Search NASA⌕ Search

Engineering topics

Dahl, M. D.

Publications and source records attributed to Dahl, M. D..

9 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2005

Noise and Spreading of a Subsonic Coannular Jet - Comparison with Single Equivalent Jet

The issue of scaling of noise as well as spreading of subsonic coannular jets is revisited. Far-field noise and centerline Pitot-static pressure surveys are conducted with concentric, circular nozzles having an outer-to-inner diameter ratio of 1.42. Both the inner nozzle and the outer annular passage are convergent. Outer-to-inner Mach number ratio (R) is varied over a large range from 0 to approximately 10. Results are examined on the basis of single equivalent jet parameters calculated by satisfying continuity, momentum and energy equations. The results confirm that coannular jets with normal velocity profiles are noisier than the single equivalent jet. Jets with "inverted" velocity profiles are also found to be noisier except in a narrow R-range of 1-1.5. In the latter range, contrasting the inference in previous studies of IVP jets, the present data do not exhibit a clear noise reduction. When normalized with equivalent jet parameters the asymptotic Mach number decay rate, as well as potential core length, are found to be comparable to those of a single jet. However, an abrupt shift in the virtual origin is noted across R=1.

Zaman, K. B. M. Q.↗
NASA NTRS2003

Sound Radiated by a Wave-Like Structure in a Compressible Jet

This paper extends the analysis of acoustic radiation from the source model representing spatially-growing instability waves in a round jet at high speeds. Compared to previous work, a modified approach to the sound source modeling is examined that employs a set of solutions to linearized Euler equations. The sound radiation is then calculated using an integral surface method.

Golubev, V. V.↗
NASA NTRS2001

Experimental Investigation of 'Transonic Resonance' with Convergent-Divergent Nozzles

Convergent-divergent nozzles, when run at pressure ratios lower than the design value, often undergo a flow resonance accompanied by the emission of acoustic tones. The phenomenon, different in characteristics from conventional 'screech' tones, has been studied experimentally. Unlike screech, the frequency increases with increasing supply pressure. There is a 'staging' behavior; 'odd harmonic' stages resonate at lower pressures while the fundamental occurs in a range of higher pressures corresponding to a fully expanded Mach number (M(sub j)) around unity. The frequency (f(sub N)) variation with M(sub j) depends on the half angle-of-divergence (theta) of the nozzle. At smaller theta, the slope of f(sub N) versus M(sub j) curve becomes steeper. The resonance involves standing waves and is driven by unsteady shock/boundary layer interaction. The distance between the foot of the shock and the nozzle exit imposes the lengthscale (L'). The fundamental corresponds to a quarterwave resonance, the next stage at a lower supply pressure corresponds to a three-quarter-wave resonance, and so on. The principal trends in the frequency variation are explained simply from the characteristic variation of the length-scale L'. Based on the data, correlation equations are provided for the prediction of f(sub N). A striking feature is that tripping of the boundary layer near the nozzle's throat tends to suppress the resonance. In a practical nozzle a tendency for the occurrence of the phenomenon is thought to be a source of 'internal noise'; thus, there is a potential for noise benefit simply by appropriate boundary layer tripping near the nozzle's throat.

Zaman, K. B. M. Q.↗
NASA NTRS1999

Aeroacoustic Resonance with Convergent-Divergent Nozzles

Convergent-divergent nozzles, when run at off-design conditions, often undergo flow resonance accompanied by the emission of a tone. Apart from screech occurring at higher operating pressures, resonance is also common at lower Mach numbers near transonic as well as subsonic conditions. With data from six nozzles of different size and design Mach number, the present paper documents the characteristics of the latter phenomenon that is morphologically quite different from conventional screech. The resonance is due to a feedback loop internal to the nozzle and is apparently driven by unsteady laminar boundary layer separation near the throat of the nozzle. Appropriate boundary layer tripping prior to the throat is found to eliminate or alter most of the tones. The Helmholtz number of the resonance, based on the throat-to-exit length, is found to attain a value of approximately 0.15 at M(sub j)=1 for all nozzles. However, its variation with M(sub j) may be different and depend on the nozzle geometry. With nozzles having larger throat-to-exit angle of divergence, the frequency is found to increase, in some cases having stage jumps to lower frequencies, with increasing operating pressure. With nozzles having smaller angle of divergence, the frequency variation exhibits an increase followed by a decrease involving one prominent stage occurring around transonic (M(sub j)= 1) condition. While the mechanisms remain far from completely clear, a model involving downstream propagating aerodynamic disturbance together with acoustic feedback explains the overall frequency characteristics for most cases.

