Search NASA⌕ Search

Engineering topics

Dabo, Ismaila

Publications and source records attributed to Dabo, Ismaila.

At least 37 records · Page 2

Quantifying multipoint ordering in alloys

A central problem in multicomponent lattice systems is to systematically quantify multipoint ordering. Ordering in such systems is often described in terms of pairs, even though this is not sufficient when three-point and higher-order interactions are included in the Hamiltonian. Current models and parameters for multipoint ordering are often only applicable for very specific cases or require approximating a subset of correlated occupational variables on a lattice as being uncorrelated. In this paper, cluster order parameters are introduced to systematically quantify arbitrary multipoint ordering motifs in substitutional systems through direct calculations of normalized cluster probabilities. These parameters can describe multipoint chemical ordering in crystal systems with multiple sublattices, multiple components, and systems with reduced symmetry. These are defined in this paper and applied to quantify four-point chemical ordering motifs in platinum/palladium alloy nanoparticles that are of practical interest to the synthesis of catalytic nanocages. Impacts of chemical ordering on nanocage stability are discussed. It is demonstrated that approximating four-point probabilities from superpositions of lower-order pair probabilities is not sufficient in cases where three- and four-body terms are included in the energy expression. Furthermore, conclusions about the formation mechanisms of nanocages may change significantly when using common pair approximations.

36 MATERIALS SCIENCE↗

Single-Step Direct Laser Writing of Multimetal Oxygen Evolution Catalysts from Liquid Precursors

We investigate a laser direct-write method to synthesize and deposit metastable, mixed transition metal oxides and evaluate their performance as oxygen evolution reaction catalysts. This laser processing method enabled the rapid synthesis of diverse heterogeneous alloy and oxide catalysts directly from cost-effective solution precursors, including catalysts with a high density of nanocrystalline metal alloy inclusions within an amorphous oxide matrix. The nanoscale heterogenous structures of the synthesized catalysts were consistent with reactive force-field Monte Carlo calculations. By evaluating the impact of varying transition metal oxide composition ratios, we created a stable Fe 0.63 Co 0.19 Ni 0.18 O x /C catalyst with a Tafel slope of 38.23 mV dec -1 and overpotential of 247 mV, a performance similar to that of IrO 2 . Synthesized Fe 0.63 Co 0.19 Ni 0.18 O x /C and Fe 0.14 Co 0.46 Ni 0.40 O x /C catalysts were experimentally compared in terms of catalytic performance and structural characteristics to determine that higher iron content and a less crystalline structure in the secondary matrix decreases the charge transfer resistance and thus is beneficial for electrocatalytic activity. Furthermore, this conclusion is supported by density-functional theory calculations showing distorted active sites in ternary metal catalysts are key for lowering overpotentials for the oxygen evolution reaction.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Ferroelectricity in boron-substituted aluminum nitride thin films

This manuscript demonstrates ferroelectricity in B-substituted AlN thin films and a complementary set of first-principles calculations to understand their structure-property relationships. Al 1–x B x N films are grown by dual-cathode reactive magnetron sputtering on (110)W/(001)Al 2 O 3 substrates at 300°C at compositions spanning x = 0 to x = 0.20. X-ray diffraction studies indicate a decrease in both the c and a lattice parameters with increasing B concentration, resulting in a decrease in unit cell volume and a constant c/a axial ratio of 1.60 over this composition range. Films with 0.02 ≤ x ≤ 0.15 display ferroelectric switching with remanent polarizations exceeding 125 μCcm –2 while maintaining band gap energies of > 5.2eV. The large band gap allows low frequency hysteresis measurement (200 Hz) with modest leakage contributions. At B concentrations of x > 0.15, c-axis orientation deteriorates and ferroelectric behavior is degraded. Furthermore, density-functional theory calculations corroborate the structural observations and provide predictions for the wurtzite u parameter, polarization reversal magnitudes, and composition-dependent coercive fields.

