Search NASA⌕ Search

Engineering topics

Cui, Jun

Publications and source records attributed to Cui, Jun.

At least 73 records · Page 4

The application of macroscopic flakes for Fe-6.5%Si bulk magnetics with superior magnetic properties

Silicon steel is the most popular crystalline soft magnetic material for motor and transformer applications. The material must be in thin thickness to reduce the eddy current loss. Conventional thin steel sheet manufacturing process starts with cast slab, followed by a series of hot/cold roll process. For transformer, thin sheet is wrapped to form the core; for motor, the sheet is stamped, coated, heat treated, and stacked to form stator/rotor. This process requires the steel to possess sufficient ductility. For Si steel, increasing Si content will improve its electrical and magnetic properties, but it will also lead to embrittlement with 3.5% Si as the limit for the conventional manufacturing processes. Despite poor mechanical properties, high Si steel, especially the one with 6.5% Si, is gaining more attention due to its lower iron loss, higher permeability, and near zero magnetostriction. To address the brittleness problem of the 6.5% Si steel, we developed a novel process, using rapid solidification to prepare thin flakes with high ductility, then using hot press to consolidate the flakes into near net shape bulk sample. The obtained Fe-6.5%Si sample with 0.2 mm thickness exhibits an iron loss of 7.2 W/kg at 400Hz and magnetic flux density of 1 Tesla, and a maximum permeability of 28,400. In addition, various coating materials and processes were investigated as inter-flake insulators for their effect on reducing the eddy current losses for thicker configuration.

Fe-6.5%Si Steel↗

The application of macroscopic flakes for Fe-6.5%Si bulk magnetics with superior magnetic properties

Inductors are used in power electronics to convert current to different frequency and voltage. They are used extensively from where power is generated all the way to electric vehicles and portable electronic devices. The soft magnetic materials used in the inductors is critical for the performance of the inductors. Currently, a majority of the inductor uses powder core. The use of powder is not ideal as the 3D granule powders generate large demagnetization field working against the applied field, resulting in reduced permeability and efficiency. In this paper, 2D flakes were used to replace the 3D granules as the feedstock for fabricating inductor core. The crystalline Fe-Si based crystalline soft magnetic material in the form of flakes approximately 0.1mm thick, 1mm long and 2mm wide were prepared via melt spinning. The flakes were then coated with insulating materials before compacted into a toroid. The effect of coating thickness and concentration on magnetic properties of the toroidal sample are studied. It was also found that the magnetic cores made by flakes surpass the cores made by same size powder with larger permeability and lower iron losses.

Fe-6.5%Si Steel↗

SpWRKY6 acts as a positive regulator during tomato resistance to Phytophthora infestans infection

Highlights: • SpWRKY6 acts as a positive regulator of tomato resistance to P. infestans infection. • Over-expressing SpWRKY6 tomato increased resistance to P. infestans by scavenging reactive oxygen species. • SpWRKY6-mediated tomato resistance to P. infestans through regulating the expression level of PR genes. WRKY transcription factors have been widely known to play key regulatory roles in plant disease resistance. In our previous study, characteristics of SpWRKY6 and its role in response to biotic and abiotic stress was studied. To further investigate the function of SpWRKY6 in tomato resistance to Phytophthora infestans (P. infestans), we studied the effects of loss and gain of function of SpWRKY6. Inhibition of SpWRKY6 mRNA accumulation in tomato leaves, using virus-induced gene silencing (VIGS), greatly reduced SpWRKY6 mRNA levels, and compromised tomato resistance to P. infestans. In contrast, overexpressing- SpWRKY6 tomato plants showed enhanced resistance to P. infestans, accompanied by decreased number of necrotic cells, lesion sizes and disease index. Furthermore, after P. infestans infection, the expression levels of pathogenesis related (PR) genes in transgenic tomato plants overexpressed SpWRKY6 were significantly higher than those in wild type plants, while the number of necrotic cells and the reactive oxygen species (ROS) accumulation were fewer and lower. Taken together, these results indicating that SpWRKY6 acts as a positive regulator of tomato resistance to P. infestans infection through regulating the ROS level and the expression level of PR genes along with alleviating cell membrane injury.

