Search NASA⌕ Search

Engineering topics

Croy, Jason

Publications and source records attributed to Croy, Jason.

Designing Particle Morphologies for Materials with Solid Transport Limitations: A Case Study of Lithium and Manganese Rich Cathode Oxides

A lithium and manganese rich nickel-manganese-cobalt oxide (LMR-NMC) cathode is a promising candidate for next-generation batteries due to its high specific capacity, low cost, and low cobalt content. However, the material suffers from poor rate capability due to the diffusion limitations of lithium in the cathode particles. Understanding the material performance requires careful control of the morphology of the cathode particles, taking into account the primary and agglomerated diffusion pathways and the presence of pores, some of which could be closed from electrolyte infiltration. Here, in this study, we use a microstructure-based mathematical model combined with experimental data to understand the role of the complex cathode particle morphology in the rate performance of the material. Scanning electron microscopy images of cathodes made under different synthesis conditions, which results in different agglomerate morphologies, serve as the input into the mathematical model. The model is then compared to rate data to understand the controlling parameters. The presence of intra-agglomerate closed pores results in a large agglomerate diffusion length in comparison to the ideal condition, where the primary particles are agglomerated in an open and dispersed manner such that the entire interfacial area is available for electrochemical reaction. Smaller primary and agglomerate diffusion lengths result in better electrochemical performance. This points us toward designing the morphology of the cathode particles to compensate for the diffusion limitation of LMR-NMC while maximizing the density.

Tewari, Deepti↗

Lithium battery electrodes

Electrode materials for electrochemical cells and batteries and methods of producing such materials are disclosed herein. The electrode materials comprise an active lithium metal oxide material prepared by: (a) contacting the lithium metal oxide material with an aqueous acidic solution containing one or more metal cations; and (b) heating the so-contacted lithium metal oxide from step (a) to dryness at a temperature below 200° C. The metal cations in the aqueous acidic solution comprise one or more metal cations selected from the group consisting of an alkaline earth metal ion, a transition metal ion, and a main group metal ion.

25 ENERGY STORAGE↗

Concealed Cathode Degradation in Lithium-Ion Cells with a Ni-Rich Oxide

Difficulties with sourcing cobalt and the interest in increasing cell energy have motivated the development of Ni-rich oxide materials for lithium-ion battery cathodes. Despite the intense research on the topic, there is limited information available on the long-term performance of novel cathode formulations. Here, we evaluate the stability of LiNi 0.9 Mn 0.05 Co 0.05 O 2 in full-cells tested for over five months, assessing how cycling, voltage and electrolyte additives impact cathode aging. We use differential voltage analysis to extract insights about the cathode from the full-cell data and identify the isolation of cathode particles in the delithiated (charged) state as a relevant mode of aging. Importantly, this particular mechanism of cathode aging does not cause immediate cell capacity fade, causing the simple analysis of cell capacity retention to overestimate the cathode stability under the investigated conditions. So, our observations serve as cautionary tale indicating that careful analysis of data from extended testing may be required for assessing the performance of Ni-rich cathodes and for evaluating how these materials are affected by electrolyte additives.

25 ENERGY STORAGE↗

Critical Barriers to Successful Implementation of Earth-Abundant, Mn-Rich Cathodes for Vehicle Applications and Beyond: The Effect of Particle Morphology

As the search for improved and next-generation cathodes continues, it is clear that a deeper understanding of synthesis–structure–electrochemical property relationships is of critical importance. The effects of primary and secondary particle morphologies on various transition metal oxides have been studied, but new findings are still being reported. To date, few studies have focused on the effects of particle morphologies on Li- and Mn-rich oxides (>50% Mn) and even fewer studies have focused on the influence over key properties such as electrode-level impedance. In this study, we report the effects of particle morphologies on the area-specific-impedance (ASI) and thermal behavior of Li- and Mn-rich oxides. Samples with a fixed, layered–layered–spinel (LLS), composition were synthesized with differing primary morphologies and tested under standardized, full-cell protocols. The results suggest that smaller primary particle size (i.e., higher surface area) leads to lower overall ASI, a delay in the increasing impedance at low states-of-charge (SOCs), and surprisingly, improved thermal behavior.

33 ADVANCED PROPULSION SYSTEMS↗

Multifunctional Films Deposited by Atomic Layer Deposition for Tailored Interfaces of Electrochemical Systems

A new strategy for electrochemical interfaces that utilizes multilayer films deposited by atomic layer deposition (ALD) is introduced. Manganese-rich and nickel-rich cathode oxides were coated with a novel bilayer film of metal fluorides. Subsequent exposure to prolonged, high-voltage electrochemical cycling vs graphite electrodes revealed that the bilayer film can greatly enhance the high-voltage stability of cathode oxides. In particular, in manganese-rich cells, capacity fade due to manganese dissolution was substantially reduced and impedance rise was virtually eliminated. Furthermore, in nickel-rich NMC-811 cells, impedance rise was reduced by ~80%, compared to the NMC-811 baseline, after ~300 h of high-voltage exposure during cycling. Here, the multilayer film strategy presents an exciting opportunity for tailoring designs and materials for electrochemical interfaces in advanced lithium-ion batteries and beyond.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

High valent lithiated surface structures for lithium ion battery electrode materials

The surface of a lithium ion cathode material (e.g., a lithium metal oxide material capable of releasing and accepting lithium ions during charging and discharging, respectively, of a lithium ion electrochemical cell) is coated with a lithium metal oxide (LMO) material comprising a high-valent metal to, inter alia, reduce interfacial resistance toward lithium exchange. Li-rich phases on the surface of the treated LMO particles allow for better lithium ion diffusion. The inclusion of elements that form phases with lithium and can substitute in the host structure allow for mixing across interfaces leading to more robust structures that better mimic epitaxial-type layers. Inclusion of doping elements in place of some of the high-valent metal in the surface-treating composition provides unexpectedly improved performance over surface treatments comprising lithium metal oxides that only include a high-valent metal.

36 MATERIALS SCIENCE↗

Stabilized electrodes for lithium batteries

A structurally inhomogeneous lithium metal oxide material having the Formula (I): y[xLi2MO3•(1-x)LiM′O2]•(1-y)Li1+dM″2−dO4; wherein 0≤x≤1; 0<y<1; 0≤d≤0.33; and wherein the Li1+dM″2−dO4 component comprises a spinel structure, and each of the Li2MO3 and the LiM′2 components thereof comprise layered structures. Each of M, M′, and M″ independently comprises one or more metal ions. The composition of the material of Formula (I) varies across the electrode particles by changing at least one of x, y, d, M, M′ and M″. Electrodes, cells and batteries comprising the lithium metal oxide material are also described.

Thackeray, Michael M.↗

Electrode structures and surfaces for Li batteries

This invention relates to methods of preparing positive electrode materials for electrochemical cells and batteries. It relates, in particular, to a method for fabricating lithium-metal-oxide electrode materials for lithium cells and batteries. The method comprises contacting a hydrogen-lithium-manganese-oxide material with one or more metal ions, preferably in an acidic solution, to insert the one or more metal ions into the hydrogen-lithium-manganese-oxide material; heat-treating the resulting product to form a powdered metal oxide composition; and forming an electrode from the powdered metal oxide composition.

25 ENERGY STORAGE↗