Search NASA⌕ Search

Engineering topics

Dehoff, Ryan R.

Publications and source records attributed to Dehoff, Ryan R..

At least 37 records · Page 2

Development of Repair Techniques for Cast Iron Engine Blocks by Additive Manufacturing

ORNL partnered with Cummins Inc to demonstrate the feasibility of using additive manufacturing techniques to deposit large volume of new material on cast iron in the context of remanufacturing. Remanufacturing at Cummins Inc is carried out to repair any field damage and, in some cases, provide additional value by adding new features. Large volume deposition on difficult to weld materials is a challenging problem due to involved metallurgy. Phase-1 of this work evaluated the feasibility of using laser directed energy deposition technique to deposit new material layer by layer on cast iron engine blocks. During phase-1 deposits were made using Inconel-718, Nickel, Nr-Cr-B braze filler. Leveraging the knowledge gained during Phase-1, Phase-2 focused on developing a low- cost crack resistant ferrous alloy to repair cast iron via volume deposition techniques without preheating. Three different alloy chemistries were identified, and trials were performed on cast iron substrates to identify the optimal chemistry that provided adequate resistance to cracking in both, the deposits as well as the cast iron substrate.

42 ENGINEERING↗

Surface-hardened aluminum-rare earth alloys and methods of making the same

Embodiments of surface-hardened aluminum-rare earth alloys and methods of making the alloys are disclosed. In some embodiments, the alloy comprises aluminum and 4 wt % to 60 wt % of a rare earth component X having a maximum solid solubility of ≤0.5 wt % in aluminum. The surface-hardened alloy component has an alloy bulk portion and a hardened alloy surface portion. At least a portion of the hardened alloy surface portion has a Vickers hardness that is at least 30% greater than a Vickers hardness of the alloy bulk portion.

36 MATERIALS SCIENCE↗

Post-processing to Modify the α Phase Micro-Texture and β Phase Grain Morphology in Ti-6Al- 4 V Fabricated by Powder Bed Electron Beam Melting

Additively manufactured Ti-6Al- 4 V has columnar β grains along the build direction with a ⟨001⟩ fiber texture. Due to Burgers Orientation Relationship, the resulting α phase becomes textured albeit less strongly than the β phase. Microtexture zones have been identified in the α phase in laser-based systems. There have been limited studies on α phase texture and its impact on mechanical behavior of Ti-6Al- 4 V fabricated via electron beam melting (EBM) powder bed additive manufacturing along with the use of super-transus heat treatments to modify the resulting α phase texture. We present the role of texture on influencing the tensile behavior of EBM Ti-6Al- 4 V. We observed that super-transus heat treatment of the alloy also results in columnar to equiaxed transition of β grains with a subsequent change in α phase texture. Possible mechanisms for the formation of equiaxed β are reported on.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Electron Beam Melting Technology Improvements

ORNL and Arcam AB have collaborated to improve and broaden the application and dissemination of electron beam melting (EBM) technology. While EBM is a promising additive manufacturing technology with the potential to revolutionize many industries, several issues prevent its widespread adoption at an industrial scale. In collaboration with Arcam, ORNL researchers have worked to improve the reliability of EBM processes using in-situ monitoring methods and data analytics, developed new scan strategies to allow site-specific microstructure control, and expanded EBM technologies to high-temperature materials. This report details the results of this collaboration.

42 ENGINEERING↗

Advanced manufacturing—A transformative enabling capability for fusion

Additive Manufacturing (AM) can create novel and complex engineered material structures. Features such as controlled porosity, micro-fibers and/or nano-particles, transitions in materials and integral robust coatings can be important in developing solutions for fusion subcomponents. A realistic understanding of this capability would be particularly valuable in identifying development paths. Major concerns for using AM processes with lasers or electron beams that melt powder to make refractory parts are the power required and residual stresses arising in fabrication. A related issue is the required combination of lasers or e-beams to continue heating of deposited material (to reduce stresses) and to deposit new material at a reasonable built rate while providing adequate surface finish and resolution for meso-scale features. Some Direct Write processes that can make suitable preforms and be cured to an acceptable density may offer another approach for PFCs.

