Search NASA⌕ Search

Engineering topics

Dehoff, Ryan

Publications and source records attributed to Dehoff, Ryan.

At least 37 records · Page 2

Process Capability Study on the Volume Manufacturing of a Complex Rotating Automotive Component in Laser Powder Bed Fusion Additive Manufacturing

Oak Ridge National Lab (ORNL) and Ford Motor Company used an AddUp FormUp 350 to print a turbo wheel geometry to show feasibility of laser powder bed fusion (L-PBF) additive manufacturing (AM) in producing cost-effective components for automotive industries. L-PBF AM has potential to disrupt traditional manufacturing techniques by introducing novel materials and geometries that cannot otherwise be produced. Fundamental challenges associated with L-PBF include limitations on printing overhang geometries and resulting surface finish. In this collaboration, ORNL and Ford partnered with AddUp to show the viability of using L-PBF for an AM design turbine wheel while reducing as-fabricated surface roughness. A cost model associated with mass production was produced to analyze benefits of pursing LPBF AM compared to investment casting.

36 MATERIALS SCIENCE↗

Heterogeneous phase transformation pathways in additively manufactured Al-Ce-Mn alloys

Heat treatment of additively manufactured Al-Ce based multicomponent alloys leads to complex microstructure evolution. In this research, the ability to extend the phase transformation theories involving nucleation of a product phase from a heterogeneous multi-phase microstructure typical to that of additively manufactured samples is explored. The Al-10Ce-8Mn (wt%) was used as a model alloy system. Under additive manufacturing conditions different solidification microstructures were obtained due to spatial and temporal variations of thermal gradients (G) and liquid-solid interface velocities (R) within a given melt pool. Near the melt pool boundary (high G and low R, referred as MPB region), initially, Al 20 Mn 2 Ce forms from the liquid followed by a eutectic of FCC Al and Al 11 Ce 3 . In the melt pool interiors (low G and high R referred as ES region) a eutectic structure between FCC Al and Al 20 Mn 2 Ce is observed. During subsequent heat treatments, the MPB and ES regions transform into different sets of microstructures. In the MPB region, a fine globular microstructure containing FCC Al, Al 11 Ce 3 , Al 6 Mn, and Al 12 Mn results from the decomposition of Al 20 Mn 2 Ce. In the ES region a faceted Al 51 Mn 7 Ce 4 plate phase results from the decomposition of Al 20 Mn 2 Ce. The formation of the Al 51 Mn 7 Ce 4 phase within the eutectic microstructure at the boundaries of FCC Al and Al 20 Mn 2 Ce has not been reported in the literature. Further, these two distinct phase transformation pathways are rationalized based on the role of driving force on the nucleation of (Al 6 Mn) and/or metastable intermetallic (Al 51 Mn 7 Ce 4 ) phases at the interface of aluminum (FCC) and the non-equilibrium intermetallic (Al 20 Mn 2 Ce) phases.

36 MATERIALS SCIENCE↗

Evaluation of AddUp Precision L-PBF Technology for Tooling and Other Industrial Applications

ORNL (Contractor) and AddUp Inc. (Participant) collaborated to enable the adoption of laser powder bed fusion for tooling applications, critical for reshoring the manufacturing sector in the U.S. Most of the work on laser powder bed fusion has focused on high value materials such as Ti-6Al-4V and Inconel 718 for niche applications in aerospace, biomedical and energy sectors. In this collaboration, ORNL and AddUp worked laser powder bed fusion of maraging steels for tooling applications while leveraging the unique ability of the AddUp laser powder bed fusion system to deposit fine powders. We demonstrated that the AddUp technology is capable of depositing complex artifacts and features such as overhangs within desired tolerances. We also showed that direct aging of the deposited parts result in simultaneously higher strength and elongation compared to the conventional two step heat treatments, which could result in significant energy savings. Finally, we developed thermos-kinetic models to enable design of heat treatments for optimal material properties compared to the energy intensive empirical methods currently used. The report summarizes the detailed findings of this collaboration.

36 MATERIALS SCIENCE↗

Simurgh: A Framework for Cad-Driven Deep Learning Based X-Ray CT Reconstruction

High-resolution X-ray computed tomography (XCT) is an important technique for the inspection of additively manufactured (AM) parts. While XCT is typically used off-line to inspect a subset of manufactured parts, significantly accelerating measurement speed while retaining accuracy would enable use of XCT for in-line inspection to rapidly identify defects in each part as it is manufactured. Here, we propose a deep learning (DL) based approach that uses computer aided design (CAD) models of the AM parts and physics-based information to rapidly produce high-quality reconstructions from sparse XCT measurements without high quality ground truth data. Our approach uses a generative adversarial neural network (GAN) to produced realistic training data from the CAD-based simulations and a deep neural network that is trained using data from the first stage to produce accurate 3D reconstructions. Using experimental XCT data of metal parts, we demonstrate enhanced defect detection capabilities while dramatically reducing the scan time.

