Search NASA⌕ Search

Engineering topics

Davenport, Edwin E.

Publications and source records attributed to Davenport, Edwin E..

4 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1961

Effects of Geometric Variations on Lift Augmentation of Simple-plenum-chamber Ground-effect Models

Considerable interest has been shown during recent years in ground-effect vehicles. Of the various types proposed, the simple-plenum-chamber vehicle has indicated promise because, although the lift augmentation obtainable appears to be less than that of an annular jet, it may be somewhat less complicated structurally. The present investigation was undertaken to study the effects of some geometric variations upon lift augmentation of a simple plenum chamber within ground proximity. The variables included the ratio inlet area to exit area, plenum-chamber depth, and entrance configuration. An optimum plenum-chamber depth appeared to be between 3 and 10 percent of the plenum-chamber diameter with a ratio of inlet diameter to plenum-chamber diameter of 0.15 for the range of plenum-chamber depths investigated. The most important effect of multiple inlets was the elimination of negative lift augmentation, which was experienced with single sharp-edged inlets, at intermediate heights. Installation of a flared inlet and a turning-vane assembly improved lift augmentation of a single-inlet configuration at intermediate heights.

Davenport, Edwin E.↗
NASA NTRS1960

Thrust Characteristics of Multiple Lifting Jets in Ground Proximity

An investigation has been made to determine the thrust characteristics within ground proximity of a series of models which might represent vertical take-off-and-landing (VTOL) aircraft with multiple exit jet engines exhausting vertically downward beneath a lifting surface. Variations in simulated engine configurations were provided by a series of nozzle insert plugs in which the number of jet exits, located symmetrically on a fixed circle, was varied, or the diameter of the circle was varied for a given number of jet exits. represent lifting surfaces, and high-pressure air was used to simulate jet-engine exhaust. Plywood plates were used to The results of the investigation showed that increasing the number of exits, such that an annular jet configuration was approached, provided more favorable thrust characteristics within ground proximity than any other variation in the geometry of these multiple jets. Tests of a configuration with two nozzles approximating a fan-in-wing VTOL aircraft with fans located at different spanwise locations indicated that the augmentation in thrust within ground proximity was greater for the arrangement with the more inboard location of the nozzles.

Davenport, Edwin E.↗
NASA NTRS1958

Low-Speed Aerodynamic and Hydrodynamic Characteristics of a Proposed Supersonic Multijet Water-Based Hydro-Ski Aircraft with Upward-Rotating Engines

The low-speed aerodynamic and hydrodynamic characteristics of a proposed multijet water-based aircraft configuration for supersonic operation have been investigated. The design features include upward-rotating engines, body indentation, a single hydro-ski, and a wing with an aspect ratio of 3.0, a taper ratio of 0.143, 36.90 sweepback of the quarter-chord line, and NACA 65AO04 airfoil sections. For the aerodynamic investigation, with the flaps retracted, the model was longitudinally and directionally stable up to the stall. The all-movable horizontal tail was capable of trimming the model up to a lift coefficient of approximately 0.87. All flap configurations investigated had a tendency to become longitudinally unstable at stall. The effectiveness of the all-movable horizontal tail increased with increasing lift coefficient for all flap configurations investigated; however, with the large static margin of the configuration with the center of gravity at 0.25 mean aerodynamic chord, the all-movable horizontal tail was not powerful enough to trim all the various flapped configurations investigated throughout the angle-of-attack range. For the hydrodynamic investigation, longitudinal stability during take-offs and landings was satisfactory. Decreasing the area of the hydro-ski 60 percent increased the maximum resistance and emergence speed 40 and 70 percent, respectively. Without the jet exhaust, the resistance was reduced by simulating the vertical-lift component of the forward engines rotated upward. However, the jet exhaust of the forward engines increased the maximum resistance approximately 60 percent. The engine inlets and horizontal tail were free from spray for all loads investigated and for both hydro-ski sizes.

Petynia, William W.↗