36 MATERIALS SCIENCE↗

Predicting the Pseudocapacitive Windows for MXene Electrodes with Voltage-Dependent Cluster Expansion Models

MXene transition-metal carbides and nitrides are of growing interest for energy storage applications. These compounds are especially promising for use as pseudocapacitive electrodes due to their ability to convert energy electrochemically at fast rates. Using voltage-dependent cluster expansion models, we predict the charge storage performance of MXene pseudocapacitors for a range of electrode compositions. M 3 C 2 O 2 electrodes based on group-VI transition metals have up to 80% larger areal energy densities than prototypical titanium-based (e.g., Ti 3 C 2 O 2 ) MXene electrodes. We attribute this high pseudocapacitance to the Faradaic voltage windows of group-VI MXene electrodes, which are predicted to be 1.2 to 1.8 times larger than those of titanium-based MXenes. The size of the pseudocapacitive voltage window increases with the range of oxidation states that are accessible to the MXene transition metals. Here, by similar mechanisms, the presence of multiple ions in the solvent (Li + and H + ) leads to sharp changes in the transition-metal oxidation states and can significantly increase the charge capacity of MXene pseudocapacitors.

36 MATERIALS SCIENCE↗

First Principles Simulations of Electrified Interfaces in Electrochemistry

This chapter discusses some of the recent advances made in the first principles modeling of electrochemical catalysts. It also discusses the key development, namely the ability to explicitly treat the effects of surface electrification due to electrochemical processes and applied voltages in a computationally efficient manner. The chapter introduces the thermodynamics and statistical mechanics of electrified metal-solution interfaces. It then discusses the structure of the electrode-electrolyte interface and the effects of applied voltages, followed by an overview of the first-principles model and a motivating example. The chapter also provides a brief summary of classical thermodynamics and describes the basics of thermodynamic detour. It considers the thermodynamics of macroscopic systems and introduces several useful fundamental relations. Here, the chapter also considers a system to exist in a certain macrostate, which is a particular thermodynamic state specified by a set of fixed properties such as constant particle number, constant volume, and constant temperature.

36 MATERIALS SCIENCE↗

First-principles study and experimental characterization of metal incorporation in germanium telluride

Germanium telluride is a well-known phase change material (PCM) used in non-volatile memory cells and radio frequency switches. Controlling the properties of GeTe for improved PCM device performance has sometimes been achieved by doping and/or alloying with metals, often at concentrations greater than 10 at. % and using non-equilibrium methods. Here, since switching PCMs between the low-resistance crystalline and high-resistance amorphous states requires a heating cycle, the stability of metal-incorporated GeTe (Ge 0.5–x M x Te 0.5 ) films is also critical to practical implementation of these materials in electronic and optoelectronic devices. In this work, we use both density-functional theory and experimental characterization methods to probe the solubility and critical properties of Ge 0.5–x M x Te 0.5 films. Using first-principles calculations, we determine the enthalpy of formation for GeTe with 2.08, 4.17, and 6.25 at. % of Cu, Fe, Mn, Mo, and Ti and show trends between the stability of the Ge 0.5–x M x Te 0.5 systems and the atomic position, composition, and distribution of the metal atoms in the GeTe matrix.

36 MATERIALS SCIENCE↗

Photophysics and Electronic Structure of Lateral Graphene/MoS 2 and Metal/MoS 2 Junctions

Integration of semiconducting transition metal dichalcogenides (TMDs) into functional optoelectronic circuitries requires an understanding of the charge transfer across the interface between the TMD and the contacting material. In this work, we use spatially resolved photocurrent microscopy to demonstrate electronic uniformity at the epitaxial graphene/molybdenum disulfide (EG/MoS 2 ) interface. A 10× larger photocurrent is extracted at the EG/MoS 2 interface when compared to the metal (Ti/Au)/MoS 2 interface. This is supported by semi-local density functional theory (DFT), which predicts the Schottky barrier at the EG/MoS 2 interface to be ~2× lower than that at Ti/MoS 2 . We provide a direct visualization of a 2D material Schottky barrier through combination of angle-resolved photoemission spectroscopy with spatial resolution selected to be ~300 nm (nano-ARPES) and DFT calculations. A bending of ~500 meV over a length scale of ~2-3 μm in the valence band maximum of MoS 2 is observed via nano-ARPES. We explicate a correlation between experimental demonstration and theoretical predictions of barriers at graphene/TMD interfaces. Spatially resolved photocurrent mapping allows for directly visualizing the uniformity of built-in electric fields at heterostructure interfaces, providing a guide for microscopic engineering of charge transport across heterointerfaces. This simple probe-based technique also speaks directly to the 2D synthesis community to elucidate electronic uniformity at domain boundaries alongside morphological uniformity over large areas.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Optimized utilization of COMB3 reactive potentials in LAMMPS

