Search NASA⌕ Search

Engineering topics

Cuevas, Andres

Publications and source records attributed to Cuevas, Andres.

At least 19 records

Investigation of Gallium–Boron Spin-On Codoping for poly-Si/SiO x Passivating Contacts

A doping technique for p-type poly-Si/SiOx passivating contacts using a spin-on method for different mixtures of Ga and B glass solutions is presented. Effects of solution mixing ratios on the contact performance (implied open circuit voltage iV oc , contact resistivity ..rho..c) are investigated. For all as-annealed samples at different drive-in temperatures, increasing the percentage of Ga in the solution shows a decrement in iV oc (from ~680 to ~610 mV) and increment in ..rho..c (from ~3 to ~800 mO cm 2 ). After a hydrogenation treatment by depositing a SiN x /AlO x stack followed by forming gas annealing, all samples show improved iVoc (~700 mV with Ga-B co-doped, and ~720 mV with all Ga). Interestingly, when co-doping Ga with B, even a small amount of B in the mixing solution shows negative effects on the surface passivation. Active and total dopant profiles obtained by electrical capacitance voltage and secondary-ion mass spectrometry measurements, respectively, reveal a relatively low percentage of electrically-active Ga and B in the poly-Si and Si layers. Overall, these results help understand the different features of the two dopants: a low ρ c with B, a good passivation with Ga, their degree of activation inside the poly-Si and Si layers, and the annealing effects.

14 SOLAR ENERGY↗

Morphology, microstructure, and doping behaviour: A comparison between different deposition methods for poly-Si/SiO x passivating contacts

In this work, we study how crystallographic structures, optoelectronic properties, and nanoscale surface morphologies of ex situ phosphorus-doped polycrystalline silicon (poly-Si)/SiO x passivating contacts, formed by different deposition methods (sputtering, plasma-enhanced chemical vapour deposition [PECVD], and low-pressure chemical vapour deposition [LPCVD]), are investigated and compared. Across all these deposition technologies, we noted the same trend: higher diffusion temperatures yield films that are more crystalline but that have rougher surface morphologies due to bigger surface crystal grains. Also, the recrystallization process of the as-deposited Si films starts from the SiO x interface, rather than from the film surface and bulk. However, there are some distinct differences among these technologies. First, the LPCVD method yields the lowest deposition rate, roughest surfaces, and smallest degree of crystallinity on finished poly-Si films. In contrast, the PECVD method has the highest deposition rate and smoothest surfaces for both as-deposited Si and annealed poly-Si films. Second, as-deposited sputtered and PECVD Si films contain only an amorphous phase, whereas as-deposited LPCVD films already has some crystalline phase. Third, the LPCVD phosphorus in-diffusion into the substrate depends strongly on the initial film thickness, whereas for the other two methods, it is weakly dependent on thickness. Finally, the passivation quality of every poly-Si film type has different responses to the film thickness and diffusion temperature, suggesting that the ex situ doping optimization should be performed independently.

14 SOLAR ENERGY↗

Deposition pressure dependent structural and optoelectronic properties of ex-situ boron-doped poly-Si/SiO x passivating contacts based on sputtered silicon

Among common methods to form polycrystalline silicon (poly-Si) films for passivating-contact solar cells, physical vapor deposition, in particular sputtering, is the safest one as it does not require any toxic gaseous precursors. One of the critical parameters to control the properties of sputtered silicon films is their deposition pressure. In this work, structural and optoelectronic characteristics of ex-situ boron-doped poly-Si/SiO x passivating contacts, formed from sputtered intrinsic amorphous silicon (a-Si) deposited at different pressures on top of SiO x /c-Si substrates and subjected to a high-temperature boron diffusion step, are investigated. The deposition rate and density of the as-deposited a-Si films increase with reducing pressure. Low-temperature photoluminescence spectra captured from the as-deposited samples at different pressures do not show typical emissions from hydrogenated a-Si. Meanwhile, their Fourier-transform infrared absorption spectra all show Si–H stretching modes, indicating that hydrogen had been initially incorporated into the chemical SiO x layers and eventually hydrogenated the a-Si/SiO x interfaces during the sputtering process. After the high-temperature boron-diffusion step, all hydrogen-related peaks disappear. Lower pressure films (1.5 and 2.5 mTorr) show more consistent improved performance after hydrogen treatments, compared to higher pressure films (4 and 5 mTorr). Overall, the resultant passivating contacts at 2.5 mTorr achieve a low single-side recombination current density Jo of ~9 fA/cm 2 , whereas their contact resistivity is still low at 15 mO cm 2 .

