Search NASA⌕ Search

Engineering topics

Dedrick, Daniel E

Publications and source records attributed to Dedrick, Daniel E.

Durability study of a vehicle-scale hydrogen storage system.

Sandia National Laboratories has developed a vehicle-scale demonstration hydrogen storage system as part of a Work for Others project funded by General Motors. This Demonstration System was developed based on the properties and characteristics of sodium alanates which are complex metal hydrides. The technology resulting from this program was developed to enable heat and mass management during refueling and hydrogen delivery to an automotive system. During this program the Demonstration System was subjected to repeated hydriding and dehydriding cycles to enable comparison of the vehicle-scale system performance to small-scale sample data. This paper describes the experimental results of life-cycle studies of the Demonstration System. Two of the four hydrogen storage modules of the Demonstration System were used for this study. A well-controlled and repeatable sorption cycle was defined for the repeated cycling, which began after the system had already been cycled forty-one times. After the first nine repeated cycles, a significant hydrogen storage capacity loss was observed. It was suspected that the sodium alanates had been affected either morphologically or by contamination. The mechanisms leading to this initial degradation were investigated and results indicated that water and/or air contamination of the hydrogen supply may have lead to oxidation of the hydride and possibly kinetic deactivation. Subsequent cycles showed continued capacity loss indicating that the mechanism of degradation was gradual and transport or kinetically limited. A materials analysis was then conducted using established methods including treatment with carbon dioxide to react with sodium oxides that may have formed. The module tubes were sectioned to examine chemical composition and morphology as a function of axial position. The results will be discussed.

08 HYDROGEN↗

Mitigation technologies for hydrogen storage systems based on reactive solids.

This paper describes mitigation technologies that are intended to enable the deployment of advanced hydrogen storage technologies for early market and automotive fuel cell applications. Solid State hydrogen storage materials provide an opportunity for a dramatic increase in gravimetric and volumetric energy storage density. Systems and technologies based on the advanced materials have been developed and demonstrated within the laboratory [1,2], and in some cases, integrated with fuel cell systems. The R&D community will continue to develop these technologies for an ever increasing market of fuel cell technologies, including, forklift, light-cart, APU, and automotive systems. Solid state hydrogen storage materials are designed and developed to readily release, and in some cases, react with diatomic hydrogen. This favorable behavior is often accomplished with morphology design (high surface area), catalytic additives (titanium for example), and high purity metals (such as aluminum, Lanthanum, or alkali metals). These favorable hydrogen reaction characteristics often have a related, yet less-desirable effect: sensitivity and reactivity during exposure to ambient contamination and out-of-design environmental conditions. Accident scenarios resulting in this less-favorable reaction behavior must also be managed by the system developer to enable technology deployment and market acceptance. Two important accident scenarios are identified through hazards and risk analysis methods. The first involves a breach in plumbing or tank resulting from a collision. The possible consequence of this scenario is analyzed though experimentally based chemical kinetic and transport modeling of metal hydride beds. An advancing reaction front between the metal hydride and ambient air is observed to proceed throughout the bed. This exothermic reaction front can result in loss of structural integrity of the containing vessel and lead to un-favorable overheating events. The second important accident scenario considered is a pool fire or impinging fire resulting from a collision between a hydrocarbon or hydrogen fueled vehicle. The possible consequence of this scenario is analyzed with experimentally-based numerical simulation of a metal hydride system. During a fire scenario, the hydrogen storage material will rapidly decompose and release hydrogen at high pressure. Accident scenarios initiated by a vehicular collision leading a pipe break or catastrophic failure of the hydride vessel and by external pool fire with flame engulfing the storage vessel are developed using probabilistic modeling. The chronology of events occurring subsequent to each accident initiator is detailed in the probabilistic models. Technology developed to manage these scenarios includes: (1) the use of polymer supports to reduce the extent and rate of reaction with air and water, (2) thermal radiation shielding. The polymer supported materials are demonstrated to provide mitigation of unwanted reaction while not impacting the hydrogen storage performance of the material. To mitigate the consequence of fire engulfment or impingement, thermal radiation shielding is considered to slow the rate of decomposition and delay the potential for loss-of-containment. In this paper we explore the use of these important mitigation technologies for a variety of accident scenarios.

08 HYDROGEN↗

Process development and techno-economic analysis of a novel process for MeOH production from CO2 using solar-thermal energy.

Mitigating and overcoming environmental problems brought about by the current worldwide fossil fuel-based energy infrastructure requires the creation of innovative alternatives. In particular, such alternatives must actively contribute to the reduction of carbon emissions via carbon recycling and a shift to the use of renewable sources of energy. Carbon neutral transformation of biomass to liquid fuels is one of such alternatives, but it is limited by the inherently low energy efficiency of photosynthesis with regard to the net production of biomass. Researchers have thus been looking for alternative, energy-efficient chemical routes inspired in the biological transformation of solar power, CO2 and H2O into useful chemicals; specifically, liquid fuels. Methanol has been the focus of a fair number of publications for its versatility as a fuel, and its use as an intermediate chemical in the synthesis of many compounds. In some of these studies, (e.g. Joo et al., (2004), Mignard and Pritchard (2006), Galindo and Badr (2007)) CO2 and renewable H2 (e.g. electrolytic H2) are considered as the raw materials for the production of methanol and other liquid fuels. Several basic PFD diagrams have been proposed. One of the most promising is the so called CAMERE process (Joo et al., 1999 ). In this process, carbon dioxide and renewable hydrogen are fed to a first reactor and transformed according to: H2 + CO2 <=> H2O + CO Reverse Water Gas Shift (RWGS) After eliminating the produced water the resulting H2/CO2/CO mixture is then feed to a second reactor where it is converted to methanol according to: CO2 + 3.H2 <=> CH3OH + H2O Methanol Synthesis (MS) CO + H2O <=> CO2 + H2 Water Gas Shift (WGS) The approach here is to produce enough CO to eliminate, via WGS, the water produced by MS. This is beneficial since water has been proven to block active sites in the MS catalyst. In this work a different process alternative is presented: One that combines the CO2 recycling of the CAMERE process and the use of solar energy implicit in some of the biomass-based process, but in this case with the potential high energy efficiency of thermo-chemical transformations.

