Search NASA⌕ Search

Engineering topics

Day, Robert D

Publications and source records attributed to Day, Robert D.

Production and measurement of engineered surfaces for inertial confinement fusion research

Inertial Confinement Fusion uses the optical energy from a very high power laser to implode spherical capsules that contain a fuel mixture of deuterium and tritium. The capsules are made of either Beryllium, plastic, or glass and range from 0.1 mm to 2 mm in diameter. As a capsule implodes, thereby compressing the fuel to reach nuclear fusion conditions, it achieves temperatures of millions of degrees Centigrade and very high pressures. In this state, the capsule materials act like fluids and often a low density fluidic material will push on a higher density material which can be a very unstable condition depending upon the smoothness of the interface between the two materials. This unstable condition is called a hydrodynamic instabillity which results in the mixing of the two materials. If the mixing occurs between the fuel and a non-fuel material, it can stop the fusion reaction just like adding significant amounts of water to gasoline can stop the operation of an automobile. Another region in the capsule where surface roughness can cause capsule performance degradation is at a joint. For instance, many capsules are made of hemispheres that are joined together. If the joint surfaces are too rough, then there will an effective reduction in density at the joint. This density reduction can cause a non-uniform implosion which will reduce the fusion energy coming out of the capsule.

02 PETROLEUM↗

Design of the neutron imaging pinhole for use at the national ignition facility

The Neutron Imaging (NI) diagnostic is designed to be used at the National Ignition Facility (NIF). This instrument will be used to image both primary (14MeV neutrons) and down scattered (6-8MeV neutrons). The pinhole body sits 225mm from the target, while the scintillator and recording systems are located 28m from the target. The diagnostic uses port 90, 315 and the recording system is located in a specifically built room located outside of switchyard I. The location of the pinhole and the recording system combine to give a magnification of 104. The recording of both the primary and downscattered image is done by recording the image from both the front and back side of the scintillator.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Improvements in ICF target fabrication through high precision assembly and nondestructive characterization

Current ICF and HED targets are fielded on Omega, Z, and Trident, and future campaigns will be fielded on NIF. NIF will only field less than 2 shots per day. With such few experiments, target fabrication and target alignment accuracy, enhanced metrology and advanced component machining will be even more important. Future target designs are also becoming more complex and more stringent in terms of accuracy. Several steps have been taken to improve the fabrication and characterization of targets, such as instituting an automated assembly station with 3 mm tolerances, utilizing nondestructive characterization tools for rapid component metrology and target assembly, and advancing machining capabilities. Recapitalization of target fabrication infrastructure is continuous.

36 MATERIALS SCIENCE↗

The National Ignition Facility Neutron Imaging System

The National Ignition Facility (NIF) is scheduled to begin deuterium-tritium (DT) shots possibly in the next several years. One of the important diagnostics in understanding capsule behavior and to guide changes in Hohlraum illumination, capsule design, and geometry will be neutron imaging of both the primary 14 MeV neutrons and the lower-energy downscattered neutrons in the 6-13 MeV range. The neutron imaging system (NIS) described here, which we are currently building for use on NIF, uses a precisely aligned set of apertures near the target to form the neutron images on a segmented scintillator. The images are recorded on a gated, intensified charge coupled device. Although the aperture set may be as close as 20 cm to the target, the imaging camera system will be located at a distance of 28 m from the target. At 28 m the camera system is outside the NIF building. Because of the distance and shielding, the imager will be able to obtain images with little background noise. The imager will be capable of imaging downscattered neutrons from failed capsules with yields Y{sub n}>10{sup 14} neutrons. The shielding will also permit the NIS to function at neutron yields >10{sup 18}, which is in contrast to most other diagnostics that may not work at high neutron yields. The following describes the current NIF NIS design and compares the predicted performance with the NIF specifications that must be satisfied to generate images that can be interpreted to understand results of a particular shot. The current design, including the aperture, scintillator, camera system, and reconstruction methods, is briefly described. System modeling of the existing Omega NIS and comparison with the Omega data that guided the NIF design based on our Omega results is described. We will show NIS model calculations of the expected NIF images based on component evaluations at Omega. We will also compare the calculated NIF input images with those unfolded from the NIS images generated from our NIS numerical modeling code.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Non-traditional machining techniques

During the course of machining targets for various experiments it sometimes becomes necessary to adapt fixtures or machines, which are designed for one function, to another function. When adapting a machine or fixture is not adequate, it may be necessary to acquire a machine specifically designed to produce the component required. In addition to the above scenarios, the features of a component may dictate that multi-step machining processes are necessary to produce the component. This paper discusses the machining of four components where adaptation, specialized machine design, or multi-step processes were necessary to produce the components.

36 MATERIALS SCIENCE↗

Manufacturing complex silica aerogel target components

Aerogel is a material used in numerous components in High Energy Density Physics targets. In the past these components were molded into the proper shapes. Artifacts left in the parts from the molding process, such as contour irregularities from shrinkage and density gradients caused by the skin, have caused LANL to pursue machining as a way to make the components.

36 MATERIALS SCIENCE↗