14 SOLAR ENERGY↗

Hydrogen-Assisted Defect Engineering of Doped Poly-Si Films for Passivating Contact Solar Cells

Hydrogen-assisted defect engineering, via a hydrogenated silicon nitride (SiN x :H) capping layer, on doped polycrystalline silicon (poly-Si) passivating-contact structures, is explored using complementary techniques. The hydrogen treatment universally improves the passivation quality of poly-Si/SiO x stacks on all samples investigated. Meanwhile, their contact resistivity remains very low at ~6 m$\Omega$cm 2 . Moreover, the nature of charge carrier recombination within the poly-Si films is also investigated by means of photoluminescence. On planar c-Si substrates, the poly-Si films emit two broad photoluminescence peaks ~850-1050 nm and ~1300-1500 nm. The former is the characteristic peak of the hydrogenated amorphous Si (a-Si:H) phase and only appears after the treatment, demonstrating that i) a significant amount of hydrogen has been driven into the poly-Si film and ii) an amorphous phase is present within it. The second peak originates from sub-bandgap radiative defects inside the poly-Si films and increases after the treatment, suggesting a suppression of their non-radiative recombination channels. For films deposited on textured c-Si substrates, there is a disrupted oxide boundary, preventing a build-up of excess carriers inside the films and leading to quenching of the film luminescence.

36 MATERIALS SCIENCE↗

Hydrogenation Mechanisms of Poly-Si/SiO x Passivating Contacts by Different Capping Layers

Herein, posttreatment techniques of phosphorus-doped poly-Si/SiO x passivating contacts, including forming gas annealing (FGA), atomic layer deposition (ALD) of hydrogenated aluminum oxide (AlO x :H), and plasma-enhanced chemical vapor deposition (PECVD) of hydrogenated silicon nitride (SiN x :H), are investigated and compared in terms of their application to silicon solar cells. A simple FGA posttreatment produces a significant increase in the implied open circuit voltage (iV oc ) and the effective minority-carrier lifetime (teff) of high-resistivity crystalline Si (c-Si) samples, whereas low-resistivity samples show a minimal change. Treatment by means of AlO x :H and/or SiN x :H followed by postdeposition FGA results in a universal increase in t eff and iV oc for all substrate resistivities (as high as 12.5 ms and 728 mV for 100 Ω cm and 5.4 ms and 727 mV for 2 Ω cm n-type c-Si substrates). In addition, both the FGA and AlO x :H + FGA techniques can inject sufficient hydrogen into the samples to passivate defects at the SiO x /c-Si and poly-Si/SiO x interfaces. However, this hydrogen concentration is insufficient to neutralize both the nonradiative defects inside the poly-Si films and dangling bonds associated with the amorphous Si phase present in them. The hydrogen injected by the SiN x :H + FGA technique can passivate both the interfaces and the defects and dangling bonds within the poly-Si film. These results are confirmed by low-temperature photoluminescence spectroscopy, Fourier transform infrared spectroscopy, and dynamic secondary-ion mass spectrometry measurements.

14 SOLAR ENERGY↗

Dopant-Free Partial Rear Contacts Enabling 23% Silicon Solar Cells

Over the past five years, there has been a significant increase in both the intensity of research and the performance of crystalline silicon devices which utilize metal compounds to form carrier-selective heterocontacts. Such heterocontacts are less fundamentally limited and have the potential for lower costs compared to the current industry dominating heavily doped, directly metalized contacts. A low temperature (≤230 °C), TiO x /LiF x /Al electron heterocontact is presented here, which achieves mΩcm 2 scale contact resistivities ρ c on lowly doped n-type substrates. Here, as an extreme demonstration of the potential of this heterocontact, it is trialed in a newly developed, high efficiency n-type solar cell architecture as a partial rear contact (PRC). Despite only contacting ≈1% of the rear surface area, an efficiency of greater than 23% is achieved, setting a new benchmark for n-type solar cells featuring undoped PRCs and confirming the unusually low ρ c of the TiO x /LiF x /Al contact. Finally, in contrast to previous versions of the n-type undoped PRC cell, the performance of this cell is maintained after annealing at 350–400 °C, suggesting its compatibility with conventional surface passivation activation and sintering steps.

