Engineering topics

Davis, M. W.

Publications and source records attributed to Davis, M. W..

7 records

NASA NTRS2018

Bar Code Events in the Juno-UVS Data: Signature ~10 MeV Electron Microbursts at Jupiter

One of the most intriguing discoveries of Juno is the quasi-systematic detection of upgoing electrons above the auroral regions. Here we discuss a by-product of the most energetic component of this population: a contamination resembling bar codes in the Juno-UVS images. This pattern is likely caused by bursts of ∼10 MeV electrons penetrating the instrument. These events are mostly detected when Juno’s magnetic footprint is located poleward of the main emission relative to the magnetic pole. The signal is not periodic, but the bursts are typically 0.1–1 s apart. They are essentially detected when Juno-UVS is oriented toward Jupiter, indicating that the signal is due to upgoing electrons. The event detections occur between 1 and 7 Jovian radii above the 1-bar level, suggesting that the electron acceleration takes place close to Jupiter and is thus both strong and brief.

Microbursts↗

NASA NTRS1985

Analysis of potential helicopter vibration reduction concepts

Results of analytical investigations to develop, understand, and evaluate potential helicopter vibration reduction concepts are presented in the following areas: identification of the fundamental sources of vibratory loads, blade design for low vibration, application of design optimization techniques, active higher harmonic control, blade appended aeromechanical devices, and the prediction of vibratory airloads. Primary sources of vibration are identified for a selected four-bladed articulated rotor operating in high speed level flight. The application of analytical design procedures and optimization techniques are shown to have the potential for establishing reduced vibration blade designs through variations in blade mass and stiffness distributions, and chordwise center-of-gravity location.

Landgrebe, A. J.↗

NASA NTRS1985

Adaptation of a modern medium helicopter (Sikorsky S-76) to higher harmonic control

Sikorsky Aircraft has performed analytical studies, design analyses, and risk reduction tests have been performed for Higher Harmonic Control (HHC) on the S-76. The S-76 is an 8 to 10,000 lb helicopter which cruises at 145 kts. Flight test hardware has been assembled, main servo frequency response tested and upgraded, aircraft control system shake tested and verified, open loop controllers designed and fabricated, closed loop controllers defined and evaluated, and rotors turning ground and flight tests planned for the near future. Open loop analysis shows that about 2 deg of higher harmonic feathering at the blade 75% radius will be required to eliminate 4P vibration in the cockpit.

Oleary, J. J.↗

NASA NTRS1984

Refinement and evaluation of helicopter real-time self-adaptive active vibration controller algorithms

A Real-Time Self-Adaptive (RTSA) active vibration controller was used as the framework in developing a computer program for a generic controller that can be used to alleviate helicopter vibration. Based upon on-line identification of system parameters, the generic controller minimizes vibration in the fuselage by closed-loop implementation of higher harmonic control in the main rotor system. The new generic controller incorporates a set of improved algorithms that gives the capability to readily define many different configurations by selecting one of three different controller types (deterministic, cautious, and dual), one of two linear system models (local and global), and one or more of several methods of applying limits on control inputs (external and/or internal limits on higher harmonic pitch amplitude and rate). A helicopter rotor simulation analysis was used to evaluate the algorithms associated with the alternative controller types as applied to the four-bladed H-34 rotor mounted on the NASA Ames Rotor Test Apparatus (RTA) which represents the fuselage. After proper tuning all three controllers provide more effective vibration reduction and converge more quickly and smoothly with smaller control inputs than the initial RTSA controller (deterministic with external pitch-rate limiting). It is demonstrated that internal limiting of the control inputs a significantly improves the overall performance of the deterministic controller.

Davis, M. W.↗

NASA NTRS1984

Development and evaluation of a generic active helicopter vibration controller

A computerized generic active controller is developed, which alleviates helicopter vibration by closed-loop implementation of higher harmonic control (HHC). In the system, the higher harmonic blade pitch is input through a standard helicopter swashplate; for a four-blade helicopter rotor the 4/rev vibration in the rotorcraft is minimized by inducing cyclic pitch motions at 3, 4, and 5/rev in the rotating system. The controller employs the deterministic, cautious, and dual control approaches and two linear system models (local and global), as well as several methods of limiting control. Based on model testing, performed at moderate to high values of forward velocity and rotor thrust, reductions in the rotor test apparatus vibration from 75 to 95 percent are predicted, with HHC pitch amplitudes of less than one degree. Good performance is also noted for short-duration maneuvers.

Davis, M. W.↗

NASA NTRS1984

Analysis of potential helicopter vibration reduction concepts

Several recent helicopter vibration reduction research programs are described. Results of studies of blade design parameters in rotor vibratory response and of an advanced blade design for reduced vibration are examined. An optimization approach to develop a general automated procedure for rotor blade design is described, and analytical results for an articulated rotor operating at a steady 160 kt flight condition are reported. The use of a self-adaptive controller to implement higher harmonic control in closed-loop fashion is addressed, and a computer simulation used to evaluate and compare the performance of alternative algorithms included in the generic active controller is discussed. Results are presented for steady level flight conditions, short-duration maneuvers, blade stresses and rotor performance, blade-appended aeroelastic devices, vibratory airloads, wake-induced blade airloads, and airloads from blade motions, the interaction of rotor and fuselage, and the interaction of rotor and empennage.

Landgrebe, A. J.↗

NASA NTRS1984

Optimization of helicopter rotor blade design for minimum vibration

The optimization approach discussed is part of an ongoing effort to develop a general automated procedure for rotor blade design. This procedure can be used to determine the necessary geometric, structural, and material properties of a rotor system to achieve desired objectives relating to vibration, stress, and aerodynamic performance. The approach used for helicopter vibration is emphasized. Based on analytical studies performed at the United Technologies Research Center (UTRC), a simplified vibration analysis was developed to be used in conjunction with a forced response analysis in the optimization process. This simplified analysis improves the efficiency of the design process significantly. Results of applying this approach to the design of an existing rotor blade model are presented.

Davis, M. W.↗