Search NASA⌕ Search

Engineering topics

Day, Thomas H.

Publications and source records attributed to Day, Thomas H..

9 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Evaluation of the relative importance of preheat from hohlraum x rays and a radiative shock on a low-density foam

Indirectly driven shock-tube experiments were performed on the Omega Laser Facility to evaluate the relative importance of hohlraum x ray and radiative shock preheat sources on a low-density foam. X rays emitted from the hohlraum and a subsequent shock wave are channeled into a low-density foam sample, which contains a plastic preheat-witness disk placed downstream of the foam. Simultaneous radiographic measurements of the shock speed in the foam and the expansion rate of the witness disk due to preheat allow for the observation of effects from the hohlraum's low-energy and high-energy x-ray spectrum. Here we showed, from simulations, that low-energy x rays from the hohlraum are preferentially absorbed near the ablator surface (where the hohlraum and the shock tube meet), while higher-energy x rays largely pass through the ablator and foam and are volumetrically absorbed by the witness disk. Reproducing the experimentally measured shock speed and expansion of the witness disk simultaneously, we extracted the temperature evolution of preheated foam from the simulation and evaluated the relative importance of preheat sources on a low-density foam from hohlraum x-ray radiation and radiative shock. We found that radiation from the shock front was more effective at preheating the low-density foam than the high-energy x rays from the hohlraum. This shock-tube preheat experiment is important for understanding the results of the MARBLE experiments at the National Ignition Facility because initial conditions of foam-filled MARBLE capsules are sensitive to preheat.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Post-Shot Report for OMEGA Double Cylinders (CylDRT 22B)

The direct-drive double cylinder experimental platform is a high-energy-density (HED) science platform designed to image an imploding cylindrical target. The target consists of a directly-driven outer cylinder and a shock-and-collision driven inner cylinder. The purpose of this platform is to study hydrodynamic instability growth on the inner cylinder, the outer surface of which is classically Rayleigh-Taylor unstable during the acceleration phase. We present results from recent experiments at the OMEGA laser facility. These experiments were designed as a proof-of-principle for the platform, using the same cylinder exterior dimensions and direct-drive beam configuration as previous single cylinder experiments. In these experiments, three sets of targets were fielded: no machined perturbations (smooth), a sinusoidal mode-10 perturbation on the outer surface of the inner cylinder, and a mode-20 perturbation on the outer surface of the inner cylinder. The primary diagnostic was a gated x-ray framing camera which imaged the backlit inner cylinder on-axis for sixteen frames over a time window of 1 ns for each shot. A second side-lit radiograph captured one image per shot, diagnosing axial uniformity. In this report we include an overview of the results from both the backlighter and the sidelighter diagnostics. We discuss at length the experimental analysis process. Finally, we present the results of the smooth target implosion trajectory and compare them to post-shot simulations. We see favorable agreement between simulation and experiment.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Preshot Report for OMEGA Double Cylinders (CylDRT 22B)

The primary goals for the May 2022 shot day at OMEGA are to: image an imploding inner cylinder as proof-of-principle for double cylinder experiments, measure the growth of pre-seeded perturbations on the inner cylinder, and measure the axial non-uniformity of the implosion with a sidelighter that provides a transverse view of the target. We will compare these experimental results to xRAGE (2D-only) and FLASH (2D and 3D) radiation-hydrodynamics calculations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Experimental validation of shock propagation through a foam with engineered macro-pores

The engineered macro-pore foam provides a new way to study thermonuclear burn physics by utilizing capsules containing deuterated (D) foam and filling tritium (T) gas in the engineered macro-pores. The implosion of a thermonuclear capsule filled with an engineered macro-pore foam will be complex due to the interaction of a shock wave with the engineered macro-pores. It is our goal to quantify how substantially complex foam structures affect the shape of shock and bulk shock speed. A cylinder-shape shock tube experiment has been designed and performed at the Omega Laser Facility. In order to examine how a foam structure will affect shock propagation, we performed several tests varying (1) engineered macro-pore size, (2) average foam density, and (3) with/without neopentane (C 5 H 12 ) gas. X-ray radiographic data indicate that shock speed through engineered macro-pore foams depends strongly on average foam density and less on pore size. In this work, experimental shock propagation data helped guide two numerical simulation approaches: (1) a 2D simulation with homogenizing foams rather than explicitly simulating engineered macro-pores and (2) a 2D toroidal-pore approximation adopting a toroidal-tube geometry to model engineered macro-pores.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Preshot Report for the NIF DDCyl Campaign: H_Hyd_DDCyl_DRT_AAA/BBB/CCC