14 SOLAR ENERGY↗

Sub-Bandgap Luminescence from Doped Polycrystalline and Amorphous Silicon Films and Its Application to Understanding Passivating-Contact Solar Cells

We report luminescence phenomena from doped polycrystalline silicon (poly-Si) films and their applications to study carrier transport properties in passivating-contact solar cells. Low-temperature luminescence spectra emitted from doped poly-Si layers are found to be very broad and stretched from the crystalline silicon (c-Si) luminescence peak to significantly lower energies. This suggests that these layers contain radiative defect levels whose energies are continuously distributed from the band edges to deep levels in the poly-Si bandgap. Moreover, photoinduced carriers inside poly-Si layers are found to be completely blocked by an ultrathin SiOx interlayer (~1.3 nm). This demonstrates that there is no free-carrier coupling from poly-Si layers in practical passivating-contact solar cells. Finally, we demonstrate that the same principle can be applied to study carrier transport properties in hydrogenated amorphous silicon films.

14 SOLAR ENERGY↗

23% efficient n-type crystalline silicon solar cells with passivated partial rear contacts

© 2018 IEEE. Over the past three years a new family of high efficiency n-type crystalline silicon cells featuring passivated partial rear contacts (PRC) has emerged. These cells take advantage of the unique contact properties obtained by introducing thin metal compound interlayers, such as TiO x and LiFx, between the metallic electrode and the silicon absorber. This paper explores the concept and potential advantages of the n-type passivated PRC cell. In particular, the recent fabrication of a cell at 23.1%, featuring a less-than 1% TiOx/LiFx /Al passivated PRC, demonstrates the compatibility of this concept with high efficiency designs.

Bullock, James↗

Temperature and Humidity Stable Alkali/Alkaline-Earth Metal Carbonates as Electron Heterocontacts for Silicon Photovoltaics

Nanometer scale interfacial layers between the metal cathode and the n-type semiconductor play a critical role in enhancing the transport of charge carriers in and out of optoelectronic devices. In this research, a range of nanoscale alkali and alkaline earth metal carbonates (i.e., potassium, rubidium, caesium, calcium, strontium, and barium) are shown to function effectively as electron heterocontacts to lightly doped n-type crystalline silicon (c-Si), which is particularly challenging to contact with common metals. These carbonate interlayers are shown to enhance the performance of n-type c-Si proof-of-concept solar cells up to a power conversion efficiency of ≈19%. Furthermore, these devices are thermally stable up to 350 °C and both the caesium and barium carbonates pass a standard 1000 h damp heat test, with >95% of their initial performance maintained. The temperature and humidity stable electron heterocontacts based on alkali and alkaline earth metal carbonates show a high potential for industrial feasibility and longevity for deployment in the field.

36 MATERIALS SCIENCE↗

Zirconium oxide surface passivation of crystalline silicon

This letter reports effective passivation of crystalline silicon (c-Si) surfaces by thermal atomic layer deposited zirconium oxide (ZrO x ). The optimum layer thickness and activation annealing conditions are determined to be 20 nm and 300 °C for 20 min. Cross-sectional transmission electron microscopy imaging shows an approximately 1.6 nm thick SiO x interfacial layer underneath an 18 nm ZrO x layer, consistent with ellipsometry measurements (~20 nm). Capacitance-voltage measurements show that the annealed ZrO x film features a low interface defect density of 1.0 × 10 11 cm -2 eV -1 and a low negative film charge density of -6 × 10 10 cm -2 . Effective lifetimes of 673 μs and 1.1 ms are achieved on p-type and n-type 1 Ω cm undiffused c-Si wafers, respectively, corresponding to an implied open circuit voltage above 720 mV in both cases. The results demonstrate that surface passivation quality provided by ALD ZrO x is consistent with the requirements of high efficiency silicon solar cells.

