven aircraft is based on increasing fuel prices as well as on the need for bigger short haul and commuter aircraft. A major problem encountered with propeller driven aircraft is propeller and exhaust noise that is transmitted through the fuselage sidewall structure. Part of the work which was conducted during the period April 1 to August 31, 1983, on the studies of sound transmission through light aircraft walls is presented.

Atwal, M.↗
NASA NTRS1982

Direct measurement of transmission loss of aircraft structures using the acoustic intensity approach

A measurement technique is developed in order to obtain the sound transmission loss of an aircraft fuselage which obviates the need for the two-room transmission suite. The sound transmission paths were determined in tests on a light aircraft fuselage using a two-microphone acoustic intensity method for measuring the acoustic intensity transmitted to the interior when the fuselage was exposed to an external random incidence sound-field. The intensity transmitted through different sections of the fuselage can be estimated accurately using this new technique. Results of these tests show that the plexiglass window is the major transmission path in the high frequency range. In addition, the transmission losses through a single and a double layer window were predicted theoretically by using the Statistical Energy Analysis Model. Very good agreement is found between the predictions and the measurements.

Wang, Y. S.↗
NASA NTRS1982

Phase shift errors in the theory and practice of surface intensity measurements

The surface acoustical intensity method (sometimes known as the microphone-accelerometer cross-spectral method) is a relatively new noise source/path identification tool. Several researchers have had difficulties implementing this method because of instrumentation phase mis-match. A simple technique for measuring and correcting instrumentation phase mis-match has been developed. This new technique has been tested recently on a noise source identification problem of practical interest. The results of the experiments indicate that the surface acoustic intensity method produces reliable data and can be applied to a variety of noise source/path problems.

Mcgary, M. C.↗
NASA NTRS1981

A study of methods of prediction and measurement of the transmission sound through the walls of light aircraft

Several aspects were studied. The SEA theory was used to develop a theoretical model to predict the transmission loss through an aircraft window. This work mainly consisted of the writing of two computer programs. One program predicts the sound transmission through a plexiglass window (the case of a single partition). The other program applies to the case of a plexiglass window window with a window shade added (the case of a double partition with an air gap). The sound transmission through a structure was measured in experimental studies using several different methods in order that the accuracy and complexity of all the methods could be compared. Also, the measurements were conducted on the simple model of a fuselage (a cylindrical shell), on a real aircraft fuselage, and on stiffened panels.

Forssen, B.↗
NASA NTRS1981

Theoretical and experimental evaluation of transmission loss of cylinders

A technique is reported which evaluates the transmission loss of a cylinder from measurements of the incident and transmitted intensities. Incident intensity is calculated from the space-averaged measured pressure and the assumption that the source space is reverberant. Transmitted intensity is measured by means of the microphone acoustic intensity technique using a fast Fourier transform analyzer. The first dip at the ring frequency, and the other at the critical coincidence frequency are predicted in the transmission loss curve of a cylindrical shell with a 0.762 m diameter and a 1.67 m length. Results are compared and demonstrate good agreement for frequencies above 500 Hz. It is concluded that the technique combining the measurement of both intensities gives accurate results and is simpler and less expensive than the conventional method.

Wang, Y. S.↗
NASA NTRS1980

Surface acoustical intensity measurements on a diesel engine

The use of surface intensity measurements as an alternative to the conventional selective wrapping technique of noise source identification and ranking on diesel engines was investigated. A six cylinder, in line turbocharged, 350 horsepower diesel engine was used. Sound power was measured under anechoic conditions for eight separate parts of the engine at steady state operating conditions using the conventional technique. Sound power measurements were repeated on five separate parts of the engine using the surface intensity at the same steady state operating conditions. The results were compared by plotting sound power level against frequency and noise source rankings for the two methods.

Mcgary, M. C.↗