An investigation to optimize the application of the third-generation charge optimized many-body (COMB3) interatomic potential and associated input parameters was carried out through the study of solid–liquid interactions in classical molecular dynamics simulations. The rates of these molecular interactions are understood through the wetting rates of water nano-droplets on a bare copper (111) surface. Implementing the Langevin thermostat, the influence of simulation time step, the number of atoms in the system, the frequency at which charge equilibration is performed, and the temperature relaxation rate are all examined. The results indicate that time steps of 0.4 fs are possible when using longer relaxation times for the system temperature, which is almost double the typical time step used for reactive potentials. Additionally, the use of the charge equilibration allows for a fewer atomic layers to be used in the Cu slab. In addition, charge equilibrium schemes do not need to be performed every time step to ensure accurate charge transfer. Interestingly, the rate of wetting for the nanodroplets is dominantly dependent on the temperature relaxation time, which is predicted to significantly change the viscosity of the water droplets. This work provides a pathway for optimizing simulations using the COMB3 reactive interatomic potential.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effects of surface charge and cluster size on the electrochemical dissolution of platinum nanoparticles using COMB3 and continuum electrolyte models

We study the site-dependent dissolution of platinum nanoparticles under electrochemical conditions to assess their thermodynamic stability as a function of shape and size using empirical molecular dynamics and electronic-structure models. The third-generation charge optimized many-body potential is employed to determine the validity of uniform spherical representations of the nanoparticles in predicting dissolution potentials (the Kelvin model). To understand the early stages of catalyst dissolution, implicit solvation techniques based on the self-consistent continuum solvation method are applied. It is demonstrated that interfacial charge and polarization can shift the dissolution energies by amounts on the order of 0.74 eV depending on the surface site and nanoparticle shape, leading to the unexpected preferential removal of platinum cations from highly coordinated sites in some cases.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Vibrational probe of the origin of singlet exciton fission in TIPS-pentacene solutions

We use native vibrational modes of the model singlet fission chromophore 6,13-bis(triisopropylsilylethynyl)pentacene (TIPS-Pn) to examine the origins of singlet fission in solution between molecules that are not tethered by a covalent linkage. We use the C—H stretch modes of TIPS side groups of TIPS-Pn to demonstrate that singlet fission does not occur by diffusive encounter of independent molecules in solution. Instead, TIPS-Pn molecules aggregate in solution through their TIPS side groups. This aggregation breaks the symmetry of the TIPS-Pn molecules and enables the formation of triplets to be probed through the formally symmetry forbidden symmetric alkyne stretch mode of the TIPS side groups. The alkyne stretch modes of TIPS-Pn are sensitive to the electronic excited states present during the singlet fission reaction and provide unique signatures of the formation of triplets following the initial separation of triplet pair intermediates. These findings highlight the opportunity to leverage structural information from vibrational modes to better understand intermolecular interactions that lead to singlet fission.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Understanding the influence of defects and surface chemistry on ferroelectric switching: a ReaxFF investigation of BaTiO 3

Ferroelectric materials such as barium titanate (BaTiO 3 ) have a wide range of applications in nano scale electronic devices due to their outstanding properties. In this study, we developed an easily extendable atomistic ReaxFF reactive force field for BaTiO 3 that can capture both its field- and temperature-induced ferroelectric hysteresis and corresponding changes due to surface chemistry and bulk defects. Using our force field, we were able to reproduce and explain a number of experimental observations: (1) the existence of a critical thickness of 4.8 nm below which ferroelectricity vanishes in BaTiO 3 ; (2) migration and clustering of oxygen vacancies (OVs) in BaTiO 3 and a reduction in the polarization and the Curie temperature due to the OVs; (3) domain wall interaction with the surface chemistry to influence the ferroelectric switching and polarization magnitude. This new computational tool opens up a wide range of possibilities for making predictions for realistic ferroelectric interfaces in energy-conversion, electronic and neuromorphic systems.

