Search NASA⌕ Search

Engineering topics

Czarnecki, K. R.

Publications and source records attributed to Czarnecki, K. R..

29 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1961

Effects at Mach Numbers of 1.61 and 2.01 of Camber and Twist on the Aerodynamic Characteristics of Three Swept Wings Having the Same Planform

An investigation has been made at Mach numbers of 1.61 and 2.01 to determine the aerodynamic characteristics of three wings having a sweepback of 50 deg at the quarter-chord line, a taper ratio of 0.20, an NACA 65A005 thickness distribution, and an aspect ratio of 3.5. One wing was flat, one had at each spanwise station an a = 0 mean line modified to have a maximum height of 4-percent chord, and one had a linear variation of twist with 6 deg of washout at the tip. Tests were made with natural and fixed transition at Reynolds numbers ranging from 1.2 x 10(exp 6) to 3.6 x 10(exp 6) through an angle-of-attack range of -20 deg to 20 deg. When compared with the flat wing, the effect of the linear variation of twist with 6 deg of washout at the tip was to increase the lift-drag ratio when the leading edge was subsonic; but little increase in lift-drag ratio was obtained when the leading edge was supersonic. Pitching moment was increased and gave a positive trim point without greatly affecting the rate of change of pitching moment with lift coefficient. For the cambered wing the high minimum drag resulted in comparatively low lift-drag ratios. In addition, the pitching moments were decreased so that a negative trim point was obtained.

Landrum, Emma Jean↗
NASA NTRS1961

Boundary-Layer Transition on a Group of Blunt Nose Shapes at a Mach Number of 2.20

An investigation has been made to study boundary-layer transition on six axisymmetrical blunt bodies of revolution. Model shapes were selected with respect to the degree of favorable pressure gradient over the model surface. Tests were conducted at a Mach number of 2.20 and over a range of free-stream Reynolds number per foot of about 1.4 x 10(exp 6) to 6.5 x 10(exp 6). The tests were made at an angle of attack of 0 deg. with zero heat transfer. For the hemisphere, the flow remained essentially laminar over the model surface length for the entire pressure range of the tests. For a strong favorable pressure gradient followed by any weak favorable, neutral, or adverse gradient, the tendency was for transition to occur at or immediately behind the shoulder. A single strip of three-dimensional roughness in the region of strong favorable pressure gradient did not fix transition on the models at the roughness location except at the maximum test pressures, whereas a second roughness strip added in a region of neutral or adverse pressure gradient did fix transition. Experimental pressure coefficients agreed closely with modified Newtonian theory except in the shoulder region.

Jackson, Mary W.↗
NASA NTRS1961

Pressure Distributions and Wave Drag Due to Two-Dimensional Fabrication-Type Surface Roughness on an Ogive Cylinder at Mach Numbers of 1.61 and 2.01

An investigation has been made at Mach numbers of 1.61 and 2.01 and over a range of free-stream Reynolds number per foot from about 1.2 x 10(exp 6) to 8.3 x 10(exp 6) to determine the pressure distributions and wave drags due to two-dimensional fabrication-type surface roughness. Ten types of surface roughness, including step, wave, crease, and swept configurations were investigated. The tests were made on an ogive cylinder of fineness ratio 12.2, the roughness elements covering the cylindrical portion of the model. The results indicate that wave drag is the major component of the drag due to roughness at supersonic speeds. The pressure distributions over the roughness elements were generally found to be in good agreement with linearized two-dimensional theory except for regions of the elements affected by boundary-layer separation and shock detachment. There was little or no effect of Reynolds number except on the pressures within the regions influenced by separation or shock detachment. Inasmuch as most of the roughness configurations were affected by flow separation and shock detachment, there was generally an effect of Reynolds number on the roughness wave drag. This wave drag decreased as the free-stream Reynolds number was decreased.

