Engineering topics

Crowder, J. P.

Publications and source records attributed to Crowder, J. P..

7 records

NASA NTRS1982

Surface flow visualization using indicators

Surface flow visualization using indicators in the cryogenic wind tunnel which requires a fresh look at materials and procedures to accommodate the new test conditions is described. Potential liquid and gaseous indicators are identified. The particular materials illustrate the various requirements an indicator must fulfill. The indicator must respond properly to the flow phenomenon of interest and must be observable. Boundary layer transition is the most important phenomenon for which flow visualization indicators may be employed. The visibility of a particular indicator depends on utilizing various optical or chemical reactions. Gaseous indicators are more difficult to utilize, but because of their diversity may present unusual and useful opportunities. Factors to be considered in selecting an indicator include handling safety, toxicity, potential for contamination of the tunnel, and cost.

Crowder, J. P.↗

NASA NTRS1982

In-flight propeller flow visualization using fluorescent minitufts

Extension of fluorescent minutuft method to in-flight flow visualization on propellers is described. Extremely thin nylon monofilament for the minitufts, is used in a process of attaching them to the test surface with small drops of lacquer-like adhesive, and the use of fluorescence photography for recording the minituft patterns. Using this method, thousands of minitufts can be applied to small, high speed wind tunnel models without affecting the airflow. The minitufts can remain in place throughout a wind tunnel test, permitting nonintrusive flow visualization data to be acquired at any time.

Crowder, J. P.↗

NASA NTRS1982

Transonic applications of the Wake Imaging System

The extension of a rapid flow field survey method (wake imaging system) originally developed for low speed wind tunnel operation, to transonic wind tunnel applications is discussed. The advantage of the system, beside the simplicity and low cost of the data acquisition system, is that the probe position data are recorded as an optical image of the actual sensor and thus are unaffected by the inevitable deflections of the probe support. This permits traversing systems which are deliberately flexible and have unusual motions. Two transverse drive systems are described and several typical data images are given.

Crowder, J. P.↗

NASA NTRS1978

Propeller slipstream wing interactions at Mach no. 0.8

Configuration and results of a wind tunnel test of the aerodynamic interactions between propeller slipstream and a supercritical wing at transonic Mach numbers are discussed. The test was conducted over a free-stream Mach number range from 0.7 to 0.84, with the slipstream simulator and the wing-body model installed in the tunnel. The angle of attack and the spanning lift coefficients were varied from 1 to 3 deg and from 0.4 to 0.7 deg respectively, while the slipstream swirl angle was varied from 0 to 11 deg with an upwash on the inboard side of the wing. It was found that at a free-stream Mach number of 0.8 and a lift coefficient of 0.5, incremental drag results for 7 deg of swirl and a slipstream Mach number of 0.87 indicated a penalty equivalent to a 0.024 loss in propeller efficiency, whereas at 11 deg the drag increment was favorable. Swirl had significant effects on the chordwise pressure distributions of the inboard section of the wing within the slipstream. Neither surface nor wake pressures showed signs of significant flow separation induced by the slipstream.

Bencze, D. P.↗

NASA NTRS1978

Simulated propeller slipstream effects on a supercritical wing

To quantify the installed performance of high speed (M = 0.8) turboprop propulsion systems, an experimental program designed to assess the magnitude of the aerodynamic interference of a propeller slipstream on a supercritical wing has been conducted. The test was conducted in the NASA Ames 14-foot wind tunnel. An ejector-nacelle propeller slipstream simulator was used to produce a slipstream with characteristics typical of advanced propellers presently being investigated. A supercritical wing-body configuration was used to evaluate the interference effects. A traversing total pressure rake was used to make flow field measurements behind the wing and to calibrate the slipstream simulator. The force results indicated that the interference drag amounted to an increase of ten counts or about 3% of the wing-body drag for a two engine configuration at the nominal propeller operating conditions. However, at the higher swirl angles (11 deg vs. 7 deg nominally) the interference drag was favorable by about the same magnitude.

Welge, H. R.↗

NASA NTRS1975

STOL aircraft transient ground effects. Part 1: Fundamental analytical study

The first phases of a fundamental analytical study of STOL ground effects were presented. Ground effects were studied in two dimensions to establish the importance of nonlinear effects, to examine transient aspects of ascent and descent near the ground, and to study the modelling of the jet impingement on the ground. Powered lift system effects were treated using the jet-flap analogy. The status of a three-dimensional jet-wing ground effect method was presented. It was shown, for two-dimensional unblown airfoils, that the transient effects are small and are primarily due to airfoil/freestream/ground orientation rather than to unsteady effects. The three-dimensional study showed phenomena similar to the two-dimensional results. For unblown wings, the wing/freestream/ground orientation effects were shown to be of the same order of magnitude as for unblown airfoils. This may be used to study the nonplanar, nonlinear, jet-wing ground effect.

Goldhammer, M. I.↗

NASA NTRS1975

STOL aircraft transient ground effects. Part 2: Experimental techniques feasibility study

Procedures for simulating transient effects associated with STOL aircraft landings and takeoffs were examined and a basis was developed for selection of an experimental approach based on consideration of simulation requirements, experimental techniques, facilities, and costs. The results are generally applicable to STOL aircraft employing any of the following powered lift systems: externally blown flap, upper surface blown flap, augmentor wing, or internally ducted jet flap. Scaling relationships were developed to apply the simulation requirements to model test situations. Procedures for the derivation of aerodynamic forces from the measured data were discussed. Various means of expressing the aerodynamic data in forms convenient for use in performance or stability and control applications were described. Five different experimental techniques were presented that depend on two different types of experimental facilities, wind tunnels and test tracks, and involving different types of model motion, and factors pertinent to selection were summarized.

Crowder, J. P.↗