Experimental aerodynamic characteristics of an NACA 0012 airfoil with simulated ice
Explore the source record for details and available documents.
Korkan, K. D.↗
Engineering topics
Cross, E. J., Jr.
Publications and source records attributed to Cross, E. J., Jr..
Performance degradation of a model helicopter rotor with a generic ice shape
An experimental program using a commercially available remotely controlled model helicopter in the Texas A&M University (TAMU) subsonic wind tunnel has been conducted to investigate the performance degradation resulting from the simulated formation of ice on the leading edge of the main rotor blades in both hover and forward flight. The rotor blades utilized a NACA 0012 airfoil with a 2.5-in. constant chord. A generic ice shape derived from a predetermined natural ice condition was applied to the 53.375-in.-diameter main rotor, and thrust and torque coefficients were measured for the main rotor as functions of velocity, main rotor rpm, fuselage angle of incidence, collective pitch angle, and spanwise extent of icing. The model helicopter test exhibited significant performance degradation of the main rotor when generic ice was added. An increase of approximately 150 percent in torque coefficient to maintain a constant thrust coefficient was noted when generic ice had been applied to the 85 percent rotor radial location. Also, considerable additional degradation occurred when generic ice was applied to the 100 percent rotor radial location, as compared with the 85 percent simulated ice performance values, indicating the sensitivity of the rotor tip region.
Korkan, K. D.↗
Experimental study of performance degradation of a model helicopter main rotor with simulated ice shapes
An experimental study utilizing a remote controlled model helicopter has been conducted to measure the performance degradation due to simulated ice accretion on the leading edge of the main rotor for hover and forward flight. The 53.375 inch diameter main rotor incorporates a NACA 0012 airfoil with a generic ice shape corresponding to a specified natural ice condition. Thrust coefficients and torque coefficients about the main rotor were measured as a function of velocity, main rotor RPM, angle-of-incidence of the fuselage, collective pitch angle, and extent of spanwise ice accretion. An experimental airfoil data bank has been determined using a two-dimensional twenty-one inch NACA 0012 airfoil with scaled ice accretion shapes identical to that used on the model helicopter main rotor. The corresponding experimental data are discussed with emphasis on Reynolds number effects and ice accretion scale model testing.
Korkan, K. D.↗
Performance degradation of a model helicopter main rotor in hover and forward flight with a generic ice shape
A model helicopter has been used to collect test data and provide an experimental means of studying helicopter performance in a subsonic wind tunnel. A simulated generic ice shape was attached to the rotor blades and performance data were obtained for both hover and forward flights. Significant degradation in helicopter performance with respect to torque and thrust coefficient was observed; the rotor tip region was especially sensitive. Two-dimensional wind tunnel tests were conducted over a Reynolds number range 0.7-3 x 10 to the 6th in order to investigate the effect of Reynolds number on the aerodynamic performance of the airfoil in both clean and iced configurations. Only minimal dependence of the aerodynamic data on Reynolds number was observed.
Korkan, K. D.↗
Flight test method for the determination of reciprocating engine cooling requirements
It is pointed out that the effective cooling of aircraft reciprocating engines is still a problem area for the general aviation industry. Miley et al. (1981) have reported the results of an investigation of problems associated with cooling and installation aerodynamics. A description is given of a flight test procedure which was developed in connection with the considered investigation. It is shown that the test procedure provides valid cooling requirements data for a particular installation. The data are in terms of easily measurable parameters. The employment of the test procedure, which is based on the NACA cooling correlation method, can lead to more effective cooling installations and the solution of existing cooling problems.
Miley, S. J.↗
An experimental investigation of the aerodynamics and cooling of a horizontally-opposed air-cooled aircraft engine installation
A flight-test based research program was performed to investigate the aerodynamics and cooling of a horizontally-opposed engine installation. Specific areas investigated were the internal aerodynamics and cooling mechanics of the installation, inlet aerodynamics, and exit aerodynamics. The applicable theory and current state of the art are discussed for each area. Flight-test and ground-test techniques for the development of the cooling installation and the solution of cooling problems are presented. The results show that much of the internal aerodynamics and cooling technology developed for radial engines are applicable to horizontally opposed engines. Correlation is established between engine manufacturer's cooling design data and flight measurements of the particular installation. Also, a flight-test method for the development of cooling requirements in terms of easily measurable parameters is presented. The impact of inlet and exit design on cooling and cooling drag is shown to be of major significance.
