Search NASA⌕ Search

Engineering topics

DeHart, Mark

Publications and source records attributed to DeHart, Mark.

At least 19 records

Integrated Steady-State System Package for Nuclear Thermal Propulsion Analysis Using Multi-Dimensional Thermal Hydraulics and Dimensionless Turbopump Treatment

Nuclear thermal propulsion is an evolving technology that can be utilized for long-distance space travel. This technology yields the advantage of a high thrust and specific impulse, but requires an examination of the potential design adjustments necessary to enhance its feasibility. The development of nuclear thermal propulsion requires a comprehensive understanding of the system-level behavior during transient and steady-state operation. This paper extends our previous research by including the proper handling of turbomachinery with multi-channel thermal hydraulic simulations only for steady-state solutions. The system-level approach presented here enables the treatment of the turbopump components through non-dimensional analysis that eliminates the assumption of constant efficiencies. All the other components within the system (e.g., reflector and core) can be discretized to multiple channels and layers, in which the full thermal hydraulic solution is established. The approach chosen here enables the realistic modeling of the propellant flow within the expander cycle by capturing the pressure losses, mass flow rate splits, and enthalpy gain for various operational conditions. The verification of the package is completed through point comparisons of previous investigations into similar system designs. Furthermore, sensitivity studies are used to benchmark the capabilities of the package and investigate solution variations due to the perturbation of operational conditions and regimes. The sensitivity studies performed here are important to capture variation in flow characteristics (e.g., temperature, pressure, mass flow rates) for different design objectives such as the thrust and specific impulse. This work demonstrates that system-level simulations lacking multi-channel capability and proper turbomachinery treatment may yield higher uncertainties in understanding the engine’s response and characteristics to changing various requirements. This is extremely important when screening the design space of such propulsion systems and when transient simulations are required.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Engagement opportunities in OECD NEA benchmark development

A myriad of opportunities is available to collaborate via international benchmark exercises and experimental data preservation activities. Many such opportunities abound under the auspices of the Nuclear Science Committee of the Organisation for Economic Co-operation and Development Nuclear Energy Agency (NEA). Key projects and activities of relevance to the development of advanced reactors design include the International Criticality Safety Benchmark Evaluation Project (ICSBEP), the International Reactor Physics Experiment Evaluation Project (IRPhEP), the International Assay Data of Spent Nuclear Fuel Database (SFCOMPO), the Shielding Integral Benchmark and Archive Database (SINBAD), and The International Experimental Thermal HYdraulicS Database (TIETHYS), and various cooperative benchmark exercises. Interested participants are encouraged to contact the leadership and secretariat of the various Technical Working Groups and Working Parties to become more engaged. This paper provides a summary of the current benchmark exercises and experimental databases available for international participation.

96 KNOWLEDGE MANAGEMENT AND PRESERVATION↗

Initial exploration of a novel transient arrest system involving fuel heating

A preliminary analysis on a novel accident response system to diminish the severity of super- critical transients was conducted. The novel accident response system, called the instant shock arrest system, involves using electricity to heat the nuclear fuel at the onset of a large accidental reactivity insertion. This system is specifically designed for reactors with metallic fuel, such that the fuel is capable of conducting electricity, and being resistively heated. A reactor dynamics model of the advanced test reactor was created using the point kinetics equations and a linear reactivity feedback model to simulate how the system would effect the maximum fuel temperatures experienced during the transient. Transients with the instant shock arrest system were compared to those without it. It was found that the instant shock arrest system initially heated the fuel more than the unaffected transient but the negative reactivity inserted from such heating was enough to lower the maximum fuel temperature experienced during the transient. After simulating six different accident scenarios with reactivity insertions ranging from 0.5 to 1.3 dollar, it was found that an optimal system response could reduce peak fuel temperatures during the transient by 3.5% to 5%. Furthermore, discussion was given on how the optimal system response could be obtained using relatively simple numerical optimization algorithms due to the smoothness of the optimization problem. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Coupled Multiphysics Simulations of Heat Pipe Microreactors Using DireWolf

