Search NASA⌕ Search

Engineering topics

Daly, E.

Publications and source records attributed to Daly, E..

32 records · Page 2

Improvements for LCLS-II Cryomodule Transportation

The Linear Coherent Light Source (LCLS-II) is currently being constructed at the SLAC National Laboratory. A total of 35 cryomodules will be fabricated at Jefferson Lab (JLab) in Virginia and Fermi National Laboratory (FNAL) in Illinois and transported via road to SLAC. A shipping frame with an inner bed isolated by springs was designed to protect the CMs from shocks and vibrations during shipments. Successful road testing of the JLab prototype paved the way for production CM shipments. The initial production shipments lead to several catastrophic failures in beamline vacuum in the cryomodules. The failures were determined to be due to fatigue in Fundamental Power Coupler (FPC) bellows due to excessive motion during shipment. A series of instrumented CM shipping tests and component tests were undertaken to develop a solution. A modified spring layout was tested and implemented, which reduced shocks on the CMs. FPC coupler bellows restraints were tested on a shaker table and on a CM during shipping; they were able to reduce bellows motion by a factor of three. The updated shipping system is currently in use and has successfully delivered six cryomodules to SLAC from JLab and FNAL.

Huque, N. A.↗

Commissioning the JLab LERF Cryomodule Test Facility

The JLab Low Energy Recirculating Facility, LERF, has been modified to support concurrent testing of two LCLS-II cryomodules. The cryomodules are installed in a similar fashion as they would be in the L1 section of the LCLS-II linac, including the floor slope and using all of the LCLS-II hardware and controls for cryomodule cryogenics, vacuum, and RF (SSA and LLRF). From the start, it was intended to use LCLS-II electronics and EPICS software controls for cryomodule testing. In affect the LERF test facility becomes the first opportunity to commission and operate the LCLS-II LINAC hardware and software controls. Support for specific cryomodule high level test applications like Q0 and HOMs measurements, are being developed from the basic cryomodule control suite. To support the testing, 2 K He is supplied from the CEBAF south linac cryogenic system, where care must be taken when using the LERF test facility to not upset the CEBAF cryogenics plant. This paper discusses the commissioning of the hardware and software development for testing the first two LCLS-II cryomodules.

Hovater, C.↗

Current Results from Acceptance Testing of LCLS-II Cryomodules at Jefferson Lab

The Thomas Jefferson National Accelerator Facility is currently engaged, along with several other Department of Energy (DOE) national laboratories, in the Linac Co-herent Light Source II project (LCLS-II). The SRF Insti-tute at Jefferson Lab is currently building 21 cryomod-ules for this project. The cryomodules are based on the XFEL design and have been modified for continuous wave (CW) operation and to comply with other LCLS-II specifications. Each cryomodule contains eight 9-cell cavities with coaxial power couplers operating at 1.3 GHz. The cryomodule also contain a magnet package that consists of a quadrupole and two correctors. Most of these cryomodules will be tested in the Cryomodule Test Facility (CMTF) at Jefferson Lab before shipment to SLAC. Up to three of these cryomodules will be tested in a test stand set up in the Low Energy Recovery Facility (LERF) at Jefferson Lab. Acceptance testing of the LCLS-II cryomodules began in December 2016. Twelve cryomodules have currently completed Acceptance Test-ing. This paper will summarize the results of those tests.

Drury, M.↗

Transport of LCLS-II 1.3 Ghz cryomodule to SLAC

In a partnership with SLAC National Accelerator Laboratory (SLAC) and Jefferson Lab, Fermilab will assemble and test 17 of the 35 total 1.3 GHz cryomodules for the Linac Coherent Light Source II (LCLS-II) Project. These include a prototype built and delivered by each Lab. Another two 3.9 GHz cryomodules will be built, tested and transported by Fermilab to SLAC. Each assembly will be transported over-the-road from Fermilab or Jefferson Lab using specific routes to SLAC. The transport system consists of a base frame, isolation fixture and upper protective truss. The strongback cryomodule lifting fixture is described along with other supporting equipment used for both over-the-road transport and local (on-site) transport at Fermilab. Initially, analysis of fragile components and stability studies will be performed in order to assess the risk associated with over-the-road transport of a fully assembled cryomodule.

