Search NASA⌕ Search

Engineering topics

Das, A.

Publications and source records attributed to Das, A..

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Beam test performance studies of CMS Phase-2 Outer Tracker module prototypes

A new tracking detector will be installed as part of thePhase-2 upgrade of the CMS detector for the high-luminosity LHC era.This tracking detector includes the Inner Tracker, equipped withsilicon pixel sensor modules, and the Outer Tracker, consisting ofmodules with two parallel stacked silicon sensors. The Outer Trackerfront-end ASICs will be able to correlate hits from chargedparticles in these two sensors to perform on-module discriminationof transverse momenta (p$_{T}$). The p$_{T}$information is generated at a frequency of 40 MHz and will be usedin the Level-1 trigger decision of CMS. Prototypes of theso-called 2S modules were tested at the Test Beam Facility at DESYHamburg between 2019 and 2020. These modules use the finalfront-end ASIC, the CMS Binary Chip (CBC), and for the firsttime the Concentrator Integrated Circuit (CIC), optical readoutand on-module power conversion. In total, seven modules were tested,one of which was assembled with sensors irradiated with protons. Animportant aspect was to show that it is possible to read out modulessynchronously. A cluster hit efficiency of about 99.75 % wasachieved for all modules. The CBC p$_{T}$ discriminationmechanism has been verified to work together with the CIC andoptical readout. The measured module performance meets therequirements for operation in the upgraded CMS tracking detector.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2024

Measurement of the fractional radiation length of a pixel module for the CMS Phase-2 upgrade via the multiple scattering of positrons

High-luminosity particle collider experiments such as theones planned at the High-Luminosity Large Hadron Collider requireever-greater vertexing precision of the tracking detectors,necessitating reductions in the material budget of the detectors.Traditionally, the fractional radiation length (x/X$_{0}$) ofdetectors is either estimated using known properties of theconstituent materials, or measured in dedicated runs of the finaldetector. In this paper, we present a method of direct measurementof the material budget of a CMS prototype module designed for thePhase-2 upgrade of the CMS detector using a 40–65 MeV positronbeam. A total of 630 million events were collected at the PaulScherrer Institut PiE1 experimental area using a three-planetelescope consisting of the prototype module as the central plane,surrounded by two MALTA monolithic pixel detectors. Fractionalradiation lengths were extracted from scattering angle distributionsusing the Highland approximation for multiple scattering. Astatistical technique recovered runs suffering from triggerdesynchronisation, and several corrections were introduced tocompensate for local inefficiencies related to geometric and beamshape constraints. Two regions of the module were surveyed andyielded average x/X$_{0}$ values of (0.72 ± 0.05)% and(0.95 ± 0.09)%, which are compatible with empirical estimatesfor these regions computed from known material properties of 0.753%and 0.892%, respectively. Two types of higher-granularity maps ofthe fractional radiation length were produced, subdivided eitherinto rectangular regions of uniform size, or polygonal-shapedregions of uniform material composition. The results bode well forthe CMS Phase-2 upgrade modules, which will play a key role in theminimisation of the material of the upgraded detector.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2024

Correlations of event activity with hard and soft processes in p + Au collisions at $\sqrt{s_{NN}}$ = 200 GeV at the RHIC STAR experiment

With the STAR experiment at the BNL Relativistic Heavy Ion Collider, we characterize $\sqrt{s_{NN}}$ = 200GeV p + Au collisions by event activity (EA) measured within the pseudorapidity range η ϵ[–5,–3.4] in the Au-going direction and report correlations between this EA and hard- and soft-scale particle production at midrapidity (η ϵ[–1,1]). At the soft scale, charged particle production in low-EA p + Au collisions is comparable to that in p + p collisions and increases monotonically with increasing EA. At the hard scale, we report measurements of high transverse momentum (p T ) jets in events of different EAs. In contrast with the soft particle production, high-p T particle production and EA are found to be inversely related. Furthermore, to investigate whether this is a signal of jet quenching in high-EA events, we also report ratios of p T imbalance and azimuthal separation of dijets in high- and low-EA events. Within our measurement precision, no significant differences are observed, disfavoring the presence of jet quenching in the highest 30% EA p + Au collisions at $\sqrt{s_{NN}}$ = 200GeV.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2024