36 MATERIALS SCIENCE↗

BaZrSe 3 : Ab initio study of anion substitution for bandgap tuning in a chalcogenide material

Recently, transition metal perovskite chalcogenide materials have been introduced as possible candidates for solar cell applications. Here, we provide accurate theoretical calculations for BaZrS 3 and two phases of SrZrS 3 , which have been recently synthesized and their optical properties elaborated. In this study, we consider the substitution of S in BaZrS 3 with Se to form BaZrSe 3 . Evolutionary methods are used to find the optimal structure of this compound, and accurate calculations of its optoelectronic properties are presented. Using phonon frequency calculations and ab initio molecular dynamics, we assess the stability of this compound. We find that BaZrSe 3 is likely to be stable under typical conditions, with a low bandgap and high optical absorption coefficients. This indicates that BaZrSe 3 could be useful for solar cell applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

New frontiers for the materials genome initiative

The Materials Genome Initiative (MGI) advanced a new paradigm for materials discovery and design, namely that the pace of new materials deployment could be accelerated through complementary efforts in theory, computation, and experiment. Along with numerous successes, new challenges are inviting researchers to refocus the efforts and approaches that were originally inspired by the MGI. In May 2017, the National Science Foundation sponsored the workshop “Advancing and Accelerating Materials Innovation Through the Synergistic Interaction among Computation, Experiment, and Theory: Opening New Frontiers” to review accomplishments that emerged from investments in science and infrastructure under the MGI, identify scientific opportunities in this new environment, examine how to effectively utilize new materials innovation infrastructure, and discuss challenges in achieving accelerated materials research through the seamless integration of experiment, computation, and theory. This article summarizes key findings from the workshop and provides perspectives that aim to guide the direction of future materials research and its translation into societal impacts.

36 MATERIALS SCIENCE↗

Voltage effects on the stability of Pd ensembles in Pd–Au/Au(111) surface alloys

The catalytic performance of multimetallic electrodes is often attributed to a beneficial combination of ligand, strain, and ensemble effects. Understanding the influence of the electrochemical environment on the stability of the alloy surface structure is thus a crucial component to the design of highly active and durable electrocatalysts. In this work, we study the effects of an applied voltage to electrocatalytic Pd–Au/Au(111) surface alloys in contact with a model continuum electrolyte. Using planewave density functional theory, two-dimensional cluster expansions are parameterized and used to simulate dilute Pd–Au surface alloys under electrochemical conditions via Metropolis Monte Carlo within an extended canonical ensemble. While Pd monomers are stable at all potentials considered, different extents of surface electrification are observed to promote the formation of Pd dimers and trimers, as well as clusters of Pd monomers. We find that the relative proportion of monomer, dimer, and trimer surface fractions is in good agreement with in situ scanning tunneling microscopy measurements. The further development and refinement of the approaches described herein may serve as a useful aid in the development of next-generation electrocatalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Conjugated Block Copolymers as Model Systems to Examine Mechanisms of Charge Generation in Donor–Acceptor Materials

Abstract Fully conjugated donor–acceptor block copolymers are established as model systems to elucidate fundamental mechanisms of photocurrent generation in organic photovoltaics. Using analysis of steady‐state photoluminescence quenching, exciton dissociation to a charge transfer state within individual block copolymer chains is quantified. By making a small adjustment to the conjugated backbone, the electronic properties are altered enough to disrupt charge transfer almost entirely. Strong intermolecular coupling of the electron donor is introduced by synthesizing block copolymer nanoparticles. Transient absorption spectroscopy is used to monitor charge generation in block copolymer isolated chains and nanoparticles. While efficient charge transfer is observed in isolated chains, there is no indication of complete charge separation. In the nanoparticles, long‐lived polarons are observed as early as ≈15 ns. Thus, aggregation of electron donors can facilitate efficient charge generation.

Aplan, Melissa P.↗