Search NASA⌕ Search

Engineering topics

Davis, D. D., Jr.

Publications and source records attributed to Davis, D. D., Jr..

16 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Analysis of bolt-loaded elliptical holes in laminated composite joints

The feasibility of changing the bolt shape from circular to elliptical in order to increase the joint strength was investigated. An analytical method using a cosine series to represent the bearing stress was derived, and a boundary collocation method was used to determine the unknown coefficients of this cosine series. Stresses at the hole edge predicted by the analytical method agreed very well with finite element solutions. Failure analyses of joints in two different laminates were performed, and each laminate exhibited a different joint failure mode. Results demonstrate that the joint strength of both laminates can be improved substantially by changing the bolt shape to elliptical. The joint that failed in a bearing mode showed a greater strength increase compared to the joint that failed in a shearing mode.

Wang, J. T.↗
NASA NTRS1993

An analytically designed subcomponent test to reproduce the failure of a composite wing box beam

A Stiffener Runout Test Specimen (SRTS) has been analyzed and tested to verify the failure scenario for a large composite wingbox beam subcomponent. The SRTS was taken from an undamaged region of the subcomponent that was similar to the failure region of the boxbeam. Extensive analyses were performed to determine the proper load introduction and constraint conditions required for the SRTS test to simulate the response of the subcomponent. The present paper describes the analyses that led to the design of test fixtures that ensured that the response of the SRTS duplicated the response of the box beam. The results of the SRTS test are described and compared with the analytical predictions.

Davis, D. D., Jr.↗
NASA NTRS1993

Technology integration box beam failure study

Composite structures have the potential to be cost-effective, structurally efficient primary aircraft structures. The Advanced Composites Technology (ACT) Program has the goal to develop the technology to exploit this potential for heavily loaded aircraft structures. As part of the ACT Program, Lockheed Aeronautical Systems Company completed the design and fabrication of the Technology Integration Box Beam (TIBB). The TIBB is an advanced composite prototype structure for the center wing section of the C-130 aircraft. Lockheed subjected the TIBB to downbending, upbending, torsion and combined upbending and torsion load conditions to verify the design. The TIBB failed at 83 percent of design ultimate load for the combined upbending and torsion load condition. The objective of this paper is to describe the mechanisms that led to the failure of the TIBB. The results of a comprehensive analytical and experimental study are presented. Analytical results include strain and deflection results from both a global analysis of the TIBB and a local analysis of the failure region. These analytical results are validated by experimental results from the TIBB tests. The analytical and experimental results from the TIBB tests are used to determine a sequence of events that resulted in failure of the TIBB. A potential cause of failure is high stresses in a stiffener runout region. Analytical and experimental results are also presented for a stiffener runout specimen that was used to simulate the TIBB failure mechanisms.

Shuart, M. J.↗
NASA NTRS1992

Technology integration box beam failure study

The objective of this paper is to describe current results from an on-going study of the mechanisms that led to the failure of the TIBB. Experimental and analytical results are presented. Experimental results include load, strain, and deflection data for the TIBB (Technology Integration Box Beam). An analytical investigation was conducted to compliment the experimental investigation and to gain additional insight into the TIBB structural response. Analytical results include strain and deflection results from a global analysis of the TIBB. A local analysis of the failure region is being completed. These analytical results are validated through comparisons with the experimental results from the TIBB tests. The experimental and analytical results from the TIBB tests are used to determine a sequence of events that may have resulted in failure of the TIBB. A potential cause of failure is high stresses in a stiffener runout region. Typical analytical results are presented for a stiffener runout specimen that is being defined to simulate the TIBB failure mechanisms. The results of this study are anticipated to provide better understanding of potential failure mechanisms in composite aircraft structures, to lead to future design improvements, and to identify needed analytical tools for design and analysis.

Shuart, Mark J.↗
NASA NTRS1992

Technology integration box beam failure study

Composite structures have the potential to be cost effective, structurally efficient primary aircraft structures. As part of the Advanced Composite Technology (ACT) program to exploit this potential for heavily loaded aircraft structures, the design and fabrication of the technology integration box beam (TIBB) was completed. The TIBB is an advanced composite prototype structure for the center wing section of the Lockheed C-130 aircraft. The TIBB was tested for downbending, upbending, torsion, and combined upbending and torsion load conditions to verify the design. The TIBB failed at 83 percent of design ultimate load for the combined upbending and torsion load condition. Current analytical and experimental results are described for a study of the mechanisms that led to the failure of the TIBB. Experimental results include load, strain, and deflection data. An analytical study was conducted of the TIBB structural response. Analytical results include strain and deflection results from a global analysis of the TIBB.