Measurements of charged-particle multiplicity dependence of higher-order net-proton cumulants in p + p collisions at $\sqrt{s}$ = 200 GeV from STAR at RHIC

We report on the charged-particle multiplicity dependence of net-proton cumulant ratios up to sixth order from $\sqrt{s}$ = 200 GeV p+p collisions at the Relativistic Heavy Ion Collider (RHIC). The measured ratios C 4 /C 2 , C 5 /C 1 , and C 6 /C 2 decrease with increased charged-particle multiplicity and rapidity acceptance. Neither the Skellam baselines nor PYTHIA8 calculations account for the observed multiplicity dependence. In addition, the ratios C 5 /C 1 and C 6 /C 2 approach negative values in the highest-multiplicity events, which implies that thermalized QCD matter may be formed in p+p collisions.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2024

Observation of the antimatter hypernucleus $^4_{\bar{\Lambda}}\overline{\hbox{H}}$

Matter-antimatter asymmetry is a research topic of fundamental interest, as it is the basis for the existence of the matter world, which survived annihilation with antimatter in the early Universe. High energy nuclear collisions create conditions similar to the Universe microseconds after the Big Bang, with comparable amounts of matter and antimatter. Much of the antimatter created escapes the rapidly expanding fireball without annihilation, making such collisions an effective experimental tool to create heavy antimatter nuclear objects and study their properties. In this paper, we report the first observation of the antimatter hypernucleus $^4_{\bar{\Lambda}}\overline{\hbox{H}}$, composed of an $\bar{\Lambda}$, an antiproton and two antineutrons. The discovery was made through its two-body decay after production in ultrarelativistic heavy ion collisions by the STAR experiment at the Relativistic Heavy Ion Collider. In total, 15.6 candidate $^4_{\bar{\Lambda}}\overline{\hbox{H}}$ antimatter hypernuclei are obtained with an estimated background count of 6.4. Lifetimes of the antihypernuclei $^3_{\bar{\Lambda}}\overline{\hbox{H}}$ and $^4_{\bar{\Lambda}}\overline{\hbox{H}}$ are measured and compared with lifetimes of their corresponding hypernuclei, testing the symmetry between matter and antimatter. Various production yield ratios among (anti)hypernuclei and (anti)nuclei are also measured and compared with theoretical model predictions, shedding light on their production mechanism.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Exclusive J / ψ , ψ ( 2 s ) , and e + e - pair production in Au + Au ultraperipheral collisions at the BNL Relativistic Heavy Ion Collider

Measurements of exclusive J/ψ, ψ(2⁢s), and electron-positron (e + ⁢e - ) pair photoproduction in Au+Au ultraperipheral collisions are reported by the STAR experiment at $\sqrt{s_{NN}}$ = 200GeV. Here, we report several first measurements at the BNL Relativistic Heavy Ion Collider, which are (i) J/ψ photoproduction with large momentum transfer up to 2.2⁢(GeV/c) 2 , (ii) coherent J/ψ photoproduction associated with neutron emissions from nuclear breakup, (iii) the rapidity dependence of incoherent J/ψ photoproduction, (iv) the ψ⁡(2⁢s) photoproduction cross section at midrapidity, and (v) e + ⁢e - pair photoproduction up to high invariant mass of 6GeV/c 2 . For measurement (ii), the coherent J/ψ total cross section of γ + Au → J/ψ + Au as a function of the center-of-mass energy W γN has been obtained without photon energy ambiguities. The data are quantitatively compared with the Monte Carlo models STARlight, Sartre, BeAGLE, and theoretical calculations of gluon saturation with color glass condensate, nuclear shadowing with leading twist approximation, quantum electrodynamics, and the next-to-leading-order perturbative QCD. At the photon-nucleon center-of-mass energy of 25.0 GeV, the coherent and incoherent J/ψ cross sections of Au nuclei are found to be 71% ± 10% and 36% ± 7%, respectively, of that of free protons. These data provide an important experimental constraint for nuclear parton distribution functions and a unique opportunity to advance the understanding of the nuclear modification effect at the top RHIC energy.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2024

Observation of Strong Nuclear Suppression in Exclusive J/ψ Photoproduction in Au + Au Ultraperipheral Collisions at RHIC