DireWolf is a multiphysics software driver application designed to simulate heat pipe–cooled nuclear microreactors. Developed under the U.S. Department of Energy, Office of Nuclear Energy Nuclear Energy Advanced Modeling and Simulation (NEAMS) program, the DireWolf software application’s objective is to provide the nuclear community with a design and safety analysis simulation capability. Based upon the NEAMS program Multiphysics Object-Oriented Simulation Environment (MOOSE) computational framework, DireWolf tightly couples nuclear microreactor physics, reactor physics, radiation transport, nuclear fuel performance, heat pipe thermal hydraulics, power generation, and structural mechanics to resolve the interdependent nonlinearities. DireWolf is capable of simulating both steady and transient normal reactor operation and several postulated failure scenarios. We will present the fundamental physics of heat pipe–cooled nuclear microreactors and the MOOSE-based software employed in DireWolf. Both steady and transient results for coupled reactor physics, radiation transport, and nuclear fuel performance are demonstrated.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Assessment of the Griffin Reactor Multiphysics Application Using the Empire Micro Reactor Design Concept

In late 2019, INL and ANL agreed to jointly develop the reactor physics code named Griffin based on the integration of the two code suites, MAMMOTH/Rattlesnake (INL) and MC2 - 3/PROTEUS (ANL). Griffin is being developed based on the MOOSE framework and MOOSE quality assurance procedures. This decision was made to be able to allow DOE-NE to efficiently invest funding to this area and to provide effective and timely support for existing and potential users; the latter includes industry and government organizations who are developing various types of advanced reactors in the near and long term. Since MAMMOTH/Rattlesnake has been developed based on the MOOSE framework, the INL/ANL Griffin development team agreed to build Griffin beginning with a merger of MAMMOTH and Rattlesnake into a single code and moving forward by implementing capabilities from the PROTEUS suite into Griffin. Moving forward, both ANL and INL efforts are equally invested in the Griffin project, with management support, to provide an advanced reactor multiphysics tool to assist in reactor design, optimization, and safety analysis. Much work remains in moving Griffin forward to migrate PROTEUS capabilities and to optimize performance to meet user needs. The main objective of this work is to assess the current status of Griffin capabilities in terms of performance and accuracy, to determine priorities for PROTEUS migration, and to identify capabilities and features to improve for supporting the code integration effort. For this assessment, the Empire micro reactor problem that was developed in the ARPA-E MEITNER program was selected as an advance reactor concept of interest to the technical community. The Empire reactor problem was expanded from its original incomplete specification to be a small heat-pipe-cooled micro reactor core with ~113 cm radius and 70 cm in height, composed of 18 fuel assemblies, 12 control drums, and beryllium radial and axial reflectors. In the current model, using 5 cm axial reflectors specified in the original Empire assembly model, more than 10% of neutrons leak axially and through the empty center safety hole, as well as through heat pipe channels in fuel assembly elements that extend through the top reflector region. Several calculation models of the core were defined for systematic assessment, including 2-D and 3-D fuel assemblies and whole cores with cylindrical boundaries. Cross sections were generated using Serpent 2, and meshes were produced using the Argonne mesh tool or the INL neutronics meshing tools combined with CUBIT. Cross sections and meshes were converted to the ISOXML and Exodus formats, respectively, so that Griffin and PROTEUS could use consistent data for solving the reactor problems. With the prepared cross sections and meshes, PROTEUS was run first to ensure that all input data were correctly generated and input options in terms of angle, mesh, and energy group were accurately determined. Comparisons against Serpent 2 solutions were made in terms of eigenvalue and pin power. The same calculations and comparisons were then conducted using Griffin. For the fuel assembly and whole core problems, the PROTEUS eigenvalues agreed well with reference Serpent 2 solutions within 100 and 30 pcm, respectively, and pin power differences relative to Serpent 2 were overall less than 2.2% and RMS 0.8% for the whole core models. This indicated that all input data were properly prepared. Using the same data, Griffin was run selecting the SAAF-CFEM SN solver with Legendre-Gaussian quadrature and NDA and DSA for acceleration. It was found that the SAAF-CFEM solver of Griffin required finer meshes to achieve eigenvalue and pin power solutions in good agreement with Serpent 2, consequently requiring more memory requirement and longer computation time. On the other hand, the SPH-Diffusion 2-D core calculations performed using Griffin were able to recover the exact eigenvalue from the reference Serpent 2 solutions, resulting in a pin-power distribution with an RMS of 0.6% and maximum absolute difference of less than 1.4%. The runtimes for SPH-Diffusion for the 2-D core were less than 3 minutes on 40 cores. During this evolution of this evaluation, many updates were made in Griffin by the Griffin development team of INL (focusing on software updates) and ANL (reviewing and supporting software updates) to complete this assessment. Observations from the code assessment are presented in the conclusion section of this report, followed by a discussion of recommendations for future work.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Impact of Grain Size on Performance Degradation of TREAT LEU

