Search NASA⌕ Search

Engineering topics

De Pascuale, Sebastian

Publications and source records attributed to De Pascuale, Sebastian.

6 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Evaluation of SPARC divertor conditions in H-mode operation using SOLPS-ITER

The predicted divertor conditions for the SPARC tokamak are calculated using SOLPS-ITER for a range of scrape-off-layer (SOL) heat flux widths λ q , input powers, and particle fueling locations. Under H-mode scenario conditions with an upstream separatrix density of 1 x 10 20 m -3 , the most conservative range of λ q extrapolations ( 0.15 mm) results in extremely high unmitigated particle and energy fluxes to the divertor, both under full field (12.2 T) and power (P SOL = 29 MW) conditions, and 2/3 field with P SOL = 10 MW. Increasing the cross-field SOL diffusivities by 2–10× reduces the magnitude of the mitigation challenge, however strategies such as impurity seeding or strike-point-sweeping will likely still be required. A combination of steady-state and time-dependent SOLPS-ITER simulations are used to map out phase space diagrams of upstream and divertor conditions. The simulations include parallel currents but neglect cross-field drifts. At low upstream density the inner and outer divertor conditions are highly asymmetric, with a large temperature difference and significant heat fluxes driven by parallel currents. The solution has sharp bifurcations with a region of hysteresis, depending on whether the initial state is at a low or high density. This behavior is observed even when the fueling location, cross-field diffusivity, and impurity level is changed, although the density window with asymmetry is reduced with increasing diffusivity. The addition of neon impurity seeding reduces the divertor heat fluxes, but also causes a drop in the upstream electron density with fixed particle throughput. This drop can be counteracted by increased main ion throughput, however too much neon results in a back transition into the asymmetric divertor regimes suggesting a need for control of both main ion and impurity seeding levels to achieve a desired divertor state.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Full time-dependent SOLPS-ITER simulation of the SPARC tokamak: actuator design for particle and divertor condition control *

Abstract This paper presents the application of full time-dependent SOLPS-ITER simulations for actuator design in the SPARC tokamak. This study employs both the EIRENE module, a neutral solver, and the B2.5 plasma module in a time-dependent mode. This is in contrast to most SOLPS simulations, which focus on steady-state solutions, where the neutral distribution is evolved without any time limit or for a time step of 1 ⋅ 10 − 3 second, which is several orders of magnitude larger than the fluid plasma time step. The time-dependent EIRENE was tested with a fixed B2.5 background and compared with a simple conductance based model in a simplified pump chamber geometry. This comparison aimed to verify the reliability of the neutral relaxation timescale derived from the time-dependent EIRENE. Subsequently, a full time-dependent simulation was performed in a realistic geometry, with the Monte-Carlo neutral time step synchronized with the plasma fluid time step. The numerical setup of the code, including relative time steps and the size of the census data used to store Monte-Carlo particle information is considered. The full-time dependent simulations are then applied to inform the design of the SPARC louver structure, which affects divertor plasma parameters by regulating the neutral conductance from the divertor to the pump. The response of the plasma and neutral parameters was captured on a timescale that enables the design of the actuator to consider time-dependent control capability. It was found that changing the louver opacity has an equivalent effect as varying the gas throughput via puff actuation. Therefore, equivalent divertor plasma conditions can be obtained from both actuators, while the neutral pressure distribution in the pump and divertor differs for each actuator.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Time-Dependent Boundary Modeling to Inform Design of SPARC Diagnostic and Actuators

