Search NASA⌕ Search

Engineering topics

Daw, C Stuart

Publications and source records attributed to Daw, C Stuart.

At least 37 records · Page 2

Cold-Start Emissions Control in Hybrid Vehicles Equipped with a Passive Hydrocarbon and NOx Adsorber

We presents a study of the potential for using low-cost sorbent materials (i.e. Ag-Beta-zeolite and Fe-Mn-Zr transition metal oxides) to temporally trap hydrocarbons (HCs) and nitrogen oxides (NOx) emissions during cold-start periods in HEVs and PHEVs over transient driving cycles. The adsorption behavior of the candidate sorbent materials was characterized in our laboratory flow reactor experiments. The parameters were then used to develop a one-dimensional, transient device model which has been implemented in the Powertrain Systems Analysis Toolkit (PSAT) to simulate a passive HC and NOx absorber device. The results show that such an absorber can substantially reduce HC and NOx emissions by storing them when the 3-way catalyst is too cool to function and re-releasing them when the exhaust temperature rises. These improved emission controls do not involve any penalty in fuel consumption or require any change in engine operation. The cost of these sorbent materials is also much less than conventional 3-way catalysts.

42 ENGINEERING↗

Simulation of catalytic oxidation and selective catalytic NOx reduction in lean-exhaust hybrid vehicles

We utilize physically-based models for diesel exhaust catalytic oxidation and urea-based selective catalytic NOx reduction to study their impact on drive cycle performance of hypothetical light-duty diesel powered hybrid vehicles. The models have been implemented as highly flexible SIMULINK block modules that can be used to study multiple engine-aftertreatment system configurations. The parameters of the NOx reduction model have been adjusted to reflect the characteristics of Cu-zeolite catalysts, which are of widespread current interest. We demonstrate application of these models using the Powertrain System Analysis Toolkit (PSAT) software for vehicle simulations, along with a previously published methodology that accounts for emissions and temperature transients in the engine exhaust. Our results illustrate the potential impact of DOC and SCR interactions for lean hybrid electric and plug-in hybrid electric vehicles.

33 ADVANCED PROPULSION SYSTEMS↗

Simulating Study of Premixed Charge Compression Ignition on Light-Duty Diesel Fuel Economy and Emissions Control

We utilize the Powertrain Systems Analysis Toolkit (PSAT) combined with transient engine and aftertreatment component models to simulate the impact of premixed charge compression ignition (PCCI) on the fuel economy and emissions of light-duty (LD) diesel-powered conventional and hybrid electric vehicles (HEVs). Our simulated aftertreatment train consists of a diesel oxidation catalyst (DOC), lean NOx trap (LNT), and catalyzed diesel particulate filter (DPF). The results indicate that utilizing PCCI combustion significantly reduces fuel consumption and tailpipe emissions for the conventional diesel-powered vehicle with NOx and particulate emissions controls. These benefits result from a favorable engine speed-load distribution over the cycle combined with a corresponding reduction in the need to regenerate the LNT and DPF. However, the current PCCI technology appears to offer less potential benefit for diesel HEVs equipped with similar emissions controls. This is because PCCI can only be activated over a relatively small part of the drive cycle. Thus we conclude that future utilization of PCCI in diesel HEVs will require significant extension of the available speed-load range for PCCI and revision of current HEV engine management strategies before significant benefits can be realized.

33 ADVANCED PROPULSION SYSTEMS↗

Spatiotemporal distribution of NOx storage and impact on NH3 and N2O selectivities during lean/rich cycling of a Ba-based lean NOx trap catalyst

We summarize results from an investigation of the spatiotemporal distribution of NO{sub x} storage and intermediate gas species in determining the performance of a fully formulated, Ba-based, lean NO{sub x} trap catalyst under lean/rich cycling conditions. By experimentally resolving spatiotemporal profiles of gas composition, we found that stored NO{sub x} was significantly redistributed along the monolith axis during the rich phase of the cycle by release and subsequent downstream re-adsorption. Sulfur poisoning of upstream NO{sub x} storage sites caused the active NO{sub x}-storage zone to be displaced downstream. This axial displacement in turn influenced rich-phase NO{sub x} release and re-adsorption. As sulfur poisoning increased, NH3 slip at the catalyst exit also increased due to its formation closer to the catalyst outlet and decreased exposure to downstream oxidation by surface oxygen. N{sub 2}O formation was found to be associated with nitrate reduction rather than oxidation of NH3 by stored oxygen. We propose that the observed evolution of N{sub 2}O selectivity with sulfation can be explained by changes in the spatiotemporal distribution of NO{sub x} storage resulting in either increased or decreased number of precious-metal sites surrounded by nitrates.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Microkinetic modeling of lean NOx trap chemistry