08 HYDROGEN↗

Model based design of an automotive-scale, metal hydride hydrogen storage system.

Sandia and General Motors have successfully designed, fabricated, and experimentally operated a vehicle-scale hydrogen storage system using the complex metal hydride sodium alanate. Over the 6 year project, the team tackled the primary barriers associated with storage and delivery of hydrogen including mass, volume, efficiency and cost. The result was the hydrogen storage demonstration system design. The key technologies developed for this hydrogen storage system include optimal heat exchange designs, thermal properties enhancement, a unique catalytic hydrogen burner and energy efficient control schemes. The prototype system designed, built, and operated to demonstrate these technologies consists of four identical hydrogen storage modules with a total hydrogen capacity of 3 kg. Each module consists of twelve stainless steel tubes that contain the enhanced sodium alanate. The tubes are arranged in a staggered, 4 x 3 array and enclosed by a steel shell to form a shell and tube heat exchanger. Temperature control during hydrogen absorption and desorption is accomplished by circulating a heat transfer fluid through each module shell. For desorption, heat is provided by the catalytic oxidation of hydrogen within a high efficiency, compact heat exchanger. The heater was designed to transfer up to 30 kW of heat from the catalytic reaction to the circulating heat transfer fluid. The demonstration system module design and the system control strategies were enabled by experiment-based, computational simulations that included heat and mass transfer coupled with chemical kinetics. Module heat exchange systems were optimized using multi-dimensional models of coupled fluid dynamics and heat transfer. Chemical kinetics models were coupled with both heat and mass transfer calculations to design the sodium alanate vessels. Fluid flow distribution was a key aspect of the design for the hydrogen storage modules and computational simulations were used to balance heat transfer with fluid pressure requirements. An overview of the hydrogen storage system will be given, and examples of these models and simulation results will be described and related to component design. In addition, comparisons of demonstration system experimental results to model predictions will be reported.

08 HYDROGEN↗

Risk-informed separation distances for hydrogen gas storage facilities.

The use of risk information in establishing code and standard requirements enables: (1) An adequate and appropriate level of safety; and (2) Deployment of hydrogen facilities are as safe as gasoline facilities. This effort provides a template for clear and defensible regulations, codes, and standards that can enable international market transformation.

02 PETROLEUM↗

Hydrogen release behavior.

The summary of this presentation is: (1) Barrier walls are used to reduce setbacks by factor of 2; (2) We found no ignition-timing vs. over-pressure sensitivities for jet flow obstructed by barrier walls; (3) Cryogenic vapor cloud model indicates hazard length scales exceed the room-temperature release; validation experiments are required to confirm; (4) Light-up maps developed for lean limit ignition; flammability factor model provides good indication of ignition probability; and (5) Auto-ignition is enhanced by blunt-body obstructions - increases gas temperature and promotes fuel/air mixing.

08 HYDROGEN↗

System level permeability modeling of porous hydrogen storage materials.

A permeability model for hydrogen transport in a porous material is successfully applied to both laboratory-scale and vehicle-scale sodium alanate hydrogen storage systems. The use of a Knudsen number dependent relationship for permeability of the material in conjunction with a constant area fraction channeling model is shown to accurately predict hydrogen flow through the reactors. Generally applicable model parameters were obtained by numerically fitting experimental measurements from reactors of different sizes and aspect ratios. The degree of channeling was experimentally determined from the measurements and found to be 2.08% of total cross-sectional area. Use of this constant area channeling model and the Knudsen dependent Young & Todd permeability model allows for accurate prediction of the hydrogen uptake performance of full-scale sodium alanate and similar metal hydride systems.

08 HYDROGEN↗

Complex admixtures of clathrate hydrates in a water desalination method

Disclosed is a method that achieves water desalination by utilizing and optimizing clathrate hydrate phenomena. Clathrate hydrates are crystalline compounds of gas and water that desalinate water by excluding salt molecules during crystallization. Contacting a hydrate forming gaseous species with water will spontaneously form hydrates at specific temperatures and pressures through the extraction of water molecules from the bulk phase followed by crystallite nucleation. Subsequent dissociation of pure hydrates yields fresh water and, if operated correctly, allows the hydrate-forming gas to be efficiently recycled into the process stream.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Wall pressure exerted by hydrogenation of sodium aluminum hydride.

Wall pressure exerted by the bulk expansion of a sodium aluminum hydride bed was measured as a function of hydrogen content. A custom apparatus was designed and loaded with sodium alanates at densities of 1.0, 1.1, and 1.16 g/cc. Four complete cycles were performed to identify variations in measured pressure. Results indicated poor correlation between exerted pressure and hydrogen capacity of the sodium alanate beds. Mechanical pressure due to the hydrogenation of sodium alanates does not influence full-scale system designs as it falls within common design factors of safety. Gas pressure gradients within the porous solid were identified and may limit reaction rates, especially for high aspect ratio beds.

08 HYDROGEN↗