Additive Manufacturing, fusion energy, Fusion Mate↗

A review on the fatigue behavior of Ti-6Al-4V fabricated by electron beam melting additive manufacturing

Electron beam melting (EBM) is a swiftyly-developing metal additive manufacturing process that holds significant interest in the aerospace and biomedical industries for the high-strength titanium alloy, Ti-6Al-4V. These industries have fatigue-limited applications, yet a lack of understanding of the EBM process-microstructure-fatigue relationships limit widespread use and presents challenges for certification. In this review, uniaxial fatigue data was collected and the effects of build orientation, surface roughness, and hot-isostatic pressing are linked to the fatigue properties highlighting microstructure, defects, and failure mechanisms. The observations and conclusions are supported by statistical analysis using the mean fatigue life obtained by the Statistical Fatigue-Limit Model. Both EBM-process and post-process structure relationships are discussed in order to identify the best-practice for fatigue-resistant design. The performance of the EBM material is compared to conventionally manufactured Ti-6Al-4V and possible methods to increase the fatigue resistance are discussed. Anisotropic fatigue behavior was observed in as-fabricated parts and no statistical distinction was found in the fatigue performance of HIPed and as-fabricated material provided the same as-fabricated rough surface condition. However, comparable fatigue life to traditionally manufactured lamellar Ti-6Al-4V is achieved when both post-process HIP and machining are applied to EBM-fabricated parts.

36 MATERIALS SCIENCE↗

Defects and 3D structural inhomogeneity in electron beam additively manufactured Inconel 718

Highlights: • A protocol for 3D characterization of structure and defects in additively manufactured EBM 718 is presented. • Lack of fusion defects disrupt local microstructure, creating isolated regions of equiaxed grains. • Clustering of micron-scale nitrides is attributed to a particle rafting process. • Normalized size-number density relationship of carbides matches that of industrial ingots. • Removal of porosity via post-processing will not correct microstructural inhomogeneities created by lack of fusion defects. - Abstract: Material structure and defects created during additive manufacturing contribute to the variability in mechanical properties of these parts, limiting their use for critical applications. Three-dimensional crystallographic, structural, and chemical information in electron beam melted Inconel 718 was collected from the sub-micron to the millimeter scale using the TriBeam tomography system. The relationship of defects to the surrounding microstructure has been studied in detail. Lack of fusion defects created sharp discontinuities in the grain morphology that extended several build layers beyond the layer where the defect originated. Nitrides and carbides in the size range of 1.25 μm to 10 μm were observed throughout the volume, with pronounced nitride clustering. The similarities between solidification in additive manufacturing and traditional manufacturing processes are demonstrated by the comparable size and distribution of carbides measured for industrial-scale samples of 718. Defects created during additive manufacturing cannot be easily remedied via standard post-processing techniques, and will likely diminish the mechanical performance of additively manufactured parts.

36 MATERIALS SCIENCE↗

Role of scan strategies on thermal gradient and solidification rate in electron beam powder bed fusion

Local microstructure control in electron beam powder bed fusion (EB-PBF) is of great interest to the additive manufacturing community to realize complex part geometry with targeted performance. The local microstructure control relies on having a detailed understanding of local melt pool physics (e.g., 3-D melt pool shape as well as spatial and temporal variations of thermal gradient (G) and solidification rate (R)). In this research, a new scan strategy referred to as ghost beam is numerically evaluated as a candidate to achieve the targeted G and R of IN718 alloy. The boundary conditions for simulations, including the speed (490 mm/s) and spatial locations of the beam within a given layer, are obtained by using series of snapshot images, recorded at 12,000 frames per second, using a high-speed camera. The heat transfer simulations were performed using TRUCHAS an open-source software deployed within a high-performance computational infrastructure. The simulation results showed that reheating at short beam on-time and time delay decreases both G and R. Local variation of R at the center of the melt pool trailing edge showed periodic temporal fluctuations. Finally, the ghost beam scan strategy was compared to other existing raster and spot scan strategies.

36 MATERIALS SCIENCE↗

Correlations Between Powder Feedstock Quality, In Situ Porosity Detection, and Fatigue Behavior of Ti-6Al-4V Fabricated by Powder Bed Electron Beam Melting: A Step Towards Qualification

Ti-6Al-4V is the most studied alloy via electron beam melting (EBM) with regards to microstructure and mechanical behavior, but there have been no attempts to correlate in situ porosity detection and fatigue behavior. This is required for widespread adoption of EBM because conventional evaluation is often time-consuming and expensive. This study presents the use of near-infrared imaging to detect and quantify porosity in Ti-6Al-4V builds fabricated from different powder feedstocks and its correlation to their fatigue response. Finally, we report that, for identical processing parameters, the variability in powder feedstock causes variations in porosity and scatter in the respective fatigue response.

