Engineering topics

Cruz, C. I.

Publications and source records attributed to Cruz, C. I..

5 records

NASA NTRS1993

Hypersonic aerodynamic characteristics for Langley Test Technique Demonstrator

Experimental longitudinal and lateral-directional aerodynamic characteristics were obtained for a generic transatmospheric vehicle concept referred to as the Langley Test Technique Demonstrator. The baseline configuration, without engine modules, was longitudinally and directionally unstable over the hypersonic Mach number range of the investigation and exhibited untrimmed (L/D)max levels between 2.6 and 2.8. Adding various engine modules to the baseline configuration produced mainly, degradations in lift-to-drag ratio. In general, longitudinal aerodynamic coefficients predicted with an engineering code referred to as Aerodynamic Preliminary Analysis System (APAS) were in qualitative, and often quantitative agreement with measurement.

Phillips, W. P.↗

NASA NTRS1986

Analysis of separation of a two-stage winged launch vehicle

The feasibility of separating a two-stage winged, parallel configured launch vehicle at Mach 3 has been determined. The two-stage fully-reusable launch vehicle is comprised of an orbiter, which can be used alone as a single-stage-to-orbit vehicle, and a booster which is identical to the baseline orbiter design. A three-degree-of-freedom analysis was conducted on the ascent trajectory of the two-stage concept to determine the optimum staging conditions. The booster provides all propellant for both stages using a crossfeed system until staging occurs. After staging, the empty booster glides back to the launch site for a horizontal landing. To analyze the separation maneuver, the six-degree-of-freedom equations of motion for both stages were numerically integrated using a computer program which incorporates analytically derived interference aerodynamic data. The necessary conditions for a successful separation were determined and required the use of active controls on both the orbiter and booster. Once the booster and orbiter were separated, a three-degree-of-freedom analysis was conducted on the booster's glideback trajectory.

Naftel, J. C.↗

NASA NTRS1985

Design study of a slant-nose-cylinder aeroassisted orbital transfer vehicle

A slant-nose-cylinder aeroassisted orbital transfer vehicle configuration is described and analyzed in this study. The vehicle is sized for a 12,000 lb roundtrip payload between low earth orbit and geosynchronous orbit and is assumed to be space based. The vehicle can be fabricated using near-term technologies and is fully reusable. Optional advanced technologies offer potential for improved performance. The vehicle can be assembled on the ground and carried to orbit in the Shuttle cargo bay. An enclosed payload bay is provided in the vehicle to protect payloads during the pass through the atmosphere. The payload bay capacity can be increased from a 10 ft to a 14 ft diameter payload by replacing a modular section of the payload bay in space. The results of calculations used to size the vehicle and to predict its performance and weight are presented.

Blosser, M. L.↗

NASA NTRS1985

Orbit on demand - Structural analysis finds vertical launchers weigh less

Structural considerations arising from favored design concepts for the next generation on-demand launch vehicles are explored. The two emerging concepts are a two stage fully reusable vertical take-off vehicle (V-2) and a horizontal take-off, two stage subsonic boost launch vehicle (H-2-Sub). Both designs have an 1100 n. mi. cross-range capability, with the V-2 orbiter having small wings with winglets for hypersonic trim and the H-2-Sub requiring larger, swept wings. The rockets would be cryogenic, while airbreathing initial boosters would be either turbofans, turbojets and/or ramjets. Dynamic loading is lower in the launch of a V-2. The TPS is a critical factor due to thinner leading edges than on the Shuttle and may require heat-pipe cooling. Airframe structures made of metal matrix composites have passed finite element simulations of projected loads and can now undergo proof-of-concept tests, although whisker-reinforced materials may be superior once long-whisker technology is developed.

Taylor, A. H.↗

NASA NTRS1985

Hypersonic characteristics of an advanced aerospace plane

A series of hypersonic wind-tunnel tests have been conducted in the NASA Langley Hypersonic Facilities Complex to obtain the static longitudinal and lateral-directional aerodynamic characteristics of an advanced aerospace plane. Data were obtained at 0 to 20 deg angles of attack and -3 to 3 deg angles of sideslip at Mach numbers of 6 and 10 in air and 20 in helium. Results show that stable trim capability exists at angles of attack near maximum lift-drag ratio (L/D). Both performance and stability exhibited some Mach number dependency. The vehicle was longitudinally unstable at low angles of attack but stable at angles of attack near and above maximum L/D. It was directionally unstable with positive dihedral effect. The rudder showed an inability to provide lateral-directional control, and removing the vertical tail resulted in increased directional instability. Analytical predictions of the static longitudinal aerodynamic coefficients gave relatively good comparisons with the experimental data.

Mccandless, R. S.↗