Miley, S. J.↗
Full scale visualization of the wing tip vortices generated by a typical agricultural aircraft
The trajectories of the wing tip vortices of a typical agricultural aircraft were experimentally determined by flight test. A flow visualization method, similar to the vapor screen method used in wind tunnels, was used to obtain trajectory data for a range of flight speeds, airplane configurations, and wing loadings. Detailed measurements of the spanwise surface pressure distribution were made for all test points. Further, a powered 1/8 scale model of the aircraft was designed, built, and used to obtain tip vortex trajectory data under conditions similar to that of the full-scale test. The effects of light wind on the vortices were demonstrated, and the interaction of the flap vortex and the tip vortex was clearly shown in photographs and plotted trajectory data.
Cross, E. J., Jr.↗
Full scale visualization of the wing tip vortices generated by a typical agricultural aircraft
The trajectories of the wing tip vortices of a typical agricultural aircraft were experimentally determined by flight test. A flow visualization method, similar to the vapor screen method used in wind tunnels, was used to obtain trajectory data for a range of flight speeds, airplane configurations, and wing loadings. Detailed measurements of the spanwise surface pressure distribution were made for all test points. Further, a powered 1/8 scale model of the aircraft was designed, built, and used to obtain tip vortex trajectory data under conditions similar to that of the full scale test. The effects of light wind on the vortices were demonstrated, and the interaction of the flap vortex and the tip vortex was clearly shown in photographs and plotted trajectory data.
Cross, E. J., Jr.↗
Determination of cooling air mass flow for a horizontally-opposed aircraft engine installation
The relationship between the amount of cooling air flow and the corresponding flow pressure difference across an aircraft engine was investigated in flight and on the ground. The flight test results were consistent with theory, but indicated a significant installation leakage problem. A ground test blower system was used to identify and reduce the leakage. The correlation between ground test cell determined engine orifice characteristics and flight measurements showed good agreement if the engine pressure difference was based on total pressure rather than static pressure.
Miley, S. J.↗
Aerodynamics of horizontally-opposed aircraft engine installations
The goal of cooling installation design is to provide adequate cooling air flow to the engine with a minimum drag penalty. To achieve this goal, attention must be given to certain aerodynamic factors involved in the design problem. In the present paper, the factors which influence the aerodynamic design of horizontally-opposed engine cooling installations are discussed with particular reference to the performance of the aircraft in terms of the dynamic pressure generated for the power output of the engine, the gains or losses through the propeller, proper inlet design, altitude effects on the orifice characteristics of the engine, and exit area sizing. Results of a flight research program showed that the inlet design has a significant influence on cooling effectiveness and drag; the inlet should be designed for low velocity ratios and should avoid small radii of curvature in its geometry. The influence of the propeller on the inlet appears to cause the stagnation point on the lip to move toward the inside.
Miley, S. J.↗
Flight test evaluation of a method to determine the level flight performance of a propeller-driven aircraft
A flight test method has been developed for determining the level flight drag and propulsive efficiency of propeller-driven aircraft. The overall drag of the aircraft is expressed in terms of the measured increment of power required to overcome a corresponding known increment of drag, which is generated by a towed drogue. The simplest form of the governing equations, D = delta D SHP/delta SHP (where D is drag and SHP is the horsepower delivered to the propeller) is such that all of the parameters on the right side of the equation can be measured in flight. An evaluation of the governing equations has been performed using data generated by flight test of a Beechcraft T-34B.
Bridges, P. D.↗
Flight test evaluation of a method to determine the level flight performance of a propeller-driven aircraft
The overall drag of the aircraft is expressed in terms of the measured increment of power required to overcome a corresponding known increment of drag, which is generated by a towed drogue. The simplest form of the governing equations, D = delta D SHP/delta SHP, is such that all of the parameters on the right side of the equation can be measured in flight. An evaluation of the governing equations has been performed using data generated by flight test of a Beechcraft T-34B. The simplicity of this technique and its proven applicability to sailplanes and small aircraft is well known. However, the method fails to account for airframe-propulsion system.
Bridges, P. G.↗
Flight test evaluation of a method to determine the level flight performance propeller-driven aircraft
A procedure is developed for deriving the level flight drag and propulsive efficiency of propeller-driven aircraft. This is a method in which the overall drag of the aircraft is expressed in terms of the measured increment of power required to overcome a corresponding known increment of drag. The aircraft is flown in unaccelerated, straight and level flight, and thus includes the effects of the propeller drag and slipstream. Propeller efficiency and airplane drag are computed on the basis of data obtained during flight test and do not rely on the analytical calculations of inadequate theory.
Cross, E. J., Jr.↗