We argue that radiation damage induced degradation of thermal conductivity does not set a lower limit on fuel grain sizes for the low enriched uranium fuel design of the Transient Reactor Test Facility (TREAT). Earlier work reports that smaller grains cause a larger degradation of thermal conductivity than larger grains constraining the smallest feasible size of fuel grains. This work assesses TREAT’s transient performance in the presence of radiation damage. The difference between the two studies is in treating damaged and fresh graphite as serial (this work) or parallel (previous) heat resistors. We use a multiphysics model of TREAT fuel grains to compute the reduction in transient capability measured by the total deposited energy as a function of irradiation dose. We find that radiation damage has a negligible effect on energy deposition.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Hybrid super homogenization and discontinuity factor method for continuous finite element diffusion

This paper presents a novel homogenization equivalence technique aiming to simultaneously leveragethe simplicity of the Super Homogenization (SPH) method to reproduce reference reaction rates andthe ability to preserve reference leakage rates at desired surfaces through Discontinuity Factors (DF).The need for this new class of methods arises from the inability of the current state-of-the-art SPH technology to properly reproduce the reactor multiplication factor for problems with significant leakage. This work shows that this defect lies in the use of normalization factors in the SPH algorithm: while they are necessary with purely reflecting problems to ensure uniqueness of the solution, they introduce homogenization inconsistencies if at least one vacuum boundary condition is present. Two solutions to this problem are presented in this work: (i) to simply remove the normalization factor or (ii) to introduce additional degrees of freedom in the form of DFs in such a way that the normalization factors can still constrain the problem. While the former clearly offers unrivaled simplicity and can lead to very satisfactory results for leakage-dominated cores or if spatial restriction of the SPH regions is applied – as demonstrated for the High Temperature Test Reactor, the latter is more robust and does not require to scale the fission terms with the reference eigenvalue.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Control rod treatment for FEM based radiation transport methods

This paper presents a novel control rod treatment for finite element method (FEM) based reactor physics simulations. The new method falls into the class of homogenization methods which treat material interfaces within mesh elements by defining a representative, homogenized nuclear cross section set. In contrast to existing homogenization based cusping treatments that attempt to approximate flux-volume weighting of the cross sections, we propose to exactly integrate terms appearing in the variational form of the transport or diffusion equation over mixed material elements. This goal is achieved by defining smoothly varying cross sections in elements that straddle material boundaries. It is shown that the smoothly varying cross sections can be obtained by projecting the piecewise set of cross sections onto the set of Legendre polynomials up to a finite order. Implementation of smoothly varying cross sections is supported within the Rattlesnake radiation multiphysics code that is currently under development at the Idaho National Laboratory. Homogenization methods traditionally suffer from cusping effects that originate from overestimation of absorption cross sections in strongly neutron-absorbing materials as found in control rods. We demonstrate that the presented method is (1) highly effective in removing cusping effects and (2) provides accurate results based on the C5G7-TD benchmark, a time-dependent version of the C5G7 benchmark.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Iterated Discontinuity Factors Based on Reference Outgoing Currents for Discontinuous Finite Element Diffusion

We present a novel formulation for iteratively computing Discontinuity Factors (DF) designed to reproduce reference partial outgoing currents at the interface between macro-regions using Discontinuous Galerkin Finite Elements to solve the multigroup neutron diffusion equation. Similarly, an expression for the boundary coefficients (BCf) is proposed to match the partial outgoing current at vacuum boundaries. Upon convergence, macro-region averaged reaction and leakage rates are preserved. In addition, we consider a source-free steady-state problem depending on the DFs. The existence of a non-trivial solution is due to the non-linearity of the problem. This form greatly simplifies the implementation within Rattlesnake and efficiently converges by updating the DFs and BCfs at every linear iteration of the Preconditioned Jacobian-Free Newton-Krylov solver. The main challenge then lies in determining an appropriate scaling factor to ensure that the initial values for the DFs and BCfs are not too far from their converged value. While this factor does not change the final solution, it has the potential to significantly affect convergence, for purely numerical reasons. An expression based on the reference fission source integral is proposed and satisfying results are presented for problems and compared to Superhomogénéisation (SPH) results with both reflecting and vacuum boundary conditions.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Iterated Discontinuity Factors Based on Reference Outgoing Currents for Discontinuous Finite Element Diffusion