A microkinetic chemical reaction mechanism capable of describing both the storage and regeneration processes in a fully formulated lean NO{sub x} trap is presented. The mechanism includes steps occurring on the precious metal, NO{sub x} storage, and oxygen storage sites of the catalyst. The complete reaction set is used with a transient plug flow reactor code (including boundary layer mass transfer) to simulate not only storage/regeneration cycles with a CO/H{sub 2} reductant, but also steady flow temperature sweep experiments that were previously analyzed with just a precious metal mechanism and a simpler steady state code. The results imply that NO{sub x} storage was not negligible during some of the temperature ramps, necessitating a re-evaluation of the precious metal kinetic parameters. The parameters for the entire mechanism are inferred by finding the best overall fit to the complete set of experiments. Rigorous thermodynamic consistency is enforced for parallel reaction pathways and with respect to known data for all gas phase species. It is found that nearly all of the basic experimental observations can be reproduced with the transient simulations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

An Analysis of the Impact of Selected Fuel Thermochemical Properties on Internal Combustion Engine Efficiency

In this study we model the effects of 23 different fuels on First and Second Law thermodynamic efficiency of an adiabatic internal combustion engine. First Law efficiency is calculated using lower heating value (LHV) while Second Law efficiency is calculated with exergy, which represents the inherent chemical energy available to produce propulsion. We find that First Law efficiency can deviate by as much as nine percentage points between fuels while Second Law efficiency exhibits a much smaller degree of variability. We also find that First and Second Law efficiency can be nearly the same for some fuels (methane and ethane) but differ substantially for other fuels (hydrogen and ethanol). The differences in First and Second Law efficiency are due to differences in LHV and exergy for a given fuel. In order to explain First Law efficiency differences between fuels as well as the differences between LHV and exergy, we introduce a new term: the molar expansion ratio (MER), defined as the ratio of product moles to reactant moles for complete stoichiometric combustion. We find that the MER is a useful expression for providing a physical explanation for fuel-specific efficiency differences as well as differences between First and Second Law efficiency. First and Second Law efficiency are affected by a number of other fuel-specific thermochemical properties, such as the ratio of specific heat and dissociation of combustion products.

03 NATURAL GAS↗

Forensics of Soot: Nanostructure as a Diagnostic of In-Cylinder Chemistry

We report observations of changes in the microstructure of soot from an experimental light-duty diesel engine, produced with varying levels of biodiesel fuel blending. Based on these changes, we propose a hypothesis for how these changes relate to in-cylinder combustion chemistry. Our hypothesis centers on the assumption that fullerenic lamellar structures in soot trace their origin to 5-membered rings (C5s) formed early in the combustion process from gas-phase reaction intermediates. We also speculate that fullerenic microstructures may be a general feature of soot produced with oxygenated fuels and might be useful for diagnosing important changes in combustion trajectories.

33 ADVANCED PROPULSION SYSTEMS↗

Simulation of lean NOx trap performance with microkinetic chemistry and without mass transfer.

