Engineering topics

Dameron, Arrelaine A.

Publications and source records attributed to Dameron, Arrelaine A..

4 records

DOE OSTI2024

How Low Can You Go? Nanoscale Membranes for Efficient Water Electrolysis

Motivated by the need to lower the cost of hydrogen (H 2 ) production by water electrolysis, significant research efforts are focused on making proton (H + ) exchange membrane (PEM) water electrolyzers more efficient and capable of operating at higher current densities. These aims can be met by making H + -conducting membranes thinner, which has the effect of lowering ohmic drops across the membrane that represent the largest efficiency loss at high current densities (>2 A cm –2 ). However, decreasing membrane thickness below 50 μm is not trivial due to trade-offs between membrane resistance, H 2 crossover (safety), membrane degradation, and manufacturing throughput. Furthermore, descriptions of key processes, limitations, and trade-offs that arise in thin membranes are provided that can be used to guide the design of ultrathin (i.e., submicron thick), low-resistance membrane materials that have the potential to transform the field of clean H 2 production.

08 HYDROGEN↗

DOE OSTI2023

Towards improved conversion of wet waste to jet fuel with atomic layer deposition-coated hydrodeoxygenation catalysts

The conversion of wet waste-derived volatile fatty acids into jet fuel-range hydrocarbons is a promising route for increasing the production of sustainable aviation fuel; however, the cost and moderate alkane selectivity of Pt-based hydrodeoxygenation catalysts present challenges for commercialization. Here, to address this, we used atomic layer deposition to apply TiO 2 overcoats to Pt/Al 2 O 3 catalysts and create new interface sites that exhibited 8 times higher site time yield of the desirable n-alkane product than uncoated catalyst. Through TPR/TPD, XPS, CO DRIFTS, and DFT calculations, we found that the increased selectivity of the ALD-coated catalyst was due to the creation of O vacancies at the Pt-TiO 2 interface under reducing conditions, resulting in new Ti 3+ acid sites near the active metal. Maximum conversion and alkane selectivity during HDO was achieved with an ALD-coated 0.5% wt Pt catalyst, indicating that TiO 2 ALD can be used to maximize the utility of precious-metal catalysts.

09 BIOMASS FUELS↗

DOE OSTI2021

Atomic Layer Deposition with TiO2 for Enhanced Reactivity and Stability of Aromatic Hydrogenation Catalysts

Hydrogenation of aromatic molecules in fossil- and bio-derived fuels is essential for decreasing emissions of harmful combustion products and addressing growing concerns around urban air pollution. In this work, we used atomic layer deposition to significantly enhance the hydrogenation performance of a conventional supported Pd catalyst by applying an ultrathin coating of TiO2 in a scalable powder coating process. The TiO2-coated catalyst showed substantial gains in the conversion of multiple aromatic molecules, including a 5-fold improvement in turnover frequency versus the uncoated catalyst in the hydrogenation of naphthalene. This activity enhancement was maintained upon scaling the coating synthesis process from 3 to 100 g. Based on the results from Xray photoelectron spectroscopy, X-ray absorption spectroscopy, and computational modeling, the activity enhancement was attributed to ensemble effects resulting from partial TiO2 coverage of the Pd surface rather than fundamental changes to the Pd electronic structure. Additional durability testing confirmed that the TiO2 coating improved the thermal and hydrothermal stability of the catalyst as well as tolerance toward sulfur impurities in the reactant stream. Using an economic model of an industrial deep hydrogenation process, we found that an increase in catalyst activity or lifetime of 2× would justify even a relatively high estimate for the cost of TiO2 atomic layer deposition coatings at scale

atomic layer↗

DOE OSTI2020

Atomic Layer Deposition Overcoating Improves Catalyst Selectivity and Longevity in Propane Dehydrogenation

Propylene, a precursor for commodity chemicals and plastics, is produced by propane dehydrogenation (PDH). An increase in PDH yield via added catalyst activity, lifetime, or selectivity represents significant energy and economic savings. Using Pt dispersed on Al2O3 extrudate supports as a commercially relevant model system, we demonstrate that atomic layer deposition (ALD) metal oxide overcoats, used to tailor metal-active sites, can increase PDH yield and selectivity. We investigate the interplay of Pt loading, ALD overcoat thickness, and Al 2 O 3 support surface area on PDH activity, selectivity, and catalyst stability to show that applying a 6-8 A thick layer of Al 2 O 3 on low-surface area Al 2 O 3 supports of similar to 90 m 2 /g surface area yields the optimal combination of stability and activity, while increasing propylene selectivity from 91 to 96%. Increased stability upon steaming deactivation occurs because the Al 2 O 3 overcoat prevents the Pt nanoparticles from sintering. We speculate that the ALD overcoat selectively binds to the undercoordinated sites on the Pt nanoparticles, while leaving the more selective terrace sites available for dehydrogenation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