We report a measurement of exclusive J/ψ and ψ⁡(2⁢s) photoproduction in Au+Au ultraperipheral collisions at √s NN = 200 GeV using the STAR detector. For the first time, (i) the ψ⁡(2⁢s) photoproduction in midrapidity at the Relativistic Heavy-Ion Collider has been experimentally measured; (ii) nuclear suppression factors are measured for both the coherent and incoherent J/ψ production. At average photon-nucleon center-of-mass energy of 25.0 GeV, the coherent and incoherent J/ψ cross sections of Au nuclei are found to be 71 ±10% and 36 ±7%, respectively, of that of free protons. The stronger suppression observed in the incoherent production provides a new experimental handle to study the initial-state parton density in heavy nuclei. As a result, data are compared with theoretical models quantitatively.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2024

Estimate of background baseline and upper limit on the chiral magnetic effect in isobar collisions at $\sqrt{S_{NN}}$=200 GeV at the BNL Relativistic Heavy Ion Collider

For the search of the chiral magnetic effect (CME), STAR previously presented the results from isobar collisions ($^{96}_{44}$Ru + $^{96}_{44}$Ru, $^{96}_{40}$Zr + $^{96}_{40}$Zr) obtained through a blind analysis. The ratio of results in Ru+Ru to Zr+Zr collisions for the CME-sensitive charge-dependent azimuthal correlator (Δ⁢𝛾), normalized by elliptic anisotropy (𝑣2), was observed to be close to but systematically larger than the inverse multiplicity ratio. The background baseline for the isobar ratio, 𝑌= (Δ⁢𝛾/𝑣2) Ru /(Δ⁢𝛾/𝑣2) Zr , is naively expected to be (1/𝑁) Ru /(1/𝑁) Zr ; however, genuine two- and three-particle correlations are expected to alter it. We estimate the contributions to 𝑌 from those correlations, utilizing both the isobar data and hijing simulations. After including those contributions, we arrive at a final background baseline for 𝑌, which is consistent with the isobar data. Here, we extract an upper limit for the CME fraction in the Δ⁢𝛾 measurement of approximately 10% at a 95% confidence level on in isobar collisions at $\sqrt{S_{NN}}$=200 GeV, with an expected 15% difference in their squared magnetic fields.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2024

Upper limit on the chiral magnetic effect in isobar collisions at the Relativistic Heavy-Ion Collider

The chiral magnetic effect (CME) is a phenomenon that arises from the QCD anomaly in the presence of an external magnetic field. The experimental search for its evidence has been one of the key goals of the physics program of the Relativistic Heavy-Ion Collider. The STAR Collaboration has previously presented the results of a blind analysis of isobar collisions ( Ru 44 96 + Ru 44 96 , Zr 40 96 + Zr 40 96 ) in the search for the CME. The isobar ratio ( Y ) of CME-sensitive observable, charge separation scaled by elliptic anisotropy, is close to but systematically larger than the inverse multiplicity ratio, the naive background baseline. This indicates the potential existence of a CME signal and the presence of remaining nonflow background due to two- and three-particle correlations, which are different between the isobars. In this postblind analysis, we estimate the contributions from those nonflow correlations as a background baseline to Y , utilizing the isobar data as well as Heavy Ion Jet Interaction Generator simulations. This baseline is found consistent with the isobar ratio measurement, and an upper limit of 10% at 95% confidence level is extracted for the CME fraction in the charge separation measurement in isobar collisions at s NN = 200 GeV. Published by the American Physical Society 2024

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2024

Collision-energy dependence of deuteron cumulants and proton-deuteron correlations in Au+Au collisions at RHIC

We report the first measurements of cumulants, up to 4th order, of deuteron number distributions and proton-deuteron correlations in Au+Au collisions recorded by the STAR experiment in phase-I of Beam Energy Scan (BES) program at the Relativistic Heavy Ion Collider. Deuteron cumulants, their ratios, and proton-deuteron mixed cumulants are presented for different collision centralities covering a range of center-of-mass energy per nucleon pair $\sqrt{s_{NN}} = 7.7$ to 200 GeV. It is found that the cumulant ratios at lower collision energies favor a canonical ensemble over a grand canonical ensemble in thermal models. An anti-correlation between proton and deuteron multiplicity is observed across all collision energies and centralities, consistent with the expectation from global baryon number conservation. The UrQMD model coupled with a phase-space coalescence mechanism qualitatively reproduces the collision-energy dependence of cumulant ratios and proton-deuteron correlations.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
NASA NTRS2018

