Engineering topics

Dauenhauer, Paul J.

Publications and source records attributed to Dauenhauer, Paul J..

5 records

DOE OSTI2024

ATLAS-MAP: An Automated Test Station for Gated Electronic Transport Measurements

The diversification of electronic materials in devices provides a strong incentive for methods to rapidly correlate device performance with fabrication decisions. In this work, we present a low-cost automated test station for gated electronic transport measurements of field-effect transistors. Utilizing open-source PyMeasure libraries for transparent instrument control, the “ATLAS-MAP” system serves as a customizable interface between sourcemeters and samples under test and is programmed to conduct transfer curve and van der Pauw methods with static and sweeping gate voltages. Zinc oxide transistors of variable thickness (5, 10, and 20 nm) and channel size (50 μm to 3 mm, of equal length and width) were fabricated to validate the design. Standardization of testing procedures and raw data formatting enabled automated data analysis. A detailed list of parts and code files for the system are provided.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Finding a natural rhythm

Paul J. Dauenhauer describes the mathematical basis for designing dynamic catalysts that are programmed to change with time.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2024

Catalytic Hydrogenation of Alkylphenols for Renewable Caprolactone

Selective hydrogenation of lignin-derived alkyl-phenol to alkyl-cyclohexanone is a key step in the synthesis of renewable caprolactone from lignin-derived monomers. Selective hydrogenation of p-cresol, a model compound for lignin-derived monomers, to 4-methyl-cyclohexanone was conducted using Pd/γ-Al 2 O 3 in a continuous three-phase flow reactor with side products of 4-methyl cyclohexanol. High conversion (85%) and selectivity (>93%) were demonstrated at ambient reaction pressure. Evaluation of the hydrogenation at different reaction parameters showed that the reaction selectivity was determined by the surface coverage of p-cresol and 4-methyl cyclohexanone. Furthermore, high selectivity to 4-methyl cyclohexanone was also attributed to the lower apparent activation barrier of p-cresol hydrogenation (67 ± 2 kJ mol –1 ) compared to that of hydrogenation 4-methyl cyclohexanone (92 ± 11 kJ mol –1 ), with a faster rate of initial hydrogenation of p-cresol relative to carbonyl hydrogenation of 4-methyl-cyclohexanone.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Accelerated Steam Methane Reforming by Dynamically Applied Charges

Catalyst design has traditionally focused on tuning active site properties to optimally bind reaction intermediates and balance the kinetic requirements of multiple competing chemical processes, as necessitated by the Sabatier principle. It has recently been proposed that for reactions following certain potential energy landscapes, the activity limit imposed by the Sabatier principle may be overcome by using programmed oscillations of surface electron density at the timescales of surface reactions (i.e., “catalytic resonance”). Here, we use a combination of density functional theory (DFT) simulations and transient kinetic models (TKMs) to simulate the kinetics of steam methane reforming (SMR) on Ru(211) surfaces under statically and dynamically applied charges. DFT-calculated binding energies of SMR intermediates and transition states exhibit strong sensitivity to positively applied charges and follow unique scaling relationships that deviate from linear periodic trends across transition metals. Our simulations demonstrate that applying a small positive charge to Ru dramatically enhances the steady-state turnover frequency (TOF) of SMR by up to 5 orders of magnitude above the TOF observed over neutral Ru. Thus, statically charging Ru catalysts may be an effective strategy to lower the temperature requirements for SMR. Dynamic square-wave oscillations in charge resulted in SMR catalytic resonance with an onset frequency f ∼ 106 Hz and the corresponding average TOFs exceeding the statically charged Ru surface by an additional 15%. Here, based on sensitivity analyses performed for the two end points of oscillation, we propose that dynamic TOF improvement beyond the Sabatier maximum can be expected when the system oscillates between two kinetic regimes that are uniquely controlled by distinct elementary steps.

Catalysts↗

DOE OSTI2024

Alumina–Titania Nanolaminate Condensers for Hot Programmable Catalysis

Nanolaminates composed of thin alternating layers of Al2O 3 and TiO 2 (ATO) were engineered by using atomic layer deposition as the dielectric material for a Pt-on-carbon catalytic condenser. Investigation assessed synthesis parameters including the deposition temperature, Al 2 O 3 and TiO 2 layer thicknesses, total number of layers, and a capping Al 2 O 3 layer on the maximum charge accumulation in the Pt catalyst. The highest capacitance ATO configuration demonstrated a specific capacitance of ∼1200 nF/cm 2 with working voltages of ±5 V, enabling the storage of 4 × 10 13 electrons or holes per cm 2 at room temperature. The ATO devices exhibited enhanced capacitance at elevated temperatures of up to 400 °C, suggesting the suitability of these materials for high-temperature applications. Adsorption of carbon monoxide on the Pt/C-ATO device characterized by grazing incidence infrared spectroscopy showed changes in the surface binding energy of 13.1 ± 0.8 kJ/mol for an applied external voltage bias of ±1 V.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