Search NASA⌕ Search

Engineering topics

Cyrus J. R. Kosztowny

Publications and source records attributed to Cyrus J. R. Kosztowny.

9 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2022

Buckling Test and Analysis of the 8-Foot-Diameter Sandwich Composite Cylinder Test Article CTA8.2 as Part of the Shell Buckling Knockdown Factor Project: Test Dates 5-7 December 2017

It is well known that the buckling response of thin shell structures can be sensitive to small imperfections in the geometry and loading. The NASA Engineering and Safety Center (NESC) Shell Buckling Knockdown Factor Project (SBKF) has the goal of developing buckling design recommendations for select classes of metallic and composite shells. Part of completed SBKF work is described in this report. In particular, the test and analysis results from the second SBKF composite test article, CTA8.2, are described. This test was the second in a series of tests on sandwich composite cylinders that can be used to experimentally validate analysis methods, which in turn can be used to develop analysis-based shell buckling design guidelines for sandwich composite launch-vehicle cylindrical structures. CTA8.2 was an 8-foot diameter honeycomb-core sandwich cylinder that was fabricated and tested at the Marshall Space Flight Center (MSFC). The primary objectives of this test were to interrogate the structural capability of the composite test article, and to verify the test-article design and analysis approach for cylinders subjected to axial compression loads. This report contains the descriptions of the test-article design, fabrication, and test. The pre-test modeling and analysis methods, and corresponding results used in support of the test-article design and test planning, are also described. Additional post-test modeling and analysis efforts and results follow. Selected test results are compared to pre-test predictions and post-test analyses.

Adam Przekop↗
NASA NTRS2022

Buckling Test and Analysis of the 8-foot-diameter Sandwich Composite Cylinder Test Article CTA8.3 as Part of the Shell Buckling Knockdown Factor Project: Test Dates 16~19 December 2019

This report describes work that is part of SBKF-the test and analysis results from the third SBKF cylindrical sandwich composite test article, which was designated SBKF-P3-CYL-CTA8.3. This test was the third in a series of tests on sandwich composite cylinders that can be used to experimentally validate analysis methods, which in turn can be used to develop analysis-based shell buckling design guidelines for sandwich composite launch-vehicle cylindrical structures. The primary objectives of this test were to interrogate the structural capability of the composite test article, and to verify the test-article design and analysis approach for cylinders subjected to axial compression and combined compression and bending loads.

Sandwich composite cylinder↗
NASA NTRSDate not supplied

Testing of a Composite Conical-Cylindrical Shell

Launch-vehicle shell structures, which can be comprised of both cylindrical and conical sections, are known to be susceptible to buckling due to their large radius-to-thickness ratios. The advancements in composite manufacturing and numerical methods have enabled designers to consider more nontraditional shapes, such as connecting the conical and cylindrical sections with a toroidal transition to create a single-piece conical-cylindrical shell. This single-piece construction eliminates the need for a heavy interface ring between sections and has the potential to save mass. To better understand the buckling behavior, a composite conical-cylindrical shell was designed, fabricated, and tested. Prior to test, a finite element model that included thickness variations and radial imperfections was created. The test article buckled elastically at 251.8 kN, approximately 8.8% higher than the predicted buckling load of 231.4 kN Continued research in conical-cylindrical structures has the potential to expand the design space for launch-vehicle structures and lead to improved designs and reduced weight.

Buckling↗
NASA NTRSDate not supplied

Test and Analysis of a Composite Conical-Cylindrical Shell

Launch-vehicle shell structures, which can be comprised of both cylindrical and conical sections, are known to be susceptible to buckling due to their large radius-to-thickness ratios. The advancements in composite manufacturing and numerical methods have enabled designers to consider more nontraditional shapes, such as connecting the conical and cylindrical sections with a toroidal transition to create a single-piece conical-cylindrical shell. This single-piece construction eliminates the need for a heavy interface ring between sections and has the potential to save mass. To better understand the buckling behavior, a composite conical-cylindrical shell was designed, fabricated, and tested. Prior to test, a finite element model that included thickness variations and radial imperfections was created. The test article buckled elastically at 251.8 kN, approximately 8.8% higher than the predicted buckling load of 231.4 kN Continued research in conical-cylindrical structures has the potential to expand the design space for launch-vehicle structures and lead to improved designs and reduced weight.