Shuart, Mark J.↗
NASA NTRS1992

High-performance equation solvers and their impact on finite element analysis

The role of equation solvers in modern structural analysis software is described. Direct and iterative equation solvers which exploit vectorization on modern high-performance computer systems are described and compared. The direct solvers are two Cholesky factorization methods. The first method utilizes a novel variable-band data storage format to achieve very high computation rates and the second method uses a sparse data storage format designed to reduce the number od operations. The iterative solvers are preconditioned conjugate gradient methods. Two different preconditioners are included; the first uses a diagonal matrix storage scheme to achieve high computation rates and the second requires a sparse data storage scheme and converges to the solution in fewer iterations that the first. The impact of using all of the equation solvers in a common structural analysis software system is demonstrated by solving several representative structural analysis problems.

Poole, Eugene L.↗
NASA NTRS1992

Coupled 2D-3D finite element method for analysis of a skin panel with a discontinuous stiffener

This paper describes a computationally efficient analysis method which was used to predict detailed stress states in a typical composite compression panel with a discontinuous hat stiffener. A global-local approach was used. The global model incorporated both 2D shell and 3D brick elements connected by newly developed transition elements. Most of the panel was modeled with 2D elements, while 3D elements were employed to model the stiffener flange and the adjacent skin. Both linear and geometrically nonlinear analyses were performed on the global model. The effect of geometric nonlinearity induced by the eccentric load path due to the discontinuous hat stiffener was significant. The local model used a fine mesh of 3D brick elements to model the region at the end of the stiffener. Boundary conditions of the local 3D model were obtained by spline interpolation of the nodal displacements from the global analysis. Detailed in-plane and through-the-thickness stresses were calculated in the flange-skin interface near the end of the stiffener.

Wang, J. T.↗
NASA NTRS1991

Detailed analysis and test correlation of a stiffened composite wing panel

New finite element analysis methods are examined by application to a complicated composite wing panel from the V-22 rotorcraft. A detailed FEM model with a relatively coarse mesh of 9-node elements was generated, and linear and nonlinear stress analyses, first-ply failure analyses, and buckling analyses were conducted. At low values of applied load, i.e., up to the design ultimate load of the panel, the linear stress analysis accurately predicted the strains and structural response characteristics of the panel.

Davis, D. D., Jr.↗
NASA NTRS1991

An accurate nonlinear finite element analysis and test correlation of a stiffened composite wing panel

State-of-the-art nonlinear finite element analysis techniques are evaluated by applying them to a realistic aircraft structural component. A wing panel from the V-22 tiltrotor aircraft is chosen because it is a typical modern aircraft structural component for which there is experimental data for comparison of results. From blueprints and drawings, a very detailed finite element model containing 2284 9-node Assumed Natural-Coordinate Strain elements was generated. A novel solution strategy which accounts for geometric nonlinearity through the use of corotating element reference frames and nonlinear strain-displacement relations is used to analyze this detailed model. Results from linear analyses using the same finite element model are presented in order to illustrate the advantages and costs of the nonlinear analysis as compared with the more traditional linear analysis.

Davis, D. D., Jr.↗
NASA NTRS1962

Magnetically Diffused Radial Electric-Arc Air Heater Employing Water-Cooled Copper Electrodes

A magnetically rotated electric-arc air heater has been developed that is novel in that an intense magnetic field of the order of 10,000 to 25,000 gauss is employed. This field is supplied by a coil that is connected in series with the arc. Experimentation with this heater has shown that the presence of an intense magnetic field transverse to the arc results in diffusion of the arc and that the arc has a positive effective resistance. With the field coil in series with the arc, highly stable arc operation is obtained from a battery power supply. External ballast is not required to stabilize the arc when it is operating at maximum power level. The electrode erosion rate is so low that the airstream contamination is no more than 0.07 percent and may be substantially less.

COPPER↗