60 APPLIED LIFE SCIENCES↗

Thermoelastic cooling

A cooling system based on thermoelastic effect is provided. The system comprises a heat sink, a refrigerated space and a regenerator coupled to the refrigerated space and to the heat sink to pump heat from the refrigerated space to the heat sink. The regenerator comprises solid thermoelastic refrigerant materials capable of absorbing or releasing heat.

Cui, Jun↗

System and process for friction consolidation fabrication of permanent magnets and other extrusion and non-extrusion structures

A die tool and process are described that provide friction consolidation fabrication and friction consolidation extrusion fabrication products including permanent magnets, and other extrusion and non-extrusion structures. The present invention overcomes previous particle size, texture, homogeneity and density limitations in conventional metallurgy processes.

42 ENGINEERING↗

Ultra-low-field magneto-elastocaloric cooling in a multiferroic composite device

Abstract The advent of caloric materials for magnetocaloric, electrocaloric, and elastocaloric cooling is changing the landscape of solid state cooling technologies with potentials for high-efficiency and environmentally friendly residential and commercial cooling and heat-pumping applications. Given that caloric materials are ferroic materials that undergo first (or second) order phase transitions near room temperature, they open up intriguing possibilities for multiferroic devices with hitherto unexplored functionalities coupling their thermal properties with different fields (magnetic, electric, and stress) through composite configurations. Here we demonstrate a magneto-elastocaloric effect with ultra-low magnetic field (0.16 T) in a compact geometry to generate a cooling temperature change as large as 4 K using a magnetostriction/superelastic alloy composite. Such composite systems can be used to circumvent shortcomings of existing technologies such as the need for high-stress actuation mechanism for elastocaloric materials and the high magnetic field requirement of magnetocaloric materials, while enabling new applications such as compact remote cooling devices.

36 MATERIALS SCIENCE↗

Thermodynamic and kinetic analysis of the melt spinning process of Fe-6.5 wt.% Si alloy

Here, the microstructural evolution of Fe-6.5 wt.% Si alloy during rapid solidification was studied over a quenching rate of 4 × 10 4 K/s to 8 ×10 5 K/s. The solidification and solid-state diffusional transformation processes during rapid cooling were analyzed via thermodynamic and kinetic calculations. The Allen-Cahn theory was adapted to model the experimentally measured bcc_B2 antiphase domain sizes under different cooling rates. The model was calibrated based on the experimentally determined bcc_B2 antiphase domain sizes for different wheel speeds and the resulting cooling rates. Good correspondence of the theoretical and experimental data was obtained over the entire experimental range of cooling rates. Along with the asymptotic domain size value at the infinite cooling rates, the developed model represents a reliable extrapolation for the cooling rate > 10 6 K/s and allows one to optimize the quenching process.

36 MATERIALS SCIENCE↗

Characterization of Bypass Fluid Flow in an Active Magnetic Regenerative Liqueer

Active magnetic regenerators (AMR) with second order magnetocaloric materials operating below the Curie temperature have a unique property where the magnetized specific heat is lower than the demagnetized specific heat. The associated thermal mass unbalance allows a fraction of heat transfer fluid in the cold heat exchanger to bypass the magnetized regenerator. This cold bypassed fluid can precool a process stream as it returns to the hot side, thereby increasing the efficiency of liquefaction and reducing the cost of liquid cryogens. While researchers have been aware of this phenomenon for decades, experimental performance improvements from bypass fluid flow have yet to be reported in open literature. In the present work, the net cooling power of an active magnetic regenerative liquefier is investigated as a function of the bypass ow fraction. Experiments are performed at a fixed temperature span that yield a 25% improvement in net cooling power, affirming the potential of bypass cooling power.

active magnetic regenerator, hydrogen, liquefacati↗

Overcoming fatigue through compression for advanced elastocaloric cooling

Elastocaloric materials exhibit extraordinary cooling potential, but the repetition of cyclic mechanical loadings during long-term operation of cooling systems requires the refrigerant material to have long fatigue life. Here, this paper reviews the fundamental cause of fatigue from aspects of initiation and propagation of fatigue cracks in shape-memory alloys (SMAs) that are used as elastocaloric materials, and highlights recent advances in using compression to overcome fatigue by curtailing the generation of surfaces associated with crack propagation. Compression is identified as a key means to extend fatigue lifetime in engineering design of elastocaloric cooling drive mechanisms. We summarize the state-of-the-art performance of different SMAs as elastocaloric materials and discuss the influence of low cyclic strains and high resistance to transformation. We present integration of compression-based material assemblies into a cooling system prototype and optimization of the system efficiency using work recovery and related measures.