A microkinetic chemical reaction mechanism capable of describing both the storage and regeneration processes in a fully formulated lean NO{sub x} trap (LNT) is presented. The mechanism includes steps occurring on the precious metal, barium oxide (NO{sub x} storage), and cerium oxide (oxygen storage) sites of the catalyst. The complete reaction set is used in conjunction with a transient plug flow reactor code to simulate not only conventional storage/regeneration cycles with a CO/H{sub 2} reductant, but also steady flow temperature sweep experiments that were previously analyzed with just a precious metal mechanism and a steady state code. The results show that NO{sub x} storage is not negligible during some of the temperature ramps, necessitating a re-evaluation of the precious metal kinetic parameters. The parameters for the entire mechanism are inferred by finding the best overall fit to the complete set of experiments. Rigorous thermodynamic consistency is enforced for parallel reaction pathways and with respect to known data for all of the gas phase species involved. It is found that, with a few minor exceptions, all of the basic experimental observations can be reproduced with these purely kinetic simulations, i.e., without including mass-transfer limitations. In addition to accounting for normal cycling behavior, the final mechanism should provide a starting point for the description of further LNT phenomena such as desulfation and the role of alternative reductants.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Simulated comparisons of emissions and fuel efficiency of diesel and gasoline hybrid electric vehicles

This paper presents details and results of hybrid and plug-in hybrid electric passenger vehicle (HEV and PHEV) simulations that account for the interaction of thermal transients from drive cycle demands and engine start/stop events with aftertreatment devices and their associated fuel penalties. The simulations were conducted using the Powertrain Systems Analysis Toolkit (PSAT) software developed by Argonne National Laboratory (ANL) combined with aftertreatment component models developed at Oak Ridge National Lab (ORNL). A three-way catalyst model is used in simulations of gasoline powered vehicles while a lean NOx trap model in used to simulated NOx reduction in diesel powered vehicles. Both cases also use a previously reported methodology for simulating the temperature and species transients associated with the intermittent engine operation and typical drive cycle transients which are a significant departure from the usual experimental steady-state engine-map based approach adopted often in vehicle system simulations. Comparative simulations indicate a higher efficiency for diesel powered vehicles but the advantage is lowered by about a third (for both HEVs and PHEVs) when the fuel penalty associated with operating a lean NOx trap is included and may be reduced even more when fuel penalty associated with a particulate filter is included in diesel vehicle simulations. Through these preliminary studies, it is clearly demonstrated how accurate engine and exhaust systems models that can account for highly intermittent and transient engine operation in hybrid vehicles can be used to account for impact of emissions in comparative vehicle systems studies. Future plans with models for other devices such as particulate filters, diesel oxidation and selective reduction catalysts are also discussed.

02 PETROLEUM↗

Using a Phenomenological Computer Model to Investigate Advanced Combustion Trajectories in a CIDI Engine

This paper summarizes results from simulations of conventional, high-dilution, and high-efficiency cleancombustion in a diesel engine based on a two-zone phenomenological model. The two-zone combustionmodel is derived from a previously published multi-zone model, but it has been further simplified toincrease computational speed by a factor of over 100. The results demonstrate that this simplified modelis still able to track key aspects of the combustion trajectory responsible for NOx and soot production. Inparticular, the two-zone model in combination with highly simplified global kinetics correctly predictsthe importance of including oxygen mass fraction (in addition to equivalence ratio and temperature)in lowering emissions from high-efficiency clean combustion. The methodology also provides a convenient framework for extracting information directly from in-cylinder pressure measurements. This feature is likely to be useful for on-board combustion diagnostics and controls. Because of the possibilityfor simulating large numbers of engine cycles in a short time, models of this type can provide insight into multi-cycle and transient combustion behavior not readily accessible to more computationally intensive models. Also the representation of the combustion trajectory in 3D space corresponding to equivalence ratio, flame temperature, and oxygen fraction provides new insight into optimal combustionmanagement.

33 ADVANCED PROPULSION SYSTEMS↗

Analysis of Combustion Trajectories of Advanced Combustion Modes in a CIDI Engine with a Two-Zone Phenomenological Model

We describe a two-zone phenomenological model for simulating in-cylinder details in conventional, highdilution, and high-efficiency clean combustion in a diesel engine. Using this model we characterize the differences in these combustion modes in terms of 3D trajectories involving equivalence ratio, flametemperature, and oxygen mass fraction. These trajectories in turn make it possible to better understand the relative NOx and particulate emissions of the different modes. The two-zone model predictions are shown to be consistent with more detailed CFD simulations and provide the benefit of very rapid simulation.