36 MATERIALS SCIENCE↗

Stable Dopant-Free Asymmetric Heterocontact Silicon Solar Cells with Efficiencies above 20%

Development of new device architectures and process technologies is of tremendous interest in crystalline silicon (c-Si) photovoltaics to drive enhanced performance and/or reduced processing cost. In this regard, an emerging concept with a high-efficiency potential is to employ low/high work function metal compounds or organic materials to form asymmetric electron and hole heterocontacts. Here, this Letter demonstrates two important milestones in advancing this burgeoning concept. First, a high-performance, low-temperature, electron-selective heterocontact is developed, comprised of a surface passivating a -Si:H layer, a protective TiO x interlayer, and a low work function LiF x /Al outer electrode. This is combined with a MoO x hole-selective heterocontact to demonstrate a cell efficiency of 20.7%, the highest value for this cell class to date. Second, we show that this cell passes a standard stability test by maintaining >95% of its original performance after 1000 h of unencapsulated damp heat exposure, indicating its potential for longevity.

14 SOLAR ENERGY↗

Tantalum Oxide Electron-Selective Heterocontacts for Silicon Photovoltaics and Photoelectrochemical Water Reduction

Crystalline silicon (c-Si) solar cells have been dominating the photovoltaic (PV) market for decades, and c-Si based photoelectrochemical (PEC) cells are regarded as one of the most promising routes for water splitting and renewable production of hydrogen. Here, we demonstrate a nanoscale tantalum oxide (TaO x , ~6 nm) as an electron-selective heterocontact, simultaneously providing high-quality passivation to the silicon surface and effective transport of electrons to either an external circuit or a water-splitting catalyst. The PV application of TaO x is demonstrated by a proof-of-concept device having a conversion efficiency of 19.1%. In addition, the PEC application is demonstrated by a photon-to-current efficiency (with additional applied bias) of 7.7%. These results represent a 2% and 3.8% absolute enhancement over control devices without a TaO x interlayer, respectively. The methods presented in this Letter are not limited to c-Si based devices and can be viewed as a more general approach to the interface engineering of optoelectronic and photoelectrochemical applications.

14 SOLAR ENERGY↗

Microchannel contacting of crystalline silicon solar cells

There is tremendous interest in reducing losses caused by the metal contacts in silicon photovoltaics, particularly the optical and resistive losses of the front metal grid. One commonly sought-after goal is the creation of high aspect-ratio metal fingers which provide an optically narrow and low resistance pathway to the external circuit. Currently, the most widely used metal contact deposition techniques are limited to widths and aspect-ratios of ~40 μm and ~0.5, respectively. In this study, we introduce the use of a micropatterned polydimethylsiloxane encapsulation layer to form narrow (~20 μm) microchannels, with aspect-ratios up to 8, on the surface of solar cells. We demonstrate that low temperature metal pastes, electroless plating and atomic layer deposition can all be used within the microchannels. Further, we fabricate proof-of-concept structures including simple planar silicon heterojunction and homojunction solar cells. While preliminary in both design and efficiency, these results demonstrate the potential of this approach and its compatibility with current solar cell architectures.

14 SOLAR ENERGY↗

Conductive and Stable Magnesium Oxide Electron-Selective Contacts for Efficient Silicon Solar Cells

A high Schottky barrier (>0.65 eV) for electrons is typically found on lightly doped n–type crystalline (c–Si) wafers for a variety of contact metals. This behavior is commonly attributed to the Fermi–level pinning effect and has hindered the development of n–type c–Si solar cells, while its p–type counterparts have been commercialized for several decades, typically utilizing aluminium alloys in full–area, and more recently, partial–area rear contact configurations. Here the authors demonstrate a highly conductive and thermally stable electrode composed of a magnesium oxide/aluminium (MgOx/Al) contact, achieving moderately low resistivity Ohmic contacts on lightly doped n–type c–Si. The electrode, functionalized with nanoscale MgO x films, significantly enhances the performance of n–type c–Si solar cells to a power conversion efficiency of 20%, advancing n–type c–Si solar cells with full–area dopant–free rear contacts to a point of competitiveness with the standard p–type architecture. Here, the low thermal budget of the cathode formation, its dopant–free nature, and the simplicity of the device structure enabled by the MgO x /Al contact open up new possibilities in designing and fabricating low–cost optoelectronic devices, including solar cells, thin film transistors, or light emitting diodes.