36 MATERIALS SCIENCE↗

Effect of cooling rate on the magnetic and mechanical properties of melt spun Fe-6.5 wt.% electric steel

The superior magnetic and electric properties of 6.5 wt.% high silicon steel may improve efficiency and power density of electric machines. However, the brittleness due to the formation of B2 and D03 ordered phases make it difficult for the application of high silicon steel. These ordered phases can be fully or partially suppressed by rapid cooling. However, further study is needed to understand the effect of cooling rate on magnetic and mechanical properties. By tuning the melt spinning wheel speed from 1m/s to 30m/s, varying degrees of cooling rate were achieved. The obtained ribbons with various degree of ordering were tested for mechanical, magnetic and electrical properties. The correlation between the cooling rate, ordering, and physical properties are established.

36 MATERIALS SCIENCE↗

Effect of wheel speed on magnetic and mechanical properties of melt spun Fe-6.5 wt.% Si high silicon steel

Here, Fe-Si electric steel is the most widely used soft magnetic material in electric machines and transformers. Increasing the silicon content from 3.2 wt.% to 6.5 wt.% brings about large improvement in the magnetic and electrical properties. However, 6.5 wt.% silicon steel is inherited with brittleness owing to the formation of B2 and D0 3 ordered phase. To obtain ductility in Fe-6.5wt.% silicon steel, the ordered phase has to be bypassed with methods like rapid cooling. In present paper, the effect of cooling rate on magnetic and mechanical properties of Fe-6.5wt.% silicon steel is studied by tuning the wheel speed during melt spinning process. The cooling rate significantly alters the ordering and microstructure, and thus the mechanical and magnetic properties. X-ray diffraction data shows that D0 3 ordering was fully suppressed at high wheel speeds but starts to nucleate at 10m/s and below, which correlates with the increase of Young’s modulus towards low wheel speeds as tested by nanoindentation. The grain sizes of the ribbons on the wheel side decrease with increasing wheel speeds, ranging from ~100 μm at 1m/s to ~8 μm at 30m/s, which lead to changes in coercivity.

36 MATERIALS SCIENCE↗

Effect of wheel speed on the magnetic and mechanical properties of melt spun Fe-6.5 wt.% electric steel

Fe-Si electric steel is the most widely used soft magnetic materials in electric mahines and motors, transformers and generators. Improving the surperior magnetic and electric properties of 6.5 wt.% high silicon steel is essential for higher may improve energy efficiency and power density of electric machines. However, the brittleness due to the formation of B2 and D03 ordered phases in high silicon steel make it difficult forbids for the application of high silicon steel. It is known that these ordered phases can be fully or partially suppressed by rapid cooling. However, further study is needed to understand the extend of cooling on the magnetic and mechanical properties of 6.5 wt.% silicon steel with various degree of ordering. By tuning the wheel speed from 1m/s to 30m/s with several intervals of the melt spinning process, varying degrees of cooling were achieved on 6.5 wt.% silicon steel ribbons. The cooling rate significant altered the ordering, microstructure size scale, and thus the mechanical and magnetic properties. TEM results showed that D03 ordering can be fully suppressed at high wheel speed, but started to nucleate at 5m/s and below, which correlates with the hardness and Young’s modulus increase towards low wheel speeds as tested by micro and nano indentation. The grain sizes of the ribbons on the wheel side decreased with increasing wheel speeds being ~100 micron at 1m/s and ~8 micron at 30m/s, which led to the change in coercivity. Saturation magnetization and electric resistivity of the ribbons remained about 190 emu/g and 84 microhm *cm, which appeared to be mainly depend on the chemistry.