Oceanus: A High Science Return Uranus Orbiter with a Low-Cost Instrument Suite

Ice-giant-sized planets are the most common type of observed exoplanet, yet the two ice giants in our own solar system (Uranus and Neptune) are the least explored class of planet, having only been observed through ground-based observations and a single flyby each by Voyager 2 approximately 30 years ago. These single flybys were unable to characterize the spatial and temporal variability in ice giant magnetospheres, some of the most odd and intriguing magnetospheres in the solar system. They also offered only limited constraints on the internal structure of ice giants; understanding the internal structure of a planet is important for understanding its formation and evolution. The most recent planetary science Decadal Survey by the U.S. National Academy of Sciences, ''Vision and Voyages for Planetary Science in the Decade 2013-2022,'' identified the ice giant Uranus as the third highest priority for a Flagship mission in the decade 2013-2022. However, in the event that NASA or another space agency is unable to fly a Flagship-class mission to an ice giant in the next decade, this paper presents a mission concept for a focused, lower cost Uranus orbiter called OCEANUS (Origins and Composition of the Exoplanet Analog Uranus System). OCEANUS would increase our understanding of the interior structure of Uranus, its magnetosphere, and how its magnetic field is generated. These goals could be achieved with just a magnetometer and the spacecraft's radio system. This study shows that several of the objectives outlined by the Decadal Survey, including one of the two identified as highest priority, are within reach for a New-Frontiers-class mission.

Elder, C. M.↗
NASA NTRS1993

Modeling, system identification, and control of ASTREX

The modeling, system identification and controller design aspects of the ASTREX precision space structure are presented in this work. Modeling of ASTREX is performed using NASTRAN, TREETOPS and I-DEAS. The models generated range from simple linear time-invariant models to nonlinear models used for large angle simulations. Identification in both the time and frequency domains are presented. The experimental set up and the results from the identification experiments are included. Finally, controller design for ASTREX is presented. Simulation results using this optimal controller demonstrate the controller performance. Finally the future directions and plans for the facility are addressed.

Abhyankar, Nandu S.↗
NASA NTRS1990

The sixth generation robot in space

The knowledge based simulator developed in the artificial intelligence laboratory has become a working test bed for experimenting with intelligent reasoning architectures. With this simulator, recently, small experiments have been done with an aim to simulate robot behavior to avoid colliding paths. An automatic extension of such experiments to intelligently planning robots in space demands advanced reasoning architectures. One such architecture for general purpose problem solving is explored. The robot, seen as a knowledge base machine, goes via predesigned abstraction mechanism for problem understanding and response generation. The three phases in one such abstraction scheme are: abstraction for representation, abstraction for evaluation, and abstraction for resolution. Such abstractions require multimodality. This multimodality requires the use of intensional variables to deal with beliefs in the system. Abstraction mechanisms help in synthesizing possible propagating lattices for such beliefs. The machine controller enters into a sixth generation paradigm.

Butcher, A.↗
NASA NTRS1990

Startup thaw concept for the SP-100 space reactor power system

A thaw concept for a space reactor power system which employs lithium as a circulant for both the heat-transport and the heat-rejection fluid loops is presented. An exemplary thermal analysis for a 100-kWe (i.e., SP-100) system is performed. It is shown that the design of the thaw system requires a thorough knowledge of the various physical states of the circulant throughout the system, both spatially and temporally, and that the design has to provide adequate margins for the system to avoid a structural or thermally induced damage.

Kirpich, A.↗
NASA NTRS1988

Planning actions in robot automated operations

Action planning in robot automated operations requires intelligent task level programming. Invoking intelligence necessiates a typical blackboard based architecture, where, a plan is a vector between the start frame and the goal frame. This vector is composed of partially ordered bases. A partial ordering of bases presents good and bad sides in action planning. Partial ordering demands the use of a temporal data base management system.

Das, A.↗