The first two cylinder shot days on the National Ignition Facility, allocated through the Discovery Science program, provided a successful demonstration of the cylinder platform on the NIF. Both of these shot days used cylinders that were nominally 3 times larger in radial dimension than cylinders fielded at the OMEGA laser facility, here referred to as scale-3 targets. In the first Discovery Science shot day, we demonstrated that Rayleigh-Taylor instability growth during the deceleration phase is scale-invariant between the scale-1 OMEGA experiments and similarly tailored scale-3 NIF experiments at the same convergence ratio of CR=initial radius/final radius=2.25. In the second Discovery Science shot day, we increased the convergence ratio by lowering the density of the central foam from 300 mg/cm 3 to roughly 40 mg/cm 3 with the same laser drive, resulting in a higher CR=5 at the time when the rebounding shock strikes the aluminum marker. We also greatly improved the imaging setup for the second shot day, resulting in much higher quality (greater signal-to-noise) radiographs of the implosion. This current shot day was awarded through the High Energy Density (HED) Council, following this demonstration of platform viability. It was originally scheduled for June 2020, but it was postponed several times due to the COVID-19 pandemic. It is currently scheduled for January 6, 2021. For this shot day, we will increase the radial dimension of the cylinder to four times the OMEGA-scale targets, and these will be referred to as scale-4 cylinders. Increasing the radial dimension of the target is advantageous as we push these targets to higher convergence ratio. By starting with an initially larger target, the target can push to a higher CR while maintaining the same final viewing area. Other than the larger radial dimension, the targets are very similar in design to the previous ones, consisting of an epoxy ablator, an embedded aluminum marker layer, and a low density central CH foam. These will also use a 40 mg/cm3 CH foam, reaching a CR~4.5 with the same laser energy (the added target mass reduces the final CR slightly). Note that this is NOT designed to be scale-invariant with the previous scale-1 OMEGA and scale-3 NIF shots. It was determined that the laser energy required to achieve a scale-invariant implosion was above the allowable optics damage limits (though achievable on the NIF) for these scale-4 targets.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Preshot Report for the NIF Discovery Science DDCyl Campaign: D_Hyd_DDCyl_DRT_DDD/EEE/FFF

The first Discovery Science shot day with the NIF DDCyl campaign demonstrated that Rayleigh-Taylor instability growth during the deceleration phase is scale-invariant for targets that varied in radial dimension and implosion time-scale by a factor of three. Smaller cylindrical implosions at the OMEGA laser facility were compared to the larger cylinders fielded in our first NIF outing. Both sets of targets had an initial m = 20 sinusoidal perturbation machined on the inner surface of an embedded aluminum marker layer, with the amplitude larger by the same factor of three for the NIF-scale targets. We observed growth factors of 14 at late time (t=λ = 7:7 ns, where λ = 1 for OMEGA and λ = 3 for NIF). These used a high density (300 mg/cm³) CH foam core, providing a very long period of deceleration before the rebounding shock hit the incoming spike tips, but the final convergence was only CR≈ 2:25. For our second shot day with this campaign, we are attempting to increase the convergence ratio to CR≥ 5 before reshock, while still measuring instability growth during the convergence/deceleration phase. As discussed in previous reports, the best way to increase convergence before reshock is to lower the density of the central foam. The preshot designs called for the use of a 30 mg/cm³ CH foam, though the as-built foams are closer to 40-42 mg/cm³, which is predicted to result in a final CR≈ 5:1 before reshock. Other than the lower foam density, the target design is identical to those used previously.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2020

Design of Cylindrical Implosion Experiments to Demonstrate Scale-Invariant Rayleigh-Taylor Instability Growth

Radiation-hydrodynamics simulations are used to design laser-driven cylindrical implosion experiments to directly measure hydrodynamic instability growth in convergent geometry. Designs for two different size targets, varying in radial dimension by a factor of three, are presented. A set of beam pointings and powers are identified for each scale design that result in a nearly axially uniform implosion of an embedded marker layer. The implosion trajectories are shown to be scale-invariant between designs, with nearly identical scaled acceleration profiles. Finally, linear theory and radiation-hydrodynamics simulations predict that Rayleigh-Taylor instability growth of an azimuthal perturbation, machined on the inner surface of the embedded marker, is also scale-invariant between designs.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2020

Demonstration of Scale-Invariant Rayleigh-Taylor Instability Growth in Laser-Driven Cylindrical Implosion Experiments

Rayleigh-Taylor instability growth is shown to be hydrodynamically scale-invariant in convergent cylindrical implosions for targets that varied in radial dimension and implosion timescale by a factor of three. The targets were driven directly by laser irradiation providing a short impulse, and instability growth at an embedded aluminum interface occurs as it converges radially inward by a factor of2.25 and decelerates on a central foam core. Late-time growth factors of 14 are observed for a single-modem= 20 azimuthal perturbation at both scales, despite the differences in laser drive conditions between the experimental facilities, consistent with predictions from radiation-hydrodynamics simulations. This platform enables detailed investigations into the limits of hydrodynamic scaling in high-energy-density systems.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