Fe-6.5%Si Steel↗

Elastocaloric cooling of additive manufactured shape memory alloys with large latent heat

The stress-induced martensitic phase transformation of shape memory alloys (SMAs) is the basis for elastocaloric cooling. In this paper, we employ additive manufacturing to fabricate TiNi SMAs, and demonstrate compressive elastocaloric cooling in the TiNi rods with transformation latent heat as large as 20 J g -1 . Adiabatic compression on as-fabricated TiNi displays cooling ΔT as high as -7.5 °C with recoverable superelastic strain up to 5%. Unlike conventional SMAs, additive manufactured TiNi SMAs exhibit linear superelasticity with narrow hysteresis in stress–strain curves under both adiabatic and isothermal conditions. Microstructurally, we find that there are Ti 2 Ni precipitates typically one micron in size with a large aspect ratio enclosing the TiNi matrix. Finally, a stress transfer mechanism between reversible phase transformation in the TiNi matrix and mechanical deformation in Ti 2 Ni precipitates is believed to be the origin of the unique superelasticity behavior.

36 MATERIALS SCIENCE↗

Effects of Cooling Rate on 6.5% Silicon Steel Ordering

Increasing Si content improves magnetic and electrical properties of electrical steel, with 6.5% Si as the optimum. Unfortunately, when Si content approaches 5.7%, the Fe-Si alloy becomes brittle. At 6.5%, the steel conventional cold rolling process is no longer applicable. The heterogeneous formation of B2 and D03 ordered phases is responsible for the embrittlement. The formation of these ordered phases can be impeded by rapid cooling. However, only the cooling rates of water and brine water were investigated. A comprehensive study of the effect of rapid cooling rate on the formation of the ordered phases was carried out by varying wheel speed and melt-injection rate. Thermal imaging employed to measure cooling rates while microstructures of the obtained ribbons are characterized using X-ray diffraction and TEM. The electrical, magnetic and mechanical properties are characterized using 4-pt probe, VSM, and macro-indentation methods. The relations between physical properties and ordered phases are established.

36 MATERIALS SCIENCE↗

Effects of Cooling Rate on 6.5% Silicon Steel Ordering

Increasing Si content improves magnetic and electrical properties of electrical steel, with 6.5% Si as the optimum. Unfortunately, when Si content approaches 5.7%, the Fe-Si alloy becomes brittle. At 6.5%, the steel is so brittle that a conventional cold rolling process is no longer applicable. The heterogeneous formation of B2 and D03 ordered phases is responsible for the severe material embrittlement. Studies show that the formation of these ordered phases can be impeded by rapid cooling. However, due to the availability of quenching media, only the cooling rates of water and brine water were investigated. At Ames Laboratory, a comprehensive study of the effect of rapid cooling rate on the formation of the ordered phases was carried out. Melt spin method was used to prepare thick steel ribbon. A wide range of cooling rates was achieved by varying wheel speed and melt-injection rate. A calibrated high-resolution thermal camera was used to measure temperature changes during solidification. The microstructures of the obtained ribbons were characterized using X-ray diffraction and TEM. The electrical, magnetic and mechanical properties were characterized using 4-pt probe, VSM, and macro-indentation methods. The relations between these physical properties and ordered phases were established.

36 MATERIALS SCIENCE↗

Element-resolved magnetism across the temperature- and pressure-induced spin reorientation in MnBi

Rare-earth free permanent magnet MnBi (NiAs-type crystal structure) displays strong magnetic anisotropy above its 90 K spin reorientation transition (SRT). X-ray magnetic circular dichroism (XMCD) shows induced magnetism in Bi 5d band, which is strongly coupled to the magnetism of Mn. A clear increase in Bi orbital-to-spin moment ratio is observed above the SRT. Hydrostatic pressure mimics the e*ect of temperature on the SRT, and the pressure effect also leads to anisotropic lattice contraction, which is known to be induced by cooling. These results reveal that temperature and pressure can similarly induce the coupled structural and magnetic responses, suggesting the importance of the anisotropic lattice change and Mn-Bi hybridization to the magnetic anisotropy change across the SRT.

36 MATERIALS SCIENCE↗