The purpose of this work was to inform the design of diagnostic and actuator systems for a new experimental facility for Commonwealth Fusion Systems (CFS), called SPARC [Creely2020], using time-dependent plasma boundary simulations with the Scrape Off Layer Plasma Simulator (SOLPS) code [Wiesen2015]. The SPARC tokamak is a device that aims to demonstrate fusion energy production and high-field plasma operating scenarios. The developed technologies will be incorporated into a net-electricity pilot that will demonstrate approximately 200MW of electric power. A major difference from other private industry fusion companies is the use of a standard aspect ratio, but at a high magnetic field strength, which provides a well-established physics basis and a modest extrapolation to reactor operation. Time-dependent simulations were used to inform the design of main-chamber plasma facing components, which are protected by feedback control of the heat and particle loads during high power operation. The simulations provide the timescales and magnitudes of plasma and neutral particle response useful for determining the position and operation of diagnostics and actuators that will enable control. The plasma response and phase-space diagrams also provide input into advanced model-based control schemes, which are envisioned for later SPARC operation. Model-based control can reduce the risk of component failure, which would require expensive in-situ repairs and the associated delays, by predicting the system response to actuators over a short time-horizon.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Compression of tokamak boundary plasma simulation data using a maximum volume algorithm for matrix skeleton decomposition

This report demonstrates satisfactory data compression of SOLPS-ITER simulation output ranging from 2D fields, 1D profiles, and 0D scalar variables with a novel matrix decomposition approach. The singular value decomposition (SVD) scales poorly for large matrix sizes and is unsuited to the application on high dimensional data common to fusion plasma physics simulation. In this work, we employ the columns-submatrix-rows (CUR) matrix factorization technique in order to compute a low-rank approximation up to two orders of magnitude faster than the SVD, but within a nominal L2-norm relative error of ε = 10 –2 . In addition, the CUR approach maintains the original format of the data, in its extracted columns and rows, allowing for interpretable data storage at the original resolution of the simulation. We utilize an iterative algorithm to compute the CUR decomposition of simulation output by maximizing the volume, or linearly independent information content, of a low-rank submatrix contained within the data. Experiments over $\textit{n} × \textit{n}$ randomized test matrices with embedded rank-deficient features show that this maximum volume implementation of CUR matrix approximation has reduced asymptotic computational complexity on the order of n compared to the SVD, which scales approximately as $n^3$. These results show that the CUR technique can be used to effectively select time step snapshots (columns) of over 140 SOLPS-ITER output variables and the associated discretized coordinate timeseries (rows) allowing for reconstruction of the complete simulation dynamics.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS2016

Survey of the Frequency Dependent Latitudinal Distribution of the Fast Magnetosonic Wave Mode from Van Allen Probes Electric and Magnetic Field Instrument and Integrated Science Waveform Receiver Plasma Wave Analysis

We present a statistical survey of the latitudinal structure of the fast magnetosonic wave mode detected by the Van Allen Probes spanning the time interval of 21 September 2012 to 1 August 2014. We show that statistically, the latitudinal occurrence of the wave frequency (f) normalized by the local proton cyclotron frequency (f(sub cP)) has a distinct funnel-shaped appearance in latitude about the magnetic equator similar to that found in case studies. By comparing the observed E/B ratios with the model E/B ratio, using the observed plasma density and background magnetic field magnitude as input to the model E/B ratio, we show that this mode is consistent with the extra-ordinary (whistler) mode at wave normal angles (theta(sub k)) near 90 deg. Performing polarization analysis on synthetic waveforms composed from a superposition of extra-ordinary mode plane waves with theta(sub k) randomly chosen between 87 and 90 deg, we show that the uncertainty in the derived wave normal is substantially broadened, with a tail extending down to theta(sub k) of 60 deg, suggesting that another approach is necessary to estimate the true distribution of theta(sub k). We find that the histograms of the synthetically derived ellipticities and theta(sub k) are consistent with the observations of ellipticities and theta(sub k) derived using polarization analysis.We make estimates of the median equatorial theta(sub k) by comparing observed and model ray tracing frequency-dependent probability occurrence with latitude and give preliminary frequency dependent estimates of the equatorial theta(sub k) distribution around noon and 4 R(sub E), with the median of approximately 4 to 7 deg from 90 deg at f/f(sub cP) = 2 and dropping to approximately 0.5 deg from 90 deg at f/f(sub cP) = 30. The occurrence of waves in this mode peaks around noon near the equator at all radial distances, and we find that the overall intensity of these waves increases with AE*, similar to findings of other studies.

Boardsen, Scott A.↗