36 MATERIALS SCIENCE↗

Asymmetric Cracking in Mar-M247 Alloy Builds During Electron Beam Powder Bed Fusion Additive Manufacturing

In the electron beam powder bed fusion (EB-PBF) process, a substantial number of high-gamma prime Ni-based superalloys are considered as non-printable due to a high propensity to form cracks. In this research, we focused on computational modeling framework to predict solidification-related cracking phenomena in EB-PBF processes. The cracking analysis was performed on cylindrical overhang structures where the cracks are observed only on one side of the part. Comprehensive microstructural characterization correlated the cracking tendency to low-melting point liquid-film formation along columnar grain boundaries with high misorientation angles due to partitioning of alloying elements. Uncoupled numerical thermal and mechanical models were used to rationalize the relationship between process parameters, build geometry, and cracking. The simulations showed asymmetric temperature distributions and associated asymmetric tensile thermal stresses over a cross section due to differences in section modulus and periodic changes in beam scanning directions. Here, the results provide a potential pathway based on spatially varying beam scanning strategies to reduce the cracking tendency during additive manufacturing of complex geometries on the overhang structure in high-gamma prime nickel-based superalloys.

36 MATERIALS SCIENCE↗

Additive Manufacturing of Nickel Superalloys: Opportunities for Innovation and Challenges Related to Qualification

Innovative designs for turbines can be achieved by advances in nickel-based superalloys and manufacturing methods, including the adoption of additive manufacturing. In this regard, selective electron beam melting (SEBM) and selective laser melting (SLM) of nickel-based superalloys do provide distinct advantages. Furthermore, the direct energy deposition (DED) processes can be used for repair and reclamation of nickel alloy components. The current paper explores opportunities for innovation and qualification challenges with respect to deployment of AM as a disruptive manufacturing technology. Here in the first part of the paper, fundamental correlations of processing parameters to defect tendency and microstructure evolution will be explored using DED process. In the second part of the paper, opportunities for innovation in terms of site-specific control of microstructure during processing will be discussed. In the third part of the paper, challenges in qualification of AM parts for service will be discussed and potential methods to alleviate these issues through in situ process monitoring, and big data analytics are proposed.

36 MATERIALS SCIENCE↗

Understanding Part to Part Variability During Directed Energy Deposition Processes Using In Situ and Ex Situ Process Characterization

The overall goal of this technical collaboration is the use of in situ and ex situ characterization techniques to understand part to part variability in Ti-6Al-4V parts fabricated using directed energy deposition (DED) process, and subsequently qualify parts fabricated using AM. The primary goal of the Phase-1 of this CRADA was to demonstrate the feasibility of capturing the above changes using a combination of high speed stereo imaging and in situ monitoring using two wavelength pyrometers. The in situ monitoring was then correlated using ex situ characterization performed using optical microscopy. The results from phase-1 clearly show that changes to the process and shielding gases have a significant impact on the geometric conformity of the build and the build layer height. The results from phase-1 show that in addition to using IR thermography as a tool to measure the temperature and gradients, we could use it to monitor the build topography and the layer height and use the information to develop closed loop control systems. The phase-1 results show that there is a narrow zone under which the process must operate in order to be “passively stable” or autocorrect for over building. In addition, the results demonstrate that when operated within this range the build autocorrects and there is a drastic reduction in the interlayer lack of fusion defect formation.

36 MATERIALS SCIENCE↗

Controlling microstructure in deposits fabricated using powder blown direct energy deposition technique

The overall goal of this collaboration is to develop technologies to control grain morphology and microstructures of Inconel 718 components additively manufactured through the Direct Energy Deposition (DED) process (Identical to the LENS (laser engineered net shaping) processes) and to achieve equiaxed or near equiaxed grain structures. The phase1 technical collaboration was used to fabricate Inconel 718 builds with different process parameters, pre heat and scan strategies. The results were then rationalized using computational heat transfer and solidification models. Microstructural characterization showed that the aspect ratio of the grains can be reduced to less than 1.5, and that control of the grain sizes to within 50-100 μm could be potentially obtained by using an external source to preheat the substrate to 400 ̊C. Heat transfer models coupled with solidification models were used to rationalize the results which show that preheating lowered the temperature gradient thereby resulting in moving towards the equiaxed region of the columnar to equiaxed transition (CET) curve. The results demonstrate that higher preheat temperatures could be potentially used to obtain a truly equiaxed structure.