Ziabari, Amir↗

Advancement of Certification Methods and Applications for Industrial Deployments of Components Derived from Advanced Manufacturing Technologies

One goal of the Advanced Materials and Manufacturing Technologies subprogram, within the Department of Energy’s (DOE) crosscutting technology development program, is to advance the qualification and certification of parts and components created via additive manufacturing (AM). AM offers a new paradigm for the design and optimization of new nuclear components, and for observing and tracking manufacturing performance and potential defects in a way that is not possible with traditional approaches. Tracking and evaluating these in situ data can lead to the estimation of local material properties and, with the use of engineering analysis tools, the estimation of component performance during operation. To achieve these objectives, a digital platform certification approach was developed and is summarized in this report.

36 MATERIALS SCIENCE↗

Phase stability in cast and additively manufactured Al-rich Al-Cu-Ce alloys

Additively manufactured (AM) eutectic Al alloy systems have been studied extensively for advantageous thermal stability and mechanical properties due to their refined microstructures. Al-Cu-Ce alloys are one subset of these AM eutectic alloys. Here we studied phase stability in AM Al-Cu-Ce alloys and compared it to that of conventionally cast ones. A new phase, Al 8 Cu 3 Ce, was identified in the microstructures of both AM and cast Al-Cu-Ce alloys. This Al 8 Cu 3 Ce phase was not previously included on experimental or thermodynamically calculated phase diagrams of the Al-Cu-Ce system. Therefore, we performed additional thermodynamic modeling of the system. These models were experimentally validated with cast and subsequently heat-treated Al-Cu-Ce alloys. We found that despite the refined microstructure of the AM alloys, the phases formed were consistent with the cast alloys, suggesting that AM processing did not significantly alter the formation and stability of phases from that in the conventional alloys. In conclusion, this work has resolved inconsistent previous descriptions of the Al-Cu-Ce ternary phase diagram in the Al-rich region and resulted in the addition of the Al 8 Cu 3 Ce as an equilibrium phase above 500 °C.

36 MATERIALS SCIENCE↗

Data Mining and Visualization of High-Dimensional ICME Data for Additive Manufacturing

Integrated computational materials engineering (ICME) methods combining CALPHAD with process-based simulations can produce rich, high-dimensional data for alloy and process design. In ICME methods for metallurgical applications, the visualization and interpretation of such high-dimensional data has previously been through heat maps represented in 2 or 3 dimensions. While such an approach is ideal when one variable is varied at a time, in the case of high-dimensional data with multiple variables varied simultaneously, as is the case in additive manufacturing, interpreting the trends through two- or three-dimensional heat maps becomes challenging. Here, we propose a strategy of mixed visual data mining and quantitative analysis for high-dimensional metallurgical and process data using high-throughput thermodynamic calculations. Two case studies show the application of the proposed approach. The first case study investigated the effects of feedstock chemistry on the δ ferrite formation in 316L stainless steel powders used for binder jet additive manufacturing. The second case study linked Scheil–Gulliver calculations to a process model for dissimilar joining of aluminum alloys 5356 and 6111 during laser hot-wire additive manufacturing. Both cases contained thousands of calculated data points, showcasing the utility of visual data analysis through parallel coordinate plotting, Pearson correlation coefficient matrices, and scatter matrices compared to traditional process maps. These visualization techniques can be extended to many additive manufacturing problems to capture process–structure–property relationships for additively manufactured components.

36 MATERIALS SCIENCE↗

Role of scan strategies and heat treatment on grain structure evolution in Fe-Si soft magnetic alloys made by laser-powder bed fusion

A major goal in printing soft magnetic Fe-Si steels using additive manufacturing is to take advantage of the potential for complex geometric designs and site-specific grain control. One major step in the processing of these alloys is understanding how processing parameters might impact how the as-built microstructure responds to annealing (i.e. the annealing response). The impact of scan strategy on the annealing response for thin wall geometries is specifically explored. Two scan strategies were explored for a thin wall geometry that produced a strongly columnar grain structure and equiaxed grain structure. Additionally, samples from both scan strategies annealed at 1200 °C showed a marked difference in annealing response with the more equiaxed sample seeing full recrystallization and grain growth, while the more columnar grain structure saw little change in microstructure. After analysis through characterization techniques and thermal-mechanical simulations Differences in internal energy within the grains were ruled out because calculated GND density values were similar for both samples. The formation of secondary particles was ruled out as a contributing factor due to the type of oxide formations and their size. It was concluded that the contributing factor to the difference in the annealing response were a difference in the resulting grain size and the density of high angle grain boundaries. These two differences were largely attributed to differences in the thermal gradient conditions due to grains preferentially growing in the direction of the steepest thermal gradient.

