Search NASA⌕ Search

Engineering topics

Curran, Scott

Publications and source records attributed to Curran, Scott.

At least 37 records · Page 2

IJER editorial: The future of the internal combustion engine

Internal combustion (IC) engines operating on fossil fuel oil provide about 25% of the world’s power (about 3000 out of 13,000 million tons oil equivalent per year—see Figure 1), and in doing so, they produce about 10% of the world’s greenhouse gas (GHG) emissions (Figure 2). Reducing fuel consumption and emissions has been the goal of engine researchers and manufacturers for years, as can be seen in the two decades of ground-breaking peer-reviewed articles published in this International Journal of Engine Research (IJER). Indeed, major advances have been made, making today’s IC engine a technological marvel. However, recently, the reputation of IC engines has been dealt a severe blow by emission scandals that threaten the ability of this technology to make significant and further contributions to the reduction of transportation sector emissions. In response, there have been proposals to replace vehicle IC engines with electric-drives with the intended goals of further reducing fuel consumption and emissions, and to decrease vehicle GHG emissions.

33 ADVANCED PROPULSION SYSTEMS↗

Fundamental Advancements in Pre-Chamber Spark Ignition and Emissions Control for Natural Gas Engines

Argonne National Laboratory, the National Renewable Energy Laboratory, Oak Ridge National Laboratory, and Sandia National Laboratories collaborated on research to address barriers for natural gas engine efficiency. This research project focuses on early stage research focusing on pre-chamber spark-ignition (PCSI) to achieve diesel-like efficiency in medium- and heavy-duty natural gas engines by extending the lean dilution limit and/or exhaust gas recirculation (EGR) dilution limit, as well as shortening burn duration, with integrated aftertreatment. This project integrates experimental and simulation based tasks to address four key barriers to market penetration of PCSI for medium- and heavy-duty natural gas engines. These include Inadequate science base and simulation tools to describe/predict the fluid-mechanical and chemical-kinetic processes governing PCSI to enable engineers in industry to optimize designs for efficiency, noise, reliability, pollutant formation, emissions control integration, and drivability; limited ability to extend EGR and/or lean dilution limits at higher loads; increased propensity for PCSI hot-spot pre-ignition at high loads relative to spark ignition; and ineffective methane catalysts for the high engine-out unburned fuel concentrations coupled with low exhaust temperatures (<<400 degrees C) of high efficiency engines.

33 ADVANCED PROPULSION SYSTEMS↗

Ignition Delay in Low Temperature Combustion

Low temperature combustion (LTC) strategies present a means of reducing soot and oxides of nitrogen (NOx) emissions while simultaneously increasing efficiency relative to conventional combustion modes. By sufficiently premixing fuel and air before combustion, LTC strategies avoid high fuel-to-air equivalence ratios that lead to soot production. Dilution of the mixture lowers the combustion temperatures to reduce NOx production and offers thermodynamic advantages for improved efficiency. However, issues such as high heat release rates (HRRs), incomplete combustion, and difficulty in controlling the timing of combustion arise with low equivalence ratios and combustion temperatures. Ignition delay (the time until the start of combustion) is a way to quantify the time available for fuel and air to mix inside the cylinder before combustion. Previous studies have used ignition delay to explain trends seen in LTC such as combustion stability and HRRs. This study provides a novel method of integrating ignition delay into the investigation of LTC to determine what insights ignition delay calculations can provide for the different challenges associated with LTC strategies. To eliminate the need for large chemical kinetic models and interpolation to predict ignition delay, an ignition delay correlation is used. The flexibility gained using the correlation allows this method to be quickly adapted to target different LTC strategies and challenges. In this work, three cases of low temperature gasoline combustion (LTGC) with varying stratification levels were evaluated with an emphasis on the non-monotonic trend of the HRRs. The described method for ignition delay calculation is used to detail the stratification and ignition delay distributions for each case and provide insight into the observed trends.

Drallmeier, Joseph↗

Fuel economy and emissions testing of an RCCI series hybrid vehicle

In the current work, a series hybrid vehicle has been constructed that utilises a dual-fuel, reactivity controlled compression ignition (RCCI) engine. Full vehicle testing was conducted on chassis dynamometers over the US Environmental Protection Agency Federal Test Procedure, Highway Fuel Economy Test and US06 using RCCI combustion with commercially available gasoline and ultra-low sulphur diesel. Fuel economy and emissions data were recorded over the specified test cycles. Testing revealed that engine-out emissions were similar to steady-state dynamometer engine testing. However, tailpipe-out emissions saw a reduction of HC and CO during the HWFET of 98.5%. Fuel economy was lower than expected due to the higher drivetrain losses of the series hybrid drivetrain. Finally, simulated changes to the drivetrain showed that it may be possible to increase fuel economy significantly, while meeting EPA emissions standards.

