Engineering topics

Davila, C. G.

Publications and source records attributed to Davila, C. G..

9 records

NASA NTRS2010

Analytical Modelling of Transverse Matrix Cracking of [plus or minus Theta/90(sub n)](sub s) Composite Laminates Under Multiaxial Loading

An analytical model based on the analysis of a cracked unit cell of a composite laminate subjected to multiaxial loads is proposed to predict the onset and accumulation of transverse matrix cracks in the 90(sub n) plies of uniformly stressed [plus or minus Theta/90(sub n)](sub s) laminates. The model predicts the effect of matrix cracks on the stiffness of the laminate, as well as the ultimate failure of the laminate, and it accounts for the effect of the ply thickness on the ply strength. Several examples describing the predictions of laminate response, from damage onset up to final failure under both uniaxial and multiaxial loads, are presented.

Mayugo, J A.↗

NASA NTRS2007

Prediction of Size Effects in Notched Laminates Using Continuum Damage Mechanics

This paper examines the use of a continuum damage model to predict strength and size effects in notched carbon-epoxy laminates. The effects of size and the development of a fracture process zone before final failure are identified in an experimental program. The continuum damage model is described and the resulting predictions of size effects are compared with alternative approaches: the point stress and the inherent flaw models, the Linear-Elastic Fracture Mechanics approach, and the strength of materials approach. The results indicate that the continuum damage model is the most accurate technique to predict size effects in composites. Furthermore, the continuum damage model does not require any calibration and it is applicable to general geometries and boundary conditions.

Camanho, D. P.↗

NASA NTRS2007

An Engineering Solution for Solving Mesh Size Effects in the Simulation of Delamination with Cohesive Zone Models

This paper presents a methodology to determine the parameters to be used in the constitutive equations of Cohesive Zone Models employed in the simulation of delamination in composite materials by means of decohesion finite elements. A closed-form expression is developed to define the stiffness of the cohesive layer. A novel procedure that allows the use of coarser meshes of decohesion elements in large-scale computations is also proposed. The procedure ensures that the energy dissipated by the fracture process is computed correctly. It is shown that coarse-meshed models defined using the approach proposed here yield the same results as the models with finer meshes normally used for the simulation of fracture processes.

FROM↗

NASA NTRS2006

A Damage Model for the Simulation of Delamination in Advanced Composites under Variable-Mode Loading

A thermodynamically consistent damage model is proposed for the simulation of progressive delamination in composite materials under variable-mode ratio. The model is formulated in the context of Damage Mechanics. A novel constitutive equation is developed to model the initiation and propagation of delamination. A delamination initiation criterion is proposed to assure that the formulation can account for changes in the loading mode in a thermodynamically consistent way. The formulation accounts for crack closure effects to avoid interfacial penetration of two adjacent layers after complete decohesion. The model is implemented in a finite element formulation, and the numerical predictions are compared with experimental results obtained in both composite test specimens and structural components.

Turon, A.↗

NASA NTRS2005

Failure Models and Criteria for FRP Under In-Plane or Three-Dimensional Stress States Including Shear Non-Linearity

A set of three-dimensional failure criteria for laminated fiber-reinforced composites, denoted LaRC04, is proposed. The criteria are based on physical models for each failure mode and take into consideration non-linear matrix shear behaviour. The model for matrix compressive failure is based on the Mohr-Coulomb criterion and it predicts the fracture angle. Fiber kinking is triggered by an initial fiber misalignment angle and by the rotation of the fibers during compressive loading. The plane of fiber kinking is predicted by the model. LaRC04 consists of 6 expressions that can be used directly for design purposes. Several applications involving a broad range of load combinations are presented and compared to experimental data and other existing criteria. Predictions using LaRC04 correlate well with the experimental data, arguably better than most existing criteria. The good correlation seems to be attributable to the physical soundness of the underlying failure models.

Pinho, Silvestre T.↗

NASA NTRS2001

Numerical Simulation of Delamination Growth in Composite Materials

The use of decohesion elements for the simulation of delamination in composite materials is reviewed. The test methods available to measure the interfacial fracture toughness used in the formulation of decohesion elements are described initially. After a brief presentation of the virtual crack closure technique, the technique most widely used to simulate delamination growth, the formulation of interfacial decohesion elements is described. Problems related with decohesion element constitutive equations, mixed-mode crack growth, element numerical integration and solution procedures are discussed. Based on these investigations, it is concluded that the use of interfacial decohesion elements is a promising technique that avoids the need for a pre-existing crack and pre-defined crack paths, and that these elements can be used to simulate both delamination onset and growth.

Camanho, P. P.↗

NASA NTRS1998

Analysis of Tile-Reinforced Composite Armor: Advanced Modeling and Strength Analyses - Part 1

The results of an analytical and experimental study of the structural response and strength of tile-reinforced components of the Composite Armored Vehicle are presented. The analyses are based on specialized finite element techniques that properly account for the effects of the interaction between the armor tiles, the surrounding elastomers, and the glass-epoxy sublaminates. To validate the analytical predictions, tests were conducted with panels subjected to three-point bending loads. The sequence of progressive failure events for the laminates is described. This paper describes the results of Part 1 of a study of the response and strength of tile-reinforced composite armor.

Davila, C. G.↗

NASA NTRS1994

Cross-surface interface element for coupling built-up structural subdomains

A new finite element for coupling built-up shell substructures is presented. The present work extends the hybrid variational formulation of the interface element developed by Aminpour and Ransom to permit coupling between two intersecting substructures. Designed for the assembly of independently built-up finite element models, this technique provides a level of modeling flexibility previously unavailable.

Davila, C. G.↗

NASA NTRS1993

Computation of strain energy release rates for skin-stiffener debonds modeled with plate elements

An efficient method for predicting the strength of debonded composite skin-stiffener configurations is presented. This method, which is based on fracture mechanics, models the skin and the stiffener with two-dimensional (2D) plate elements instead of three-dimensional (3D) solid elements. The skin and stiffener flange nodes are tied together by two modeling techniques. In one technique, the corresponding flange and skin nodes are required to have identical translational and rotational degrees-of-freedom. In the other technique, the corresponding flange and skin nodes are only required to have identical translational degrees-of-freedom. Strain energy release rate formulas are proposed for both modeling techniques. These formulas are used for skin-stiffener debond cases with and without cylindrical bending deformations. The cylindrical bending results are compared with plane-strain finite element results. Excellent agreement between the two sets of results is obtained when the second technique is used. Thus, from these limited studies, a preferable modeling technique for skin-stiffener debond analysis using plate elements is established.

Wang, J. T.↗