Search NASA⌕ Search

Engineering topics

Deckert, J. C.

Publications and source records attributed to Deckert, J. C..

18 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

A design methodology for robust failure detection and isolation

A decentralized failure detection and isolation (FDI) methodology, which is robust with respect to model uncertainties and noise, is presented Redundancy metrics are developed, and optimization problems are posed for the choices of robust parity relations. Closed-form solutions for some special failure cases are given. Connections are drawn with other disciplines, and the use of the metrics to evaluate alternative FDI schemes is discussed.

Pattipati, K. R.↗
NASA NTRS1983

Analytic redundance management for flight control sensors

The formulation and flight test results of an algorithm to detect and isolate the first failure of any one of 12 duplex control sensor signals (24 in all) being monitored are reviewed. The technique uses like signal differences for fault detection while relying upon analytic redundancy relationships among unlike quantities to isolate the faulty sensor. The fault isolation logic utilizes the modified sequential probability ratio test, which explicitly accommodates the inevitable, irreducible low frequency errors present in the analytic redundancy residuals. In addition, the algorithm used sensor output selftest, which takes advantage of the duplex sensor structure by immediately removing a hard failed sensor from control calculations and analytic redundancy relationships while awaiting a definitive fault isolation decision via analytic redundancy. This study represents a proof of concept demonstration of a methodology that is applied to duplex or higher flight control sensor configurations and, in addition, can monitor the health of one simplex signal per analytic redundancy relationship.

Deckert, J. C.↗
NASA NTRS1983

Analytical redundancy management mechanization and flight data analysis for the F-8 digital fly-by-wire aircraft flight control sensors

The details are presented of an onboard digital computer algorithm designed to reliably detect and isolate the first failure in a duplex set of flight control sensors aboard the NASA F-8 digital fly-by-wire aircraft. The algorithm's successful flight test program is summarized, and specific examples are presented of algorithm behavior in response to software-induced signal faults, both with and without aircraft parameter modeling errors.

Deckert, J. C.↗
NASA NTRS1981

F-8 digital fly-by-wire aircraft analytic redundancy management flight test experience

The formulation and flight test results of an algorithm to detect and isolate the first failure of any one of twelve duplex control sensors being monitored are described. The technique uses like sensor output differences for fault detection while relying upon analytic redundancy relationships among unlike quantities to isolate the faulty sensor. The fault isolation logic utilizes the modified sequential probability ratio test, which explicitly accommodates the inevitable irreducible low frequency errors present in the analytic redundancy residuals. In addition, the algorithm uses sensor output selftest, which takes advantage of the duplex sensor structure by immediately removing a highly erratic sensor from control calculations and analytic redundancy relationships while awaiting a definitive fault isolation decision via analytic redundancy.

Deckert, J. C.↗
NASA NTRS1981

Flight test results for the F-8 digital fly-by-wire aircraft control sensor analytic redundancy management technique

This paper reviews the formulation and flight test results of an algorithm to detect and isolate the first failure of any one of twelve duplex control sensor signals being monitored. The technique uses like-signal differences for fault detection while relying upon analytic redundancy relationships among unlike quantities to isolate the faulty sensor. The fault isolation logic utilizes the modified sequential probability ratio test, which explicitly accommodates the inevitable irreducible low frequency errors present in the analytic redundancy residuals. In addition, the algorithm uses sensor output selftest, which takes advantage of the duplex sensor structure by immediately removing a highly erratic sensor from control calculations and analytic redundancy relationships while awaiting a definitive fault isolation decision via analytic redundancy. This study represents a proof of concept demonstration of a methodology that can be applied to duplex or higher flight control sensor configurations and, in addition, can monitor the health of one simplex signal per analytic redundancy relationship.

Deckert, J. C.↗
NASA NTRS1978

Reliable dual-redundant sensor failure detection and identification for the NASA F-8 DFBW aircraft

A technique was developed which provides reliable failure detection and identification (FDI) for a dual redundant subset of the flight control sensors onboard the NASA F-8 digital fly by wire (DFBW) aircraft. The technique was successfully applied to simulated sensor failures on the real time F-8 digital simulator and to sensor failures injected on telemetry data from a test flight of the F-8 DFBW aircraft. For failure identification the technique utilized the analytic redundancy which exists as functional and kinematic relationships among the various quantities being measured by the different control sensor types. The technique can be used not only in a dual redundant sensor system, but also in a more highly redundant system after FDI by conventional voting techniques reduced to two the number of unfailed sensors of a particular type. In addition the technique can be easily extended to the case in which only one sensor of a particular type is available.

Deckert, J. C.↗
NASA NTRS1977

F-8 DFBW sensor failure identification using analytic redundancy

The structure of a sensor failure detection and identification system designed for the NASA F-8 DFBW aircraft is outlined. The system is for use in a dual-redundant environment, and it takes maximal advantage of all functional relationships among the sensed variables. The identification logic uses the quality sequential probability ratio, which provides a useful on-line measure of confidence in the various forms of analytic redundancy. Preliminary simulation results indicate good behavior of the analytic decision statistic, based on the sequential probability ratio test.

Deckert, J. C.↗
NASA NTRS1977

Evaluation of the F-8 DFBW analytic redundancy sensor FDI algorithm using telemetry data

In this paper we present a reliable technique for failure detection and identification (FDI) for dual redundant flight control sensors aboard the NASA F-8 digital fly-by-wire (DFBW) aircraft, and we discuss the successful application of the technique to identifying failures injected on test flight telemetry data. The technique exploits the analytic redundancy which exists as relationships among variables being measured by dissimilar instruments. With straightforward modification the technique may be extended to provide failure monitoring of a single remaining sensor after the identified failure of its companion sensor.

