Search NASA⌕ Search

Engineering topics

DeLuca, Racci

Publications and source records attributed to DeLuca, Racci.

Time-Temperature-Stress Superposition of PBX 9502 Compressive Creep Data for Lifetime Predictions

The plastic-bonded explosive (PBX) 9502 is a viscoelastic, high-solids loaded polymer bound composite comprised of 95 weight% (wt%) TATB explosive crystals and 5 wt% FK-800 polymer binder. The uniaxial quasi-static mechanical properties have been studied and characterized extensively over 25+ years, including creep. Creep is the strain evolution over time as a result of an asymmetric load typically at temperatures above ambient. Creep measurements to failure can take excessively long periods of time depending on various factors including applied stress, temperature, and loading rate that render a single test to failure impossible. Using the principles of time-temperature-stress superposition (TTSSP), short-term creep tests at various applied stresses and temperatures can be used for long-term creep predictions. The TTSSP model shifts short-term test data using two factors, one for temperature and stress, creating a master curve at a reference test condition. The master curve can be shifted to predict the creep response at any desired test condition. PBX 9502 compression specimens were tested at three temperatures and various applied stresses. This work discusses the TTSSP analysis of PBX 9502 compressive creep data to create a single comprehensive master curve.

36 MATERIALS SCIENCE↗

Coefficient of Thermal Expansion during Ratchet Growth of TATB Compactions

Triamino trinitrobenzene (TATB) is an insensitive high explosive, meaning that it is quite immune from accidental detonation and only performs in appropriately engineered configurations. While this is advantageous for applications, the TATB crystal is graphitic and possesses significant thermal and mechanical anisotropy. Compactions of TATB crystals, with or without binder, have been shown to have oriented TATB crystals that relate to the pressing geometry and process, and this TATB texture necessarily imparts microscale and macroscale anisotropy to the compaction. By a mechanism not fully understood, thermal cycling results in irreversible volume expansion (also called ratchet growth) of the compaction likely by creating stress points on the microscale. Changes in density caused by thermal cycling can certainly effect the explosive performance. Our past characterization of the ratchet growth phenomenon has focused on the magnitude of the irreversible strain as measured before and after a thermal cycle. Finally, in the work presented here, we analyze the evolving thermal expansion behavior during the ascending and descending temperature ramps, providing further insight into the material changes taking place during the ratchet growth phenomenon.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

TATB ratchet growth and hydrostatically-confined PBX 9502

The explosive TATB (1,3,5-triamino-2,4,6-trinitirobenzene) is formulated with various polymeric binders to create plastic-bonded explosives like PBX 9502 (95 wt% TATB and 5 wt% Kel-F binder). TATB crystals are graphitic and plate-like in nature and single crystals exhibit anisotropic thermal expansion where the direction normal to the platelet surface grows 10-20 times more than the in-plane platelet direction. Compactions of TATB, with and without binder, exhibit irreversible volume expansion, also known as ratchet growth, when thermal cycled to hot or cold temperatures. Specifically, when TATB-based compactions return to ambient after a temperature excursion away from room temperature, the volume of the specimen is slightly larger. Repeated thermal cycles can reduce the density by 1 to 2%. Axial confinement on a cylindrical specimen has previously been shown by us to suppress growth in the confining direction but then increase growth in the unconfined directions (likely due to creep effects). In the work presented here, PBX 9502 specimens were placed in cup assemblies where they were embedded in Sylgard (an incompressible silicon resin) to provide hydrostatic confinement when the assemblies were placed under different axial loads. The loaded cup assemblies were thermally cycled 10 times to hot and cold temperatures. Finally, results show that increasing the hydrostatic confining pressure causes a decrease in the PBX 9502 volume expansion that occurs.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Spherical Platen versus Flat Platens in Compression Testing of PBX 9502