36 MATERIALS SCIENCE↗

Low resistance Ohmic contact to p-type crystalline silicon via nitrogen-doped copper oxide films

This work explores the application of transparent nitrogen doped copper oxide (CuO{sub x}:N) films deposited by reactive sputtering to create hole-selective contacts for p-type crystalline silicon (c-Si) solar cells. It is found that CuO{sub x}:N sputtered directly onto crystalline silicon is able to form an Ohmic contact. X-ray photoelectron spectroscopy and Raman spectroscopy measurements are used to characterise the structural and physical properties of the CuO{sub x}:N films. Both the oxygen flow rate and the substrate temperature during deposition have a significant impact on the film composition, as well as on the resulting contact resistivity. After optimization, a low contact resistivity of ∼10 mΩ cm{sup 2} has been established. This result offers significant advantages over conventional contact structures in terms of carrier transport and device fabrication.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Passivation of c-Si surfaces by sub-nm amorphous silicon capped with silicon nitride

A sub-nm hydrogenated amorphous silicon (a-Si:H) film capped with silicon nitride (SiN{sub x}) is shown to provide a high level passivation to crystalline silicon (c-Si) surfaces. When passivated by a 0.8 nm a-Si:H/75 nm SiN{sub x} stack, recombination current density J{sub 0} values of 9, 11, 47, and 87 fA/cm{sup 2} are obtained on 10 Ω·cm n-type, 0.8 Ω·cm p-type, 160 Ω/sq phosphorus-diffused, and 120 Ω/sq boron-diffused silicon surfaces, respectively. The J{sub 0} on n-type 10 Ω·cm wafers is further reduced to 2.5 ± 0.5 fA/cm{sup 2} when the a-Si:H film thickness exceeds 2.5 nm. The passivation by the sub-nm a-Si:H/SiN{sub x} stack is thermally stable at 400 °C in N{sub 2} for 60 min on all four c-Si surfaces. Capacitance–voltage measurements reveal a reduction in interface defect density and film charge density with an increase in a-Si:H thickness. The nearly transparent sub-nm a-Si:H/SiN{sub x} stack is thus demonstrated to be a promising surface passivation and antireflection coating suitable for all types of surfaces encountered in high efficiency c-Si solar cells.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Tantalum oxide/silicon nitride: A negatively charged surface passivation stack for silicon solar cells

This letter reports effective passivation of crystalline silicon (c-Si) surfaces by thermal atomic layer deposited tantalum oxide (Ta{sub 2}O{sub 5}) underneath plasma enhanced chemical vapour deposited silicon nitride (SiN{sub x}). Cross-sectional transmission electron microscopy imaging shows an approximately 2 nm thick interfacial layer between Ta{sub 2}O{sub 5} and c-Si. Surface recombination velocities as low as 5.0 cm/s and 3.2 cm/s are attained on p-type 0.8 Ω·cm and n-type 1.0 Ω·cm c-Si wafers, respectively. Recombination current densities of 25 fA/cm{sup 2} and 68 fA/cm{sup 2} are measured on 150 Ω/sq boron-diffused p{sup +} and 120 Ω/sq phosphorus-diffused n{sup +} c-Si, respectively. Capacitance–voltage measurements reveal a negative fixed insulator charge density of −1.8 × 10{sup 12 }cm{sup −2} for the Ta{sub 2}O{sub 5} film and −1.0 × 10{sup 12 }cm{sup −2} for the Ta{sub 2}O{sub 5}/SiN{sub x} stack. The Ta{sub 2}O{sub 5}/SiN{sub x} stack is demonstrated to be an excellent candidate for surface passivation of high efficiency silicon solar cells.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Recombination and thin film properties of silicon nitride and amorphous silicon passivated c-Si following ammonia plasma exposure

Recombination at silicon nitride (SiN{sub x}) and amorphous silicon (a-Si) passivated crystalline silicon (c-Si) surfaces is shown to increase significantly following an ammonia (NH{sub 3}) plasma exposure at room temperature. The effect of plasma exposure on chemical structure, refractive index, permittivity, and electronic properties of the thin films is also investigated. It is found that the NH{sub 3} plasma exposure causes (i) an increase in the density of Si≡N{sub 3} groups in both SiN{sub x} and a-Si films, (ii) a reduction in refractive index and permittivity, (iii) an increase in the density of defects at the SiN{sub x}/c-Si interface, and (iv) a reduction in the density of positive charge in SiN{sub x}. The changes in recombination and thin film properties are likely due to an insertion of N–H radicals into the bulk of SiN{sub x} or a-Si. It is therefore important for device performance to minimize NH{sub 3} plasma exposure of SiN{sub x} or a-Si passivating films during subsequent fabrication steps.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