33 ADVANCED PROPULSION SYSTEMS↗

Characteristics of cyclic heat release variability in the transition from spark ignition to HCCI in a gasoline engine

We study selected examples of previously published cyclic heat-release measurements from a single-cylinder gasoline engine as stepwise valve timing adjustments were made to shift from spark ignited (SI) combustion to homogeneous charge compression ignition (HCCI). Wavelet analysis of the time series, combined with conventional statistics and multifractal analysis, revealed previously undocumented features in the combustion variability as the shift occurred. In the spark-ignition combustion mode, the heat-release variations were very small in amplitude and exhibited more persistent low-frequency oscillations with intermittent high-frequency bursts. In the HCCI combustion mode, the amplitude of the heat-release variations again was small and involved mainly low-frequency oscillations. At intermediate states between SI and HCCI, a wide range of very large-amplitude oscillations occurred, including both persistent low-frequency periodicities and intermittent high-frequency bursts. It appears from these results that real-time wavelet decomposition of engine cylinder pressure measurements may be useful for on-board tracking of SI HCCI combustion regime shifts.

33 ADVANCED PROPULSION SYSTEMS↗

A thermodynamic analysis of alternative approaches to chemical looping combustion

In this article, we review and clarify some of the points made by previous authors regarding chemical looping combustion (CLC). While much of the recent interest in chemical looping combustion has been associated with carbon sequestration, our primary interest here is its potential to increase the thermodynamic efficiency of converting fuel chemical energy into useful work. We expand on several points about the details of CLC that we feel have not previously been sufficiently explored, and suggest alternative (and possibly more practical) approaches that exploit some of the same thermodynamic concepts. We illustrate our key points with {First} and {Second} Law analyses of ideal conceptual processes, which in addition to {CLC} also include isothermal, non-equilibrium, preheated combustion and combustion with thermochemical recuperation. Our results suggest that a significant portion of the potential efficiency benefit of CLC might be achieved without the need to handle and transport large quantities of solid oxygen storage material. Exploitation of this fact may lead to higher efficiency approaches for power generation from hydrocarbon fuels combustion.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Impact of Biodiesel on the Oxidation Kinetics and Morphology of Diesel Particulate

We compare the oxidation characteristics of four different diesel particulates generated with a modern light-duty engine. The four particulates represent engine fueling with conventional ultra-low sulfur diesel (ULSD), biodiesel, and two intermediate blends of these fuels. The comparisons discussed here are based on complementary measurements implemented in a laboratory micro-reactor, including temperature programmed desorption and oxidation, pulsed isothermal oxidation, and BET surface area. From these measurements we have derived models that are consistent with the observed oxidation reactivity differences. When accessible surface area effects are properly accounted for, the oxidation kinetics of the fixed carbon components were found to consistently exhibit an Arrhenius activation energy of 113 6 kJ/mol. Release of volatile carbon from the as-collected particulate appears to follow a temperaturedependent rate law.

09 BIOMASS FUELS↗

Dynamic instabilities in spark-ignited combustion engines with high exhaust gas recirculation

We propose a cycle-resolved dynamic model for combustion instabilities in spark-ignition engines operating with high levels of exhaust gas recirculation (EGR). High EGR is important for increasing fuel efficiency and implementing advanced low-emission combustion modes such as homogenous charge compression ignition (HCCI). We account for the complex combustion response to cycle-to-cycle feedback by utilizing a global probability distribution that describes the pre-spark state of in-cylinder fuel mixing. The proposed model does a good job of simulating combustion instabilities observed in both lean-fueling engine experiments and in experiments where nitrogen dilution is used to simulate some of the combustion inhibition of EGR. When used to simulate high internal EGR operation, the model exhibits a range of global bifurcations and chaos that appear to be very robust. We use the model to show that it should be possible to reduce high EGR combustion instabilities by switching from internal to external EGR. We also explain why it might be helpful to deliberately stratify the fuel in the pre-spark gas mixture. It might be possible to extend the simple approach used in this model to other chemical reaction systems with spatial inhomogeneity.

