Search NASA⌕ Search

Engineering topics

David L Ellis

Publications and source records attributed to David L Ellis.

9 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2021

The Effect of Composition on Microstructure and Properties for Additively Manufactured Superalloy 718

Additive manufacturing (AM) represents an exciting new approach towards producing metallic aerospace components. The ability to make complex geometries that were impossible to create using conventional manufacturing methods has sparked interest from the aerospace community, including NASA. The use of AM components for crucial and human rated space missions necessitates a full characterization of the differences between AM and more conventional wrought and cast processes. For this study, sixteen different commercially available superalloy 718 powder feedstocks were obtained, built using laser powder bed fusion(L-PBF), and microstructurally and mechanically analyzed. These measurements revealed a wide range of build qualities and microstructures despite all powder lots falling within the 718chemical specification and being processed using the same prescribed build and heat treatment parameters. Statistical analysis found a strong correlation of the amount of carbon in the powder with the final grain size and strength of the heat-treated 718 part. Ultimately, this study highlights the need of a refined superalloy 718 chemical specification for powder lots to be used in AM.

Timothy M Smith↗
NASA NTRS2020

In-Situ Alloying of GRCop-42 via Additive Manufacturing: Precipitate Analysis

In situ alloying of elemental Cu, Cr, and Nb to form GRCop-42 (Cu-4at. % Cr-2at. % Nb)using laser powder bed fusion (LPBF) additive manufacturing (AM) was successful. Evaluation of the in situ alloyed GRCop-42(ISGRCop-42) was conducted using phase extraction to explore the effects of AM process conditions on the formation of Cr2Nb precipitates from elemental powders. It was found that ISGRCop-42successfully and repeatedly formed Cr2Nb at a yield as high as 89%of potential Cr2Nbcontent. Initial work shows that powder preparation was the most influential factor in alloying success, followed by laser power.

Additive Manufacturing↗
NASA NTRS1993

Effect of hydrogen exposure on a Cu-8 Cr-4 Nb alloy

The advanced regeneratively cooled rocket thrust chamber may require new materials to achieve long life and improved performance. Current materials such as NARloy-Z (Cu-3 wt. percent Ag-0.5 wt. percent Zr), while highly conductive, do not have sufficient high temperature strength and creep resistance to meet the projected needs of advanced rocket motors. A Cu-8 at. percent Cr-4 at. percent Nb (Cu-8 Cr-4 Nb) alloy has been identified as a promising material for this application. However, hydrogen embrittlement is a concern given the presence of high pressure, high temperature hydrogen in regeneratively cooled rocket motors. Thermodynamic analysis of the reaction between Cr-rich Cr2Nb and H2 showed that there is a possibility of reaction at temperatures up to 323 K in a 35 MPa H2 environment. Above 323 K the pressure necessary to achieve reaction rapidly increased beyond the range experienced in rocket motors. Tensile specimens exposed in 34.5 MPa H2 at room temperatures and during cycling to 705 C did not show any degradation of properties. No evidence of reaction was observed for Cr2Nb precipitate observed on the fracture surfaces. Based on these results the Cu-8 Cr-4 Nb alloy was judged to be sufficiently stable for use in rocket motors.

David L Ellis↗
NASA NTRSDate not supplied

Lightweight Thrust Chamber Assemblies using Multi-Alloy Additive Manufacturing and Composite Overwrap

Additive Manufacturing (AM) has brought significant design and fabrication opportunities for complex components with internal features such as liquid rocket engine thrust chambers not previously possible. This technology allows for significant cost savings and schedule reductions in addition to new performance optimization through weight reduction and increased margins. Specific to regeneratively-cooled combustion chambers and nozzles for liquid rocket engines, additive manufacturing offers the ability to form the complex internal coolant channels and the closeout of the channels to contain the high pressure liquid propellants with a single operation. Much of additive manufacturing development has focused on monolithic alloys using Laser Powder Bed Fusion (L-PBF), which do not allow for complete optimization of the structure. The National Aeronautics and Space Administration (NASA) completed feasibility of an AM bimetallic L-PBF GRCop-84 copper-alloy combustion chamber with an AM electron beam freeform Inconel 625 structural jacket under the Low Cost Upper Stage Propulsion (LCUSP) Project. A follow-on project called Rapid Analysis and Manufacturing Propulsion Technology (RAMPT) is under development to further expand large-scale multi-alloy thrust chambers while maturing composite overwrap technology for significant weight savings opportunities. The RAMPT project has three primary objectives: 1) Advancing blown powder Directed Energy Deposition (DED) to fabricate integral-channel large scale nozzles, 2) Develop composite overwrap technology to reduce weight and provide structural capability for thrust chamber assemblies, and 3) Develop bimetallic and multi-metallic additively manufactured radial and axial joints to optimize material performance. In addition to these primary manufacturing developments, analytical modeling efforts compliment the process development to simulate the AM processes to reduce build failures and distortions. The RAMPT project is also maturing the supply chain for various manufacturing processes described above in addition to L-PBF of GRCop-42. This paper will present an overview of the RAMPT project, the process development and hardware progress to date, material and hot-fire testing results, along with future developments.

Additive Manufacturing↗
NASA NTRSDate not supplied

Nanomechanical Characterization of Additive Manufactured GRCop-42 Alloy Developed by Directed Energy Deposition Methods

Propulsion applications such as combustion chambers and nozzles for liquid rocket engines require the use of unique materials with superior mechanical and thermal properties. GRCop-42(Cu-4 wt.% Cr-2 wt.% Nb) is one such candidate material developed by NASA and is now being manufactured using additive manufacturing (AM) techniques. AM offers a unique processing environment different from traditional metal fabrication processes. This study characterized the mechanical and structural properties of as-deposited and heat-treated GRCop-42manufactured with Blown Powder Directed Energy Deposition (BPD)based on preliminary testing. The materials were characterized using several techniques including surface profiling by laser microscopy, mechanical stiffness by instrumented indentation, crystal structure, residual stress measurements using XRD and residual XRD, and chemical composition and microstructural evaluation using SEM with EBSD. The results of the study are compared using the BPD techniques for samples in the as-deposited and heat-treated conditions.

GRCop-42↗
NASA NTRSDate not supplied

Expansion of Additive Manufacturing Capabilities Into in Situ Alloying of Dispersion Strengthened, High Temperature Cu Alloys

New alloys and materials are potentially possible through additive manufacturing’s unique thermal history. Current literature explores the fabrication of eutectic and solid solution strengthened alloys through in-situ alloying, to take advantage of AM’s unique thermal history. The resulting lessons learned by in-situ alloying currently available materials will likely lead to the development of novel materials solely possible through in-situ alloying. This work will expand the application of in-situ alloying via additive manufacturing to NASA’s GRCop-42 (Cu-4at% Cr-2at% Nb), a high temperature copper alloy which has shown success in additively manufactured combustion chambers from pre-alloyed powders. GRCop-42 is unique to literature because a reaction to form the Cr2Nb dispersoids is required during the in-situ alloying. Both reaction completion rate and how input energy from the AM process influences the reaction progress will be evaluated. Ultimately, expansion of in-situ alloying capabilities provides further insight to develop novel materials using AM.

David Steven Scannapieco↗