For ~15 years and perhaps longer, Pantex Plant has used a spherical platen in their compression load train when performing compression tests for Core Surveillance and HE Qualification. As our mechanical testing team at Los Alamos National Laboratory has always worked closely with our Pantex colleagues, and has maintained very similar practices in terms of calibration and testing, the author of this report has documented discussions with Pantex personnel (Robert Spence, et al.) dating back to ~2003, discussing the pros and cons of spherical platen use. LANL used spherical platens for a year or two, but determined issues and discontinued the practice. Based on multiple Engineering Evaluations (EE), LANL opportunities to watch Pantex procedures, it is our understanding that Pantex continued to use spherical platens from circa 2003 (or earlier) through summer 2019, despite the discontinued practice at LANL and the strong encouragement from LANL that spherical platens introduced error and should not be used. The short study reported here was intended to provide quantitative argument as to why spherical platens should not be used. As of a mechanical testing EE in August 2019, and after the testing of this LANL study was complete, LANL was informed by Pantex personnel that the practice of using spherical platens had recently been discontinued with no obvious problems or changes to the quality of the data. Although the urgency is gone for reporting our results, this is a brief quick summary of the data we collected.

42 ENGINEERING↗

Thermal and Mechanical Characterization of DAAF and LAX-133 (FY19 Summary Report)

We have performed a series of thermal and mechanical tests to characterize the high explosive 3,3’-diamino-4,4’-azofurazan (DAAF), as well as the formulated version LAX-133 (97 wt% DAAF and 3 wt% FK-800 binder, now also referred to as PBX 9701; for clarity in this report, we will use the name LAX-133 which is what the formulated material was called at the time this work was performed). Specifically, we have used axially die-pressed cylinders (with no further machining) of neat DAAF and of LAX-133 to make measurements of compressive strength, Brazil disk, coefficient of thermal expansion (CTE), as well as irreversible volume expansion with thermal cycling (ratchet growth).

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

Thermal Cycling and Ratchet Growth of TATB and PBX 9502

The irreversible volume expansion, or ratchet growth, of TATB and PBX 9502 (95 weight% TATB) compactions has been quantified over a wide range of thermal cycles. While the precise TATB texture distributions of these specimen sets are likely different from each other, we believe they are consistent within each set, as the expansion data show reproducibility and consistency. These data provide a baseline characterization of the ratchet growth phenomenon in these materials. The increased expansion that comes with changes in the temperature range of the cycles is quantified, repeated hot cycles growing far more than cold. For thermal cycles above ambient where the temperature range is increased in subsequent cycles, the growth of a given cycle is shown to be dictated by previously-established growth trajectories, and the specimen will grow according to the growth potential associated with the temperature range of the present cycle. Alternating hot-cold cycles greatly enhances the cold-cycle contributions as compared to the growth of cold cycles alone. These “rules” of ratchet growth are first established, then observed to hold true for more complex sequences of hot and cold cycles. Finally, a simple equation is used to parameterize the response of individual data sets.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

LT61LEP-40 Phase II, Final Report

LT-40 Phase II evaluates the shear strength of Wilethane 44 (W44) when bonded to plastic bonded explosives (PBXs) as a function of accelerated aging time. These tests involve two PBX formulations, PBX 9502 and PBX 9012 (which is identical to the LX-07 formulation but lacks the orange dye). The LT-40 Phase I and Phase II test series differ from each other in their use of different lots of the two PBX formulations. The earlier LT-40 Phase I reports captured the initial shear strength data aged to 6 months [1] and18 months [2] for LX-07 lot 692 -5 and PBX 9502 lot 891-008. The Phase I final report [2] incorrectly refers to LX -07 as PBX 9012. These materials have the same formulation but, again, LX-07 includes orange dye. This report gives the Phase II data which includes the test results of 3-month and 6-month specimens [3] along with the18-month aged specimens of PBX 9012 Development Lot 1 and PBX 9502 Development Lot 2. The summary of all the LT-40 Phase II results are given and compared with the Phase I work. In a separate study, LT61LEP-21 [4 ], using the same Iosipescu loading configuration, the dependence of W44 shear bond strength as a function of cure time was investigated on the Phase I lots.