33 ADVANCED PROPULSION SYSTEMS↗

Summary Report on the Transportation Combustion Engine Efficiency Colloquium Held at USCAR, March 3 and 4, 2010

This report summarizes results from an invited two-day colloquium of twenty-nine combustion engine experts from academia, industry, and national labs that was convened March 3rd and 4th, 2010, at the headquarters of the United States Council for Automotive Research (USCAR) in Southfield, Michigan. The colloquium was held at the request of The Department of Energy (DOE) Office of Freedom Car and Vehicle Technologies (OFCVT) to review and assess the current state of transportation combustion engine technology from theoretical and practical perspectives. In the ensuing discussions, the experts were able to reach a broad consensus on some important questions regarding current fuel efficiency limits. They also identified technology barriers and recommended specific near and longer-term R&D priorities for DOE's consideration. Internal combustion engines currently play a dominant role in U.S. transportation and are expected to continue to do so well beyond 2020 [1]. Because of this, the Department of Energy (DOE) has placed high priority on promoting technologies that maximize combustion engine fuel efficiency while minimizing greenhouse gas emissions. Identification of the most promising paths to achieve these goals has recently become more complicated as non-traditional transportation fuels and hybrid electric vehicles become widely available. To reassess the state of combustion engine science and identify new opportunities for technology breakthroughs, an invited colloquium of combustion engine experts was convened on March 3rd and 4th, 2010, at the headquarters of the United States Council for Automotive Research (USCAR) in Southfield, Michigan. The colloquium objectives were: (1) Review and assess the current state of transportation combustion engine technology from both theoretical and practical perspectives; (2) Arrive at a consensus on the theoretical and practical fuel efficiencies that can be achieved; and (3) Recommend near and longer-term R&D priorities for DOE to consider in developing their strategic planning for reaching efficiency goals. This report summarizes the main discussion points and recommendations that emerged from the meeting. Included are areas where there is widespread consensus and areas where there are still important technical uncertainties and wide ranging opinions.

33 ADVANCED PROPULSION SYSTEMS↗

Lean NOx Trap Modeling in Vehicle Systems Simulations

A one-dimensional model for simulating lean NOx trap (LNT) performance is developed and validated using both steady state cycling data and transient data from FTP testing cycles. The model consists of the conservation equations for chemical species and energy in the bulk flow, energy of the solid walls, O2 storage and NOx storage (in the form of nitrites and nitrates). Nitrites and nitrates are formed by diffusion of NO and NO2, respectively, into sorbent particles (assumed to be hemi-spherical in shape) along with O2 and their formation rates are controlled by chemical kinetics as well as solid-phase diffusion rates of NOx species. The model also accounts for thermal aging and sulfation of LNTs. Empirical correlations are developed on the basis of published experimental data to capture these effects. These empirical correlations depend on total mileage for which the LNT has been in use, the mileage accumulated since the last desulfation event in addition to the freshly degreened catalyst characteristics. The model has been used in studies of vehicle systems (integration, performance etc.) including hybrid powertrain configurations. Since the engines in hybrid vehicles turn on and off multiple number of times during single drive cycles, the exhaust systems may encounter multiple cold start transients. Accurate modeling of catalyst warm-up and cooling is, therefore, very important to simulate LNT performance in such vehicles. For this purpose, the convective heat loss from the LNT to the ambient is modeled using a Nusselt number correlation that includes effects of both forced convection and natural convection (with later being important when vehicle is stationary). Using the model, the fuel penalty associated with operating LNTs on small diesel engine powered car during FTP drive cycles is estimated.

33 ADVANCED PROPULSION SYSTEMS↗

A proposed methodology for estimating transient engine-out temperature and emissions from steady-state maps

Many vehicle systems simulations utilize engine maps constructed from steady-state dynamometer measurements to estimate exhaust temperature and emissions as functions of engine speed and load. Unfortunately, steady-state engine behavior is often significantly different from actual behavior under realistic driving conditions. This is particularly true for vehicles (e.g., electric hybrids) that undergo repeated engine shutdown and restart. We propose a methodology for estimating transient engine exhaust properties based on corrections to steady-state maps. We have implemented our methodology in the Powertrain Systems Analysis Toolkit (PSAT) and use this implementation to demonstrate good agreement with experimental measurements for both a light-duty diesel and a flex-fuel gasoline/ethanol engine. We also recommend specific procedures for setting key parameters required by our methodology and suggest possible directions for further improvements.

33 ADVANCED PROPULSION SYSTEMS↗