36 MATERIALS SCIENCE↗

Localized Defect Detection from Spatially Mapped, In-Situ Process Data With Machine Learning

In powder bed fusion additive manufacturing, machines are often equipped with in-situ sensors to monitor the build environment as well as machine actuators and subsystems. The data from these sensors offer rich information about the consistency of the fabrication process within a build and across builds. This information may be used for process monitoring and defect detection; however, little has been done to leverage this data from the machines for more than just coarse-grained process monitoring. In this work we demonstrate how these inherently temporal data may be mapped spatially by leveraging scan path information. We then train a XGBoost machine learning model to predict localized defects—specifically soot–using only the mapped process data of builds from a laser powder bed fusion process as input features. The XGBoost model offers a feature importance metric that will help to elucidate possible relationships between the process data and observed defects. Finally, we analyze the model performance spatially and rationalize areas of greater and lesser performance.

3D printing↗

Elevated temperature ductility dip in an additively manufactured Al-Cu-Ce alloy

The deformation and failure mechanisms of Al-9Cu-6Ce (wt%) based alloys fabricated with laser powder bed fusion were investigated from room temperature to 400°C. The yield and ultimate tensile strengths decreased monotonically with increase in temperature, but the tensile elongation dipped unexpectedly at elevated temperatures and exhibited a minimum at 300°C. The dip in tensile elongation occurred with a concomitant dip in strain-rate sensitivity (SRS) of deformation. The as-fabricated alloy microstructure was heterogeneous, and the heat affected zone (HAZ) underneath the melt pool boundary was prone to strain localization. At 300 °C, the reduced SRS promoted the progression of strain localization in the HAZ leading to failure initiation and the dip in tensile elongation. Furthermore, a higher SRS or strain-hardening rate at other temperatures improved the tensile elongation by slowing the progression of strain localization in the HAZ such that failure initiated by other mechanisms elsewhere in the microstructure. Notably, the tensile elongation was limited by the defect structure only in a narrow temperature range (150 - 200 °C) while at other temperatures it was limited by the inherent microstructural features. This investigation exemplifies unexpected deformation and failure mechanisms possible in heterogeneous microstructures that result from additive manufacturing.

36 MATERIALS SCIENCE↗

Microstructure and properties of additively manufactured Al–Ce–Mg alloys

Additive manufacturing of aluminum alloys is largely dominated by a near-eutectic Al-Si compositions, which are highly weldable, but have mechanical properties that are not competitive with conventional wrought Al alloys. In addition, there is a need for new Al alloys with improved high temperature properties and thermal stability for applications in the automotive and aerospace fields. In this work, we considered laser powder bed fusion additive manufacturing of two alloys in the Al–Ce–Mg system, designed as near-eutectic (Al–11Ce–7Mg) and hyper-eutectic (Al–15Ce–9Mg) compositions with respect to the binary L → Al + Al 11 Ce eutectic reaction. The addition of magnesium is used to promote solid solution strengthening. A custom laser scan pattern was used to reduce the formation of keyhole porosity, which was caused by excessive vaporization due to the high vapor pressure of magnesium. The microstructure and tensile mechanical properties of the alloys were characterized in the as-fabricated condition and following hot isostatic pressing. The two alloys exhibit significant variations in solidification structure morphology. These variations in non-equilibrium solidification structure were rationalized using a combination of thermodynamic and thermal modeling. Both alloys showed higher yield strength than AM Al-10Si-Mg for temperatures up to 350 °C and better strength retention at elevated temperatures than additively manufactured Scalmaloy.

36 MATERIALS SCIENCE↗

In-situ digital image correlation and thermal monitoring in directed energy deposition additive manufacturing

As in welding, directed energy deposition (DED) additive manufacturing (AM) generates complex residual stresses and distortions commensurate with the complexity of the scan pattern used for deposition. To date, measuring DED distortions on complex geometries has only been achieved post process, discarding the complex thermomechanical history that leads to that final material state. In this work, surround stereo digital image correlation (DIC) is used to 3D map surfaces and strain tensors in-situ in a powder-blown laser DED system. Infrared thermography is then projected onto these surfaces to record the full thermomechanical history of printed parts. DIC presents a unique challenge to DED AM, as no part exists at the beginning of deposition, which (a) prevents application of an appropriate speckle pattern and (b) denies the user a zero strain reference frame. Solutions to these problems are proposed and their limitations explored herein. In sum, this work presents a relatively low-cost solