Search NASA⌕ Search

Engineering topics

Daniel Goodell

Publications and source records attributed to Daniel Goodell.

7 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2022

Maturation of Dynamic Power Convertors for RPS Robotic Space Exploration

NASA is developing dynamic power conversion technologies for future robotic space science and exploration missions powered by Radioisotope Power Systems (RPS). The Dynamic Radioisotope Power Systems (DRPS) Project is working to mature numerous dynamic power convertors and controllers for potential infusion into future flight generators. Maturation of power conversion technologies is being managed by the RPS Program and executed by the DRPS Project and Thermal Energy Conversion Branch located at NASA’s Glenn Research Center (GRC). Convertor maturation includes multiple convertor technology development contracts to deliver new prototypes and continued testing of relevant legacy convertors, commissioned during past projects. The convertor technology development contracts include two Stirling contractor teams and one Brayton team. All contracts have now completed prototype fabrication and testing planned during Phase 2. Government assessment of the new prototypes includes verification of performance in relevant environments and validation of the design with a focus on robustness.

Scott Wilson↗
NASA NTRSDate not supplied

Nuclear Electric Propulsion Brayton Power Conversion Working Fluid Considerations

NASA has considered Nuclear Electric Propulsion (NEP) for high ∆V missions since the late 1950s, but the current technology readiness level of the requisite power-train needs to be raised for such a mission. The powertrain includes reactor, power conversion, power management, electric propulsion, and thermal management components that must be integrated to minimize system a (kg/kWe) and to finalize a propulsion system architecture within the 2025-2027 timeframe requires advancing these component technologies to technology readiness level (TRL) 5 and Advancement Degree of Difficulty (AD2) 3 in an expeditious manner with minimal risks. This paper will only address the power conversion (heat to electric) components of that system. Based on both internal and industry studies, a primary conclusion of this work is that a single-spool supercritical Xe-He radial flux Brayton heat engine combined with a permanent magnet synchronous alternator can potentially be developed with the least technical risk to meet the technology readiness schedule and required NEP system performance metrics.

Nuclear Electric Propulsion (NEP)↗
NASA NTRSDate not supplied

Nuclear Electric Propulsion Brayton Power Conversion Working Fluid Considerations

NASA has considered Nuclear Electric Propulsion (NEP) for high V missions since the late 1950’s, but the current technology readiness level of the requisite powertrain needs to be raised for such a mission. The powertrain includes reactor, power conversion, power management, electric propulsion, and thermal management components that must be integrated to minimize system (kg/kWe) and to finalize a propulsion system architecture within the 2025-2027 timeframe requires advancing these component technologies to technology readiness level (TRL) 5 and Advancement Degree of Difficulty (AD2) 3 in an expeditious manner with minimal risks. This paper will only address the power conversion (heat to electric) components of that system. Based on both internal and industry studies, a primary conclusion of this work is that a single-spool supercritical Xe-He radial flux Brayton heat engine combined with a permanent magnet synchronous alternator can potentially be developed with the least technical risk to meet the technology readiness schedule and required NEP system performance metrics.

Nuclear↗
NASA NTRSDate not supplied

Consolidation of A Sodium Heat Pipe and Stirling Engine for Fission Surface Power

The Consolidated Heat Pipe (CHP) is a new design in which a sodium heat pipe is welded directly to the hot end of the Stirling engine to deliver thermal power more efficiently. The new integrated interface aims to reduce the large temperature drop (about 120 °C) that was measured across the bolted clamp joint between the Stirling engine and the heat pipes during the Kilopower Reactor Using Stirling TechnologY (KRUSTY) test from 2018. Initial testing and characterization of the CHP was performed in ambient air at the NASA Glenn Research Center (GRC). In the test, the heat pipe evaporator section was heated with a tube furnace. The thermal power was then transported to the Stirling engine integrated with a linear alternator that produced electrical power. The CHP has been tested at a hot end temperature ranging from 600 °C - 800 °C and a variety of other Stirling engine parameters (cold end temperature, piston amplitude and pressure). The results show that the temperature drop between the Stirling engine and the heat pipe has been reduced to 2°C - 4 °C. An overall temperature drop of 20 °C – 60 °C was also noted within the heat pipe depending on the combination of parameters mentioned above. Overall, it has been shown that the new Consolidated Heat Pipe design significantly improved the thermal interface to the Stirling engine.

Consolidated↗
NASA NTRSDate not supplied

Consolidation of A Sodium Heat Pipe and Stirling Engine for Fission Surface Power

The Consolidated Heat Pipe (CHP) is a new design in which a sodium heat pipe is welded directly to the hot end of the Stirling engine to deliver thermal power more efficiently. The new integrated interface aims to reduce the large temperature drop (about 120 °C) that was measured across the bolted clamp joint between the Stirling engine and the heat pipes during the Kilopower Reactor Using Stirling TechnologY (KRUSTY) test from 20181. Initial testing and characterization of the CHP was performed in ambient air at the NASA Glenn Research Center (GRC). In the test, the heat pipe evaporator section was heated with a tube furnace. The thermal power was then transported to the Stirling engine integrated with a linear alternator that produced electrical power. The CHP has been tested at a hot end temperature ranging from 600 °C - 800 °C and a variety of other Stirling engine parameters (cold end temperature, piston amplitude and pressure). The results show that the temperature drop between the Stirling engine and the heat pipe has been reduced to 2°C - 4 °C. An overall temperature drop of 20 °C – 60 °C was also noted within the heat pipe depending on the combination of parameters mentioned above. Overall, it has been shown that the new Consolidated Heat Pipe design significantly improved the thermal interface to the Stirling engine.

Consolidated↗
NASA NTRSDate not supplied

Vacuum Operation of Consolidated Heat Pipe (CHP) for Fission Surface Power

Consolidated Heat Pipe (CHP) is a new technology that enables direct thermal power delivery to the hot-end of a Stirling engine using a heat pipe--a two phase passive heat transfer device. CHP was developed after the efforts of the Kilopower Using Stirling TechnologY (KRUSTY) test where a heat pipe was used to deliver thermal power from a fission-basedreactor to a Stirling engine to produce 1 kWe of useable electrical power in 2018. Large thermal losses were noted during the KRUSTY test where a temperature drop of 145 °C was measured between the heat pipe’s condenser and the engine’s hot-end. The Consolidated Heat Pipe was designed to address and mitigate this temperature loss. CHP was designed, built and tested at the Glenn Research Center (GRC). The initial test was performed in ambient air conditions, and the results were presented in “Consolidation of a Sodium Heat Pipe and Stirling Engine for Fission Surface Power” at the Thermal Fluids Analysis Workshop in 2023. Researchers at GRC have tested this technology again in a vacuum environment in 2024. Results show that the heat pipe and the hot-end of the Stirling engine are isothermal with a minimal temperature differential of approximately 2.5 °C in varying operational states. The Consolidated Heat Pipe technology has proven to be an efficient way of delivering thermal power directly to Stirling engines.

Greeta J Thaikattil↗