Buckling↗
NASA NTRSDate not supplied

The Effect of Fiber-Angle Fidelity on the Linear Response of Tow-steered Composite Plates

Composite laminate tailoring is traditionally performed by uniformly changing the in-plane ply orientation to obtain the desired mechanical performance. The emergence of tow-steered plies, where the fibers follow a prescribed curvilinear path, have increased the tailorability of composite laminates. However, characterizing the behavior of tow-steered laminates using finite element analysis is challenging because additional, and often numerous, orientation definitions may be required. The additional orientation definitions detrimentally increase the computational cost and hinder the use of advanced analysis techniques, such as Monte Carlo or uncertainty quantification, in the design process. To reduce computational cost without adversely affecting mechanics-based performance, the results of a parametric study that was used to investigate the effects of fiber-angle fidelity, element size, and tow-steered radius-of-curvature on various loading scenarios for tow-steered composite plates are presented. The three loading scenarios that were analyzed using finite element analysis included an axial tension load, an applied constant through-thickness-direction pressure load, and an axial compression load. Results for mechanics-based metrics of interest are presented and discussed for each loading scenario. Little sensitivity (less than one percent difference) to the effect of fiber-angle fidelity is observed in the mechanics-based metrics until the coarse-end of the considered range. Sensitivity to element size generally dominates the observed results for the mechanics-based metrics. Notable reductions in the preprocessing time are observed for increasingly coarse element size and fiber-rounding parameters. The preprocessing times decreased up to three orders of magnitude from a few thousand seconds to a few seconds without loss of accuracy in the mechanics-based metrics. Such increased computational performance is of particular interest to the structural design and analysis communities that may be conducting large counts of finite-element analyses, such as in other parametric studies, Monte-Carlo analyses, uncertainty quantification, or tow-steered optimization.

tow-steered composites↗
NASA NTRSDate not supplied

Analysis of Triangular Rollable and Collapsible Composite Booms Under the Effects of Gravity and Twist

Finite element analysis is used to investigate Triangular Rollable and Collapsible (TRAC) composite booms. The TRAC booms are subjected to a suite of loading conditions, including in-plane bending, out-of-plane bending, and axial compression. Simulations containing as-designed boom geometry are performed, as are simulations with geometric deviations associated with the as-built conditions of a sample TRAC boom. Namely, a cross-sectional twist along the length of the boom is incorporated into the analysis to study the effect of the twist on the deformation characteristics of the boom. Twisting in the sample boom was observed after short-term storage in a rolled configuration and may be attributed to differential creep deformation between the inner and outer flanges of the TRAC boom. Simulations are conducted with and without the effects of gravity to understand the significance of gravity on testing conditions. Booms of three lengths are evaluated: 3 meters, 7.5 meters and 30 meters. The mechanical responses of the TRAC booms are discussed with reference to the effects of gravity, boom length and cross-sectional twisting. Gravity is found to have a more significant effect on boom mechanical response as boom length is increased. Cross-sectional twisting is found to have a more significant effect on boom mechanical response in the shorter booms.

High-strain composites↗
NASA NTRSDate not supplied

Experimental Setup for Mechanically Testing Subscale Triangular, Rollable, and Collapsible Deployable Composite Booms

High-strain composite deployable space structures are used for space infrastructure and science applications such as solar array supports, antennae, camera masts, and lightweight structures supporting solar sailing propulsion ele-ments. Triangular, Rollable, and Collapsible (TRAC) deployable composite booms are one example of a high-strain composite deployable structure and were studied using novel experimental test and characterization methods developed under the Gravity Offloading and Analysis of Long Imperfection-sensitive Ele-ments (GOALIE) project. In the present work, a subscale 7-m-long TRAC boom was suspended vertically to orient gravity along the length of the boom. By ori-enting vertically, highly nonlinear and unstable behavior often encountered dur-ing horizontally oriented gravity offload testing of similar structures was reduced. Pretest analytical predictions of TRAC booms indicated three unique failure modes, loads, and locations for three unique loading cases of in-plane bending, out-of-plane bending, and axial compression. To investigate the predicted behav-ior, an experimental test was set up to impart mechanical loads to a subscale TRAC boom. The experimental setup, loading cases, and instrumentation used to characterize the mechanical response of a subscale TRAC boom are described in this paper.

High-strain composites↗