Deckert, J. C.↗
NASA NTRS1976

Dual redundant sensor FDI techniques applied to the NASA F8C DFBW aircraft

An onboard failure detection and identification (FDI) technique for dual redundant sensors on the NASA F8C digital fly-by-wire (DFBW) aircraft is presented. The failure of one of a pair of sensors of the same type is detected by a direct redundancy trigger which observes the difference between the outputs of these two sensors. Identification of the failed sensor is accomplished utilizing the analytic redundancy that exists as kinematic and functional relationships among the variables being measured by dissimilar instruments. In addition, identification of generic failures, common to both instruments of a given type, is accomplished by using a time trigger to periodically initiate analytic redundancy failure identification tests for individual sensors. The basic form of these tests is the comparison of the measurement of a variable using the suspect instrument with another measurement of the same variable obtained using other instrument types.

Desai, M. N.↗
NASA NTRS1976

A reliable dual-redundant sensor FDI system for the NASA F8C-DFBW aircraft

In this paper we outline the structure of a sensor failure detection and identification (FDI) system designed for the NASA F8C DFBW aircraft. The system is for use in a dual-redundant environment, and it takes maximal advantage of all functional and kinematic relationships among the sensed variables. The technique is reliable in that we have designed the system to account for a variety of unmodeled effects and have introduced a new concept - the quality sequential probability ratio (QSPR) - that provides a useful measure of our confidence in each test. The methodology used for determining detector parameters and the 'outer loop logic' for combining the various sources of information are described.

Deckert, J. C.↗
NASA NTRS1975

Maximum likelihood failure detection techniques applied to the shuttle orbiter reaction control subsystem

A technique for on-board detection and identification of hard failures and leaks of the shuttle orbiter reaction control subsystem jets, during the orbital flight phase, is presented. The method uses gimbal angle and linear accelerometer measurements from the orbiter inertial measurement unit and requires no additional hardware. Extended Kalman filters with residual traps are employed for state estimation, and generalized likelihood ratio tests for jet failure identification. Rigid body simulation results indicate identification times of less than 2 seconds for hard jet failures and less than 70 seconds for jet leaks.

Deckert, J. C.↗
NASA NTRS1973

Minimax failure detection and identification in redundant gyro and accelerometer systems.

Minimax algorithms for failure detection and identification for redundant noncolinear arrays of single-degree-of-freedom gyros and accelerometers are described. These algorithms are optimum in the sense that detection occurs as soon as it is no longer possible to account for the instrument outputs as the outputs of good instruments operating within their noise tolerances, and identification occurs as soon as it is true that only a particular instrument failure could account for the actual instrument outputs within the noise tolerance of good instruments. An estimation algorithm is described which minimizes the maximum possible estimation error magnitude for the given set of instrument outputs. Monte Carlo simulation results are presented for the application of the algorithms to an inertial reference unit consisting of six gyros and six accelerometers in two alternate configurations.

Potter, J. E.↗
NASA NTRS1972

Gyro and accelerometer failure detection and identification in redundant sensor systems

Algorithms for failure detection and identification for redundant noncolinear arrays of single degree of freedom gyros and accelerometers are described. These algorithms are optimum in the sense that detection occurs as soon as it is no longer possible to account for the instrument outputs as the outputs of good instruments operating within their noise tolerances, and identification occurs as soon as it is true that only a particular instrument failure could account for the actual instrument outputs within the noise tolerance of good instruments. An estimation algorithm is described which minimizes the maximum possible estimation error magnitude for the given set of instrument outputs. Monte Carlo simulation results are presented for the application of the algorithms to an inertial reference unit consisting of six gyros and six accelerometers in two alternate configurations.

Potter, J. E.↗
NASA NTRS1972

Gyro and accelerometer failure detection and identification in redundant sensor systems.

An algorithm for failure detection and identification for redundant non-orthogonal arrays of single degree of freedom gyros and accelerometers is described which is optimum in the sense that detection occurs as soon as it is no longer possible to account for the instrument outputs as the outputs of good instruments operating within their noise tolerances, and identification occurs as soon as it is true that only a particular instrument failure could account for the actual instrument outputs within the noise tolerance of good instruments. An estimation algorithm is described which minimizes the maximum possible error magnitude for the given set of instrument outputs. Monte Carlo simulation results are presented for the application of the algorithms to an inertial reference unit consisting of six gyros and six accelerometers in two alternate configurations.

Potter, J. E.↗
NASA NTRS1971

Optimal filtering in the presence of unmodeled time correlated driving disturbances.

In many realistic data filtering problems, the cross correlation of the state estimation error and the state forcing function is unknown due to the poor knowledge of the time history of the forcing function. In this paper, the conservative and minimal approximation to the cross correlation terms is presented. It requires only the knowledge of the estimation error covariance and the forcing function covariance, with the choice of an associated free parameter left to the user. If the estimation error covariance and/or the forcing function covariance are bounded from above but not known exactly, the cross correlation approximation using those upper bounds remains conservative. This cross correlation approximation leads to a conservative approximation to the estimation error covariance matrix differential equation between measurement times. The free parameter is determined as the analytic solution to an associated optimal control problem. The procedure is expanded to include discrete linear measurement incorporation.

Fraser, D. C.↗
NASA NTRS1970

Method of statistical filtering

Minimal formula for bounding the cross correlation between a random forcing function and the state error when this correlation is unknown is used in optimal linear filter theory applications. Use of the bound results in overestimation of the estimation-error covariance.

Battin, R. H.↗