43 PARTICLE ACCELERATORS↗

Progress on the design of the polarized Medium-energy Electron Ion Collider at JLAB

The Medium-energy Electron Ion Collider (MEIC) at JLab is designed to provide high luminosity and high polarization needed to reach new frontiers in the exploration of nuclear structure. The luminosity, exceeding 10 33 cm -2 s -1 in a broad range of the center-of-mass (CM) energy and maximum luminosity above 10 34 cm -2 s -1 , is achieved by high-rate collisions of short small-emittance low-charge bunches made possible by high-energy electron cooling of the ion beam and synchrotron radiation damping of the electron beam. The polarization of light ion species (p, d, 3 He) can be easily preserved and manipulated due to the unique figure-8 shape of the collider rings. A fully consistent set of parameters have been developed considering the balance of machine performance, required technical development and cost. This paper reports recent progress on the MEIC accelerator design including electron and ion complexes, integrated interaction region design, figure-8-ring-based electron and ion polarization schemes, RF/SRF systems and ERL-based high-energy electron cooling. Luminosity performance is also presented for the MEIC baseline design.

43 PARTICLE ACCELERATORS↗

PROGRESS ON THE DESIGN OF THE POLARIZED MEDIUM-ENERGY ELECTRON ION COLLIDER AT JLAB

The Medium-energy Electron Ion Collider (MEIC) at JLab is designed to provide high luminosity and high polarization needed to reach new frontiers in the exploration of nuclear structure. The luminosity, exceeding 1033 cm-2s-1 in a broad range of the center-of-mass (CM) energy and maximum luminosity above 1034 cm-2s-1, is achieved by high-rate collisions of short small-emittance low-charge bunches made possible by high-energy electron cooling of the ion beam and synchrotron radiation damping of the electron beam. The polarization of light ion species (p, d, 3He) can be easily preserved and manipulated due to the unique figure-8 shape of the collider rings. A fully consistent set of parameters have been developed considering the balance of machine performance, required technical development and cost. This paper reports recent progress on the MEIC accelerator design including electron and ion complexes, integrated interaction region design, figure-8-ring-based electron and ion polarization schemes, RF/SRF systems and ERL-based high-energy electron cooling. Luminosity performance is also presented for the MEIC baseline design.

Lin, F.↗

Design Analysis and Manufacturing Studies for ITER In-Vessel Coils

ITER is incorporating two types of In Vessel Coils (IVCs): ELM Coils to mitigate Edge Localized Modes and VS Coils to provide Vertical Stabilization of the plasma. Strong coupling with the plasma is required so that the ELM and VS Coils can meet their performance requirements. Accordingly, the IVCs are in close proximity to the plasma, mounted just behind the Blanket Shield Modules. This location results in a radiation and temperature environment that is severe necessitating new solutions for material selection as well as challenging analysis and design solutions. Fitting the coil systems in between the blanket shield modules and the vacuum vessel leads to difficult integration with diagnostic cabling and cooling water manifolds.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

3D vacuum magnetic field modelling of the ITER ELM control coil during standard operating scenarios

In-vessel, non-axisymmetric, control coils have proven to be an important option for mitigating and suppressing edge-localized modes (ELMs) in high performance operating regimes on a growing number of tokamaks. Additionally, an in-vessel non-axisymmetric ELM control coil is being considered in the ITER baseline design. For this paper, in preparing for the initial operation of this coil set, a comprehensive study was carried out to characterize the linear superposition of the 3D vacuum magnetic field, produced by the ELM coil, on a series of equilibria representing nine standard ITER operating scenarios. Here, the spatial phase angle of toroidally distributed currents, specified with a cosine waveform, in the upper and lower rows of the ITER ELM coil (IEC) set is varied in 2° steps while holding the current in the equatorial row of coils constant. The peak current in each of the three toroidal rows of window-frame coils making up the IEC is scanned between 5 kAt and 90 kAt in 5 kAt steps and the width of the edge region covered by overlapping vacuum field magnetic islands is calculated. This width is compared to a vacuum field ELM suppression correlation criterion found in DIII-D. A minimum coil current satisfying the DIII-D criterion, along with an associated set of phase angles, is identified for each ITER operating scenario. These currents range from 20 kAt to 75 kAt depending on the operating scenario being used and the toroidal mode number (n) of the cosine waveform. Comparisons between the scaling of the divertor footprint area in cases with n = 3 perturbation fields versus those with n = 4 show significant advantages when using n = 3. In addition, it is found that the DIII-D correlation criterion can be satisfied in the event that various combinations of individual IEC window-frame coils need to be turned off due to malfunctioning components located inside the vacuum vessel. Finally, details of these results for both the full set of 27 window-frame coils and various reduced sets, using either n = 3 and n = 4 perturbation fields, are discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The high-energy proton fluxes in the SAA observed with REM aboard the MIR orbital station

During two years, from November 1994 to 1996, the particle detector REM measured the highly energetic electron and proton environment at the outside of the MIR orbital station. Using mission averaged data we investigate various aspects of the proton fluxes in the SAA. Comparison with the radiation belt model AP8 reveal important differences. c2002 Elsevier Science Ltd. All rights reserved.

long duration↗