36 MATERIALS SCIENCE↗

Applying neutron transmission physics and 3D statistical full-field model to understand 2D Bragg-edge imaging

Bragg-edge imaging, which is also known as neutron radiography, has recently emerged as a novel crystalline characterization technique. Modelling of this novel technique by incorporating various features of the underlying microstructure (including the crystallographic texture, the morphological texture, and the grain size) of the material remains a subject of considerable research and development. In this paper, Inconel 718 samples made by additive manufacturing were investigated by neutron diffraction and neutron radiography techniques. The specimen features strong morphological and crystallographic textures and a highly heterogeneous microstructure. A 3D statistical full-field model is introduced by taking details of the microstructure into account to understand the experimental neutron radiography results. The Bragg-edge imaging and the total cross section were calculated based on the neutron transmission physics. A good match was obtained between the model predictions and experimental results at different incident beam angles with respect to the sample build direction. The current theoretical approach has the ability to incorporate 3D spatially resolved microstructural heterogeneity information and shows promise in understanding the 2D neutron radiography of bulk samples. With further development to incorporate the heterogeneity in lattice strain in the model, it can be used as a powerful tool in the future to better understand the neutron radiography data.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Optimizing Parameters for Post-Processing of Ti-6Al-4V Components Fabricated by Additive Manufacturing for Superior Performance

ORNL worked with Quintus Technologies to develop new hot isostatic pressing parameters for Ti-6Al-4V components fabricated via Arcam electron beam melting. These parameters result in isotropic tensile behavior compared to the conventional hot isostatic press HIP parameters that result in anisotropic tensile properties depending on the build direction. Furthermore, an improvement in fatigue behavior was observed.

42 ENGINEERING↗

Characterization of Crystallographic Structures Using Bragg-Edge Neutron Imaging at the Spallation Neutron Source

Over the past decade, wavelength-dependent neutron radiography, also known as Bragg-edge imaging, has been employed as a non-destructive bulk characterization method due to its sensitivity to coherent elastic neutron scattering that is associated with crystalline structures. Several analysis approaches have been developed to quantitatively determine crystalline orientation, lattice strain, and phase distribution. In this study, we report a systematic investigation of the crystal structures of metallic materials (such as selected textureless powder samples and additively manufactured (AM) Inconel 718 samples), using Bragg-edge imaging at the Oak Ridge National Laboratory (ORNL) Spallation Neutron Source (SNS). Firstly, we have implemented a phenomenological Gaussian-based fitting in a Python-based computer called iBeatles. Secondly, we have developed a model-based approach to analyze Bragg-edge transmission spectra, which allows quantitative determination of the crystallographic attributes. Moreover, neutron diffraction measurements were carried out to validate the Bragg-edge analytical methods. These results demonstrate that the microstructural complexity (in this case, texture) plays a key role in determining the crystallographic parameters (lattice constant or interplanar spacing), which implies that the Bragg-edge image analysis methods must be carefully selected based on the material structures.

47 OTHER INSTRUMENTATION↗

Characterization of topology optimized Ti-6Al-4V components using electron beam powder bed fusion

The use of manufacturing to generate topology optimized components shows promise for designers. However, designers who assume that additive manufacturing follows traditional manufacturing techniques may be misled due to the nuances in specific techniques. Since commercial topology optimization software tools are neither designed to consider orientation of the parts nor large variations in properties, the goal of this research is to evaluate the limitations of an existing commercial topology optimization software (i.e. Inspire®) using electron beam powder bed fusion (i.e. Arcam®) to produce optimized Ti-6Al-4V alloy components. Emerging qualification tools from Oak Ridge National Laboratory including in-situ near-infrared imaging and log file data analysis were used to rationalize the final performance of components. While the weight savings of each optimized part exceeded the initial criteria, the failure loads and locations proved instrumental in providing insight to additive manufacturing with topology optimization. In conclusion, this research has shown the need for a comprehensive understanding of correlations between geometry, additive manufacturing processing conditions, defect generation, and microstructure for characterization of complex components such as those designed by topology optimization.

42 ENGINEERING↗