Czarnecki, K. R.↗
NASA NTRS1961

Effect of Nose Bluntness on Transition for a Cone and a Hollow Cylinder at Mach Numbers 1.41 and 2.01

An investigation has been made to determine the effects of nose bluntness on boundary-layer transition for a cone with an included angle of 10 degrees and for a hollow cylinder. The tests were conducted at Mach numbers of 1.41 and 2.01 for free-stream Reynolds numbers per foot ranging from 1 x 10(exp 6) to 9 x 10(exp 6). The investigation was made with the use of schlieren photography for which the models were aligned with the free stream. For the 10 degree cone, the favorable effects of nose blunting were so small at both test Mach numbers as to be lost within the experimental accuracy. For small amounts of nose blunting on the hollow cylinder, for which the ratio of bluntness height to transition distance for the sharp-leading-edge cylinder was relatively small, there was little, if any, effect of blunting on transition. For somewhat larger values of this ratio, nose blunting had a favorable effect on transition. The magnitude of the favorable effect was dependent upon the size and the shape of the bluntness, and the maximum increase in transition distance relative to the sharp-leading-edge cylinder is in good agreement with the theoretical predictions of NACA Technical Report 1312. For relatively large values of the ratio of nose bluntness to transition distance, the effects of nose blunting were adverse for both the cone and the cylinder. In general, adverse effects due to blunting were larger for the flat bluntness than for the hemispherical or the round bluntness of equal bluntness height. Increasing the Mach number increased the size of bluntness required to induce adverse effects at constant free-stream Reynolds number per foot, delayed the adverse effects to higher values of Reynolds number per foot for constant nose bluntness, and reduced the abruptness of the transition decrease.

Monta, William J.↗
NASA NTRS1961

Effects of Cone Angle, Mach Number, and Nose Blunting on Transition at Supersonic Speeds

An investigation has been made to determine the transition characteristics of a group of blunt cones which varied in included apex angle from 27 deg to 60 deg over a Mach number range from 1.61 to 2.20 and a range of tunnel Reynolds number per foot from about 1.5 x 10(exp 6) to 8.0 x 10(exp 6). The tests were made at zero angle of attack and with zero heat transfer. The results indicate that the general level of transition Reynolds number based on boundary-layer momentum thickness and local flow conditions just outside the boundary layer varied between 600 and 1,100. Changes in Mach number had little effect on transition distance and transition Reynolds number for the near-sharp or very small bluntnesses. The effect of Mach number variation on the larger hemispherical bluntnesses was much stronger, with the strongest Mach number effect occurring for Mach numbers between 1.61 and 1.82. With an increase in nose radius, there was a strong decrease in transition distance and transition Reynolds number at the lower Mach numbers. This adverse effect tended to become weaker with increase in Mach number. An increase in cone angle at a constant Mach number caused a reduction in transition distance and transition Reynolds number for the blunt configurations which had approximately the same values of nose radius.

Czarnecki, K. R.↗
NASA NTRS1960

Investigation by Schlieren Technique of Methods of Fixing Fully Turbulent Flow on Models at Supersonic Speeds

An investigation has been made of the effectiveness of two-dimensional wire and three-dimensional grandular-type roughnesses for fixing transition on a 27 deg cone at a free-stream Mach number of 2.20. One height of each type of roughness was investigated over a free-stream Reynolds number per foot range of about 1.0 x 10 (exp 6) to 7.0 x 10 (exp 6). The tests were made at an angle of attack of 0 deg and with essentially zero heat transfer. The results indicate that, within the Reynolds number per foot range investigated, both two-dimensional wire and three-dimensional granular types of roughness caused large forward movements of transition at constant Reynolds number per foot; however, the forward movement with increase in Reynolds number per foot was very slow for the two-dimensional wire roughness and transition never reached the roughness location as it did with the three-dimensional granular roughness. An extrapolated value of the roughness Reynolds number (based on roughness height and flow conditions at the outer edge of the roughness) for the first appearance of forward movement from the smooth-cone case for the three-dimensional granular roughness was in good agreement with the value of about 600 for the first appearance of turbulent bursts obtained on a similar cone by the hot-wire technique. The range of values of roughness Reynolds number for which a fully turbulent boundary layer existed in the vicinity of the roughness element was about 4,500 to 6,500.

Jackson, Mary W.↗