36 MATERIALS SCIENCE↗

Impact Sensitivity and Ignition Mechanisms of Nanoaluminum-poly(perfluorinated methacrylate) Nanocomposites

Nanoenergetic composites are of overwhelming interest to the Department of Defense because of the higher power output and the ability to finely tune the ignition thresholds of these composites. Recently, several variants of a nanoaluminum-poly(perfluorinated methacrylate) (AlFA) have been synthesized and optimized for a variety of applications including reactive warhead liners and bullet spotters. While conventional techniques such as thermal analysis and bomb calorimetry can be used to characterize the reaction mechanism and energy output of AlFA composites, characterizing their dynamic behaviour is more challenging. Bullet spotter applications require a material to be impact sensitive at very low velocities, yet be adequately insensitive. Several live-fire tests were conducted which revealed the AlFA 50 material reacted consistently upon target impact at high velocities, but unreliably at very low velocities. In an effort to better understand the fundamental impact ignition mechanism and to determine the impact velocity threshold of AlFA 50 a series of Taylor gas gun experiments were conducted. It was determined that the light-initiation mechanism was consistent with a pinch mechanism, and that the ignition velocity threshold was near 74 m/s. Based on these results, it was hypothesized that the addition of a filler material could be used to sensitize the AlFA 50 , and that Asay shear impact testing could be used to determine a more optimal shape of such inclusions. Experiments performed using the Asay shear impact test setup confirmed the pinch ignition mechanism, but observations also revealed that the size of the pinch point was important. It was shown that the addition of large glass beads (> 1mm in diameter) was effective at sensitizing the AlFA 50 material at high and low velocities, with ignition observed at impact velocities as low as 35 m/s.

36 MATERIALS SCIENCE↗

The Volumetric Coefficient of Thermal Expansion of PBX 9502

TATB (1,3,5-triamino-2,4,6-trinitrobenzene) is an insensitive high explosive (IHE) used in plastic-bonded explosives (PBXs) such as PBX 9502. TATB’s plate-like crystals have highly anisotropic coefficient of thermal expansion (CTE) values, where the through-plane direction grows about twice as much as the in-plane directions. Compactions of TATB have preferred alignment of crystals, with resulting CTE anisotropy. Additionally, TATB-based compactions exhibit anisotropic irreversible volume expansion (ratchet growth) when thermal cycled to temperatures away from ambient. From a series of measurements on a thermal mechanical analyzer (TMA), the initial thermal ramps away from ambient were used to estimate the volumetric coefficient of thermal expansion of PBX 9502. The TMA measures the change in axial strain of the material as a function of temperature. Starting at ambient, thermal ramps of 1°C per minute were conducted to various endpoint temperatures from -43°C to 173°C on specimens machined from isostatically-pressed hemispheres of PBX 9502. Anisotropy was measured and the volumetric CTE estimated over this temperature range. For ease of use by experimentalists, a 5th-order polynomial was fit to the calculated change in density as a function of temperature. The CTE of neat TATB, PBX 9502, and the Kel-F binder were compared over the given temperature range. At lower temperatures, TATB expands more than PBX 9502 until the melt temperature of Kel-F (80°C), above which the two exhibit similar CTE values.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

Coefficient of Thermal Expansion of Pressed PETN Pellets

The PETN single crystal coefficient of thermal expansion (CTE) values were measured and reported by Cady in 1972 [1] over the temperature range of -160 to 100°C. Measurements were made in the (001) and (100) crystallographic directions, see Figure 1 (a replicate of Figure 1 from the Cady paper). Cady used his single-crystal data to calculate the linear CTE for a randomly-oriented multi-crystal pressing of PETN, and his values ranged from 76.5 με/°C (at 20°C) to 89.9 5 με/°C (at 90°C).

36 MATERIALS SCIENCE↗