Zaman, K. B. M. Q.↗
NASA NTRS1997

Noise from Supersonic Coaxial Jets: Normal Velocity Profile - Part 2

Instability waves have been established as noise generators in supersonic jets. Recent analysis of these slowly diverging jets has shown that these instability waves radiate noise to the far field when the waves have components with phase velocities that are supersonic relative to the ambient speed of sound. This instability wave noise generation model has been applied to supersonic jets with a single shear layer and is now applied to supersonic coaxial jets with two initial shear layers. In this paper the case of coaxial jets with normal velocity profiles is considered, where the inner jet stream velocity is higher than the outer jet stream velocity. To provide mean flow profiles at all axial locations, a numerical scheme is used to calculate the mean flow properties. Calculations are made for the stability characteristics in the coaxial jet shear layers and the noise radiated from the instability waves for different operating conditions with the same total thrust, mass flow and exit area as a single reference jet. The effects of changes in the velocity ratio, the density ratio and the area ratio are each considered independently.

Dahl, M. D.↗
NASA NTRS1990

Some observations on transitory stall in conical diffusers

Results from an experimental investigation on the flow through conical diffusers are presented. The mean and fluctuating velocity fields are compared for three diffusers with total diffusion angles of 16, 20 and 24 degrees, in the throat Mach number (M sub t) range of 0.05 to 0.95. Each of the diffusers were 14 cm long and had a 5.08 cm inlet diameter, and the flow exited into the ambient. The boundary layer at the throat was thin with the throat diameter (D sub t) to momentum thickness (O) ratio being as high as 800 at M(sub t) = 0.4. While the 16 deg diffuser flow exited with a top-hat mean velocity profile, increasing losses due to increasing separation resulted in fuller profiles for the 20 and 24 degrees cases. A detailed flow field study was conducted for the 16 deg diffuser. The u'-spectrum, measured at the exit plane, exhibited a peak apparently due to the ensuing jet column instability throughout the M(sub t) range covered. In addition, a much lower frequency spectral peak also occurred in the M(sub t) range of 0.3 to 0.7. Both of the spectral peaks were due to axisymmetric flow fluctuations. A self-sustaining flow oscillation occurred in the M(sub t) range of 0.6 to 0.85, emitting a loud tone, when the jet column instability frequency matched the resonance frequency of the diffuser. Limited data showed that artificial acoustic excitation was effective in reducing the flow fluctuations, with a resultant increase in the pressure recovery, at low M(sub t).

Zaman, K. B. M. Q.↗
NASA NTRS1989

Some Observations on Transitory Stall in Conical Diffusers

Results from an experimental investigation on the flow through conical diffusers are presented. The mean and fluctuating velocity fields are compared for three diffusers with total diffusion angles of 16, 20 and 24 degrees, in the throat Mach number (M sub t) range of 0.05 to 0.95. Each of the diffusers were 14 cm long and had a 5.08 cm inlet diameter, and the flow exited into the ambient. The boundary layer at the throat was thin with the throat diameter (D sub t) to momentum thickness (O) ratio being as high as 800 at M(sub t) = 0.4. While the 16 deg diffuser flow exited with a top-hat mean velocity profile, increasing losses due to increasing separation resulted in fuller profiles for the 20 and 24 degree cases. A detailed flow field study was conducted for the 16 deg. diffuser. The u'-spectrum, measured at the exit plane, exhibited a peak apparently due to the ensuing jet column instability throughout the M(sub t) range covered. In addition, a much lower frequency spectral peak also occurred in the M(sub t) range of 0.3 to 0.7. Both of the spectral peaks were due to axisymmetric flow fluctuations. A self-sustaining flow oscillation occurred in the M(sub t) range of 0.6 to 0.85, emitting a loud tone, when the jet column instability frequency matched the resonance frequency of the diffuser. Limited data showed that artificial acoustic excitation was effective in reducing the flow fluctuations, with a resultant increase in the pressure recovery, at low M(sub t).

Zaman, K. B. M. Q.↗
NASA NTRS1985

Measured acoustic properties of variable and low density bulk absorbers

Experimental data were taken to determine the acoustic absorbing properties of uniform low density and layered variable density samples using a bulk absober with a perforated plate facing to hold the material in place. In the layered variable density case, the bulk absorber was packed such that the lowest density layer began at the surface of the sample and progressed to higher density layers deeper inside. The samples were placed in a rectangular duct and measurements were taken using the two microphone method. The data were used to calculate specific acoustic impedances and normal incidence absorption coefficients. Results showed that for uniform density samples the absorption coefficient at low frequencies decreased with increasing density and resonances occurred in the absorption coefficient curve at lower densities. These results were confirmed by a model for uniform density bulk absorbers. Results from layered variable density samples showed that low frequency absorption was the highest when the lowest density possible was packed in the first layer near the exposed surface. The layers of increasing density within the sample had the effect of damping the resonances.

Dahl, M. D.↗