We present a novel formulation for iteratively computing Discontinuity Factors (DF) designed to reproduce reference partial outgoing currents at the interface between macro-regions using Discontinuous Galerkin Finite Elements to solve the multigroup neutron diffusion equation. Similarly, an expression for the boundary coefficients (BCf) is proposed to match the partial outgoing current at vacuum boundaries. Upon convergence, macro-region averaged reaction and leakage rates are preserved. In addition, we consider a source-free steady-state problem depending on the DFs. The existence of a non-trivial solution is due to the non-linearity of the problem. This form greatly simplifies the implementation within Rattlesnake and efficiently converges by updating the DFs and BCfs at every linear iteration of the Preconditioned Jacobian-Free Newton-Krylov solver. The main challenge then lies in determining an appropriate scaling factor to ensure that the initial values for the DFs and BCfs are not too far from their converged value. While this factor does not change the final solution, it has the potential to significantly affect convergence, for purely numerical reasons. An expression based on the reference fission source integral is proposed and satisfying results are presented for problems and compared to Superhomogénéisation (SPH) results with both reflecting and vacuum boundary conditions.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Enhanced geometric capabilities for the transient analysis code T-ReX and its application to simulating TREAT experiments

Here, advances in computational architecture have prompted a resurgence in the simulation of reactor transients from first principles. Most codes are unable to simulate transient events with complex models, and require numerous approximations. The code T-ReX (Transient-Reactor eXperiment simulator), an extensive update to TDKENO, has been developed as a transient analysis tool with few geometric limitations and minimal theoretical approximations. T-ReX achieves this by employing the Improved Quasi-Static (IQS) method to solve the time dependent Boltzmann transport equation with explicit representation of delayed neutrons. The primary change in T-ReX relative to TDKENO is the incorporation of a modified version of the Monte Carlo code KENO-VI to calculate the flux shape and model the geometry of a problem. Using KENO-VI to model systems allows exact representation of the geometry. The changes to T-ReX are verified by comparison of solutions to computational benchmark problems found with a previous version of TDKENO that made use of KENO V.a, and several other codes with time-dependent capabilities. In addition, a three-dimensional model of the Transient Reactor Test Facility (TREAT) core at the Idaho National Laboratory (INL) is constructed with KENO-VI, and used to validate T ReX. T-ReX produces results that agree with benchmark problems, and are in better agreement with TREAT experimental data than TDKENO.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Multischeme transport with upwinding for Rattlesnake code

This report conclude our efforts at INL to make Rattlesnake, the MOOSE-based radiation multigroup transport application, fully support the multischeme transport capability. Specifically, it details all five types of interface condition with upwinding method for coupling eight available discretization schemes within Rattlesnake. These discretization schemes include SN (discrete ordinates method), PN (spherical harmonics expansion method) and diffusion for angular discretization, and continuous finite element method (CFEM) and discontinuous finite element method (DFEM) for spatial discretization. The other type of method based on Lagrange multipliers for coupling schemes based on CFEM has been studied in the past. Besides simple test problems, a more realistic application of multischeme transport for TREAT (transient reactor test facility) experiment modeling are presented. Several enhancements are reviewed at the end which could potentially be useful in the future.

97 MATHEMATICS AND COMPUTING↗

Advanced Modeling and Simulation Capabilities in MAMMOTH

In this presentation, we described the Advanced Modeling and Simulation Capabilities in MAMMOTH. We present the decoupled and multi-scheme capabilities and look at results for the MSERTTA experiment in TREAT.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

University Research in Support of TREAT Modeling and Simulation, FY 2017

INL is currently evolving a modeling and simulation (M&S) capability that will enable im- proved core operation as well as design and analysis of TREAT experiments. This M&S capability primarily uses MAMMOTH, a reactor physics application being developed under the Multi-physics Object Oriented Simulation Environment (MOOSE) framework. MAMMOTH allows the coupling of a number of other MOOSE-based applications. This work is being supplemented by related research projects at a number of universities. INL is funding TREAT-related research at North Carolina State University, University of New Mexico, Oregon State University, and MIT under internally funded projects within the INL/Battelle National University Consortium Program. Under the DOE Nuclear Energy Advanced Modeling and Simulation program (NEAMS), other research is being performed at MIT, University of Florida, and Texas A&M University. In addition, Dr. Barry Ganapol of University of Arizona was funded for summer work at the INL. This report is a compilation of conference papers that were submitted as part of this research by the NEAMS University partners and from the visiting professor.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