33 ADVANCED PROPULSION SYSTEMS↗

Spray-Wall Interactions in a Small-Bore, Multi-Cylinder Engine Operating With Reactivity-Controlled Compression Ignition

Experimental work on reactivity-controlled compression ignition (RCCI) in a small-bore, multi-cylinder engine operating on premixed iso-octane and direct-injected n-heptane has shown an unexpected combustion phasing advance at early injection timings, which has not been observed in large-bore engines operating under RCCI at similar conditions. In this work, computational fluid dynamics (CFD) simulations were performed to investigate whether spray-wall interactions could be responsible for this result. Comparison of the spray penetration, fuel film mass, and in-cylinder visualization of the spray from the CFD results to the experimentally measured combustion phasing and emissions provided compelling evidence of strong fuel impingement at injection timings earlier than -90 crank angle degrees (°CA) after top dead center (aTDC), and transition from partial to full impingement between -65 and -90°CA aTDC. Based on this evidence, explanations for the combustion phasing advance at early injection timings are proposed along with potential verification experiments.

Wissink, Martin L.↗

RCCI Combustion Regime Transitions in a Single-Cylinder Optical Engine and a Multi-Cylinder Metal Engine

We present that Reactivity Controlled Compression Ignition (RCCI) is an approach to increase engine efficiency and lower engine-out emissions by using in-cylinder stratification of fuels with differing reactivity (i.e., autoignition characteristics) to control combustion phasing. Stratification can be altered by varying the injection timing of the high-reactivity fuel, causing transitions across multiple regimes of combustion. When injection is sufficiently early, combustion approaches a highly-premixed autoignition regime, and when it is sufficiently late it approaches more mixing-controlled, diesel-like conditions. Engine performance, emissions, and control authority over combustion phasing with injection timing are most favorable in between, within the RCCI regime.To study charge preparation phenomena that dictate regime transitions, two different optical diagnostics are applied in a single-cylinder heavy-duty optical engine, and conventional engine diagnostics are applied in a multi-cylinder, light-duty all-metal engine. Both engines are operated with iso-octane and n-heptane as the low- and high-reactivity fuels, respectively. The iso-octane fuel fraction delivers 80% of the total fuel energy, the global equivalence ratio is 0.35, and no exhaust gas recirculation is used. In the optical engine, single-shot, band-pass infrared (IR) imaging of emission near 3.3 microns measures thermal C-H stretch-band emission of hot fuel vapor and intermediate combustion products, providing qualitative information about the fuel-vapor distribution and ignition locations during low-temperature heat release. Additionally, high-speed 7.2 kHz visible-light imaging of natural luminosity, optimized to detect chemiluminescence, indicates the spatial and temporal evolution of high-temperature heat release and combustion. Similar combustion regimes are observed for both engine platforms, allowing an opportunity for optical engine data to provide insight into fundamental phenomena affecting regime ranges and transitions in production engines. Key findings from imaging diagnostics indicate that at the late-injection limit of RCCI control authority, low-temperature ignition occurs when clearly identifiable jet structures are still intact, and during high-temperature combustion there is prevalent and persistent soot incandescence representative of locally mixing-limited (i.e., fuel-rich) combustion. Finally, at the early-injection limit of RCCI control, observed stratification during low-temperature ignition is subtle; however, high-temperature combustion still occurs sequentially from the bowl rim radially inwards.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Response Characteristics of a Stable Mixed Potential Ammonia Sensor in Simulated Diesel Exhaust

A mixed potential sensor using Au and Pt dense wire electrodes embedded between tape-casted layers of 8 mol% yttria stabilized zirconia (YSZ) was tested for application toward NH 3 , NO, NO 2 , C 3 H 6 and C 3 H 8 . In single-gas testing, the sensor exhibited the highest response toward NH 3 , while still exhibiting reasonably high sensitivity toward other interferent gases. We tested the sensor in a high-flow reactor at the National Transportation Research Center (NTRC) in order to simulate exhaust gas constituents and flow rates produced by lean-burn vehicles powered by Compression-Ignition Direct-Injection (CIDI), diesel engines. The sensor was characterized at 525 and 625°C for NH 3 , CO, C 3 H 6 , C 3 H 8 , and NO x in a base gas composition of 10% O 2 , 5% H 2 O, and 5% CO 2 flowing at 15 slpm. The sensor exhibited fast response time equal to the response time of the system's switching valve (T90<0.6s). Furthermore, in simulations of overdosing a selective catalytic reduction (SCR) system, the sensor was able to selectively respond to 20ppm injections of NH 3 slip despite the presence of the interferent gas species at combined concentrations ten times higher than that of the NH 3 . The laboratory sensor construct was transitioned to a pre-commercial, automotive stick sensor configuration that was demonstrated to retain the advantageous characteristics of the tape-cast device.

33 ADVANCED PROPULSION SYSTEMS↗

Summary Report on the SAE 2016 Range Extenders for Electric Vehicles Symposium

The SAE 2016 Range Extenders for Electric Vehicles Symposium was a 2-day technical meeting focused on the role of advanced internal combustion engines (ICEs) and other novel energy converter technologies for extending the range of electric vehicles (EVs). The first-of-its-kind symposium was notable for focusing solely on the range extender (REx) technologies and not the EVs. The technical program featured presentations from international leaders from industry, government, national laboratories, and academia. The opening keynote presentations covered a broad range of topics including consumer behavior, policy implications, regulatory considerations, and REx architectures as enablers for advanced technologies. The technical sessions focused on an array of REx technologies including conventional ICEs, as well as less conventional or emerging technologies such as microturbines, fuel cells, low-temperature combustion engines, and aluminum-air batteries. The symposium included two panel sessions. The trend toward increasing vehicle electrification and the changing role of ICEs and other auxiliary power unit technologies for use as REx’s is leading to new research and design development needs. The symposium captured the interest of the industry and research communities in exploring the opportunities and challenges associated with REx’s for EVs. This report includes key takeaways, summarized below, and draft notes for each presentation and panel discussion.

33 ADVANCED PROPULSION SYSTEMS↗

Response characteristics of stable mixed-potential NH 3 sensors in diesel engine exhaust

Here, a mixed-potential, electrochemical sensor platform is extended to NH 3 sensing by the introduction of a new gold alloy working electrode. A planar, pre-commercial NH 3 sensor utilized LANL’s controlled interface approach, and a Pd-Au alloy working electrode was tested in exhaust of a GM 1.9 L diesel engine downstream of a diesel oxidation catalyst through a slipstream arrangement. A fraction of the exhaust was pulled across the sensor with a pump at 20 L/min. In order to simulate NH 3 slip inside of a full SCR emissions control system, NH 3 was injected immediately upstream of the sensor using a calibrated mass flow controller. The sensor response quantitatively tracked the NH 3 as measured via Fourier transform infrared (FTIR) analyzer. A calibration curve was obtained in the exhaust from an ammonia staircase response with the engine running at steady-state engine conditions resulting in low background concentrations of NO x and HC (<20 ppm) during calibration. Exhaust gas recirculation (EGR) switching and sweeps were used to evaluate the NH 3 sensor response under different amounts of total background NO x . The calibration curve was used to directly compare the [NH 3 ] calculated from sensor response to the gas phase composition measured via FTIR. In general, there was excellent quantitative agreement between the sensor response and the actual NH 3 in the exhaust gas, and fast response time such that transients (<5 ppm) could be easily discerned from baseline. A LANL pre-commercial NO x sensor was tested simultaneously with the NH 3 sensor and the extent of cross-sensitivity between the two sensors will be discussed.

47 OTHER INSTRUMENTATION↗

Volatility characterization of nanoparticles from single and dual-fuel low temperature combustion in compression ignition engines

Our work explores the volatility of particles produced from two diesel low temperature combustion (LTC) modes proposed for high-efficiency compression ignition engines. It also explores mechanisms of particulate formation and growth upon dilution in the near-tailpipe environment. Moreover, the number distribution of exhaust particles from low- and mid-load dual-fuel reactivity controlled compression ignition (RCCI) and single-fuel premixed charge compression ignition (PPCI) modes were experimentally studied over a gradient of dilution temperature. Particle volatility of select particle diameters was investigated using volatility tandem differential mobility analysis (V-TDMA). Evaporation rates for exhaust particles were compared with V-TDMA results for candidate pure n-alkanes to identify species with similar volatility characteristics. The results show that LTC particles are mostly comprised of material with volatility similar to engine oil alkanes. V-TDMA results were used as inputs to an aerosol condensation and evaporation model to support the finding that smaller particles in the distribution are comprised of lower volatility material than large particles under primary dilution conditions. Although the results show that saturation levels are high enough to drive condensation of alkanes onto existing particles under the dilution conditions investigated, they are not high We conclude that observed particles from LTC operation must grow from low concentrations of highly non-volatile compounds present in the exhaust.

33 ADVANCED PROPULSION SYSTEMS↗

Additive Manufacturing Integrated Energy Demonstration

Meet AMIE - the Additive Manufacturing Integrated Energy demonstration project. Led by Oak Ridge National Laboratory and many industry partners, the AMIE project changes the way we think about generating, storing, and using electrical power. AMIE uses an integrated energy system that shares energy between a building and a vehicle. And, utilizing advanced manufacturing and rapid innovation, it only took one year from concept to launch.

3-D PRINTING↗

Summary of OEM Idling Recommendations from Vehicle Owner's Manuals

The project upon which this report is based was conceived in 2012 during discussions between the East Tennessee Clean Fuels Coalition (ETCleanFuels) and Oak Ridge National Laboratory (ORNL) who both noted that a detailed summary of idling recommendations for a wide variety of engines and vehicles were not available in the literature. The two organizations agreed that ETCleanFuels would develop a first-of-its-kind collection of idling recommendations from the owner’s manuals of modern production vehicles. Vehicle engine idling, a subject that has long been debated, is largely shrouded in misinformation. The justifications for idling seem to be many: driver comfort, waiting in lines, and talking on cell phones to name a few. Assuredly, a great number of people idle because of the myths and misinformation surrounding this issue. This report addresses these myths by turning to statements taken directly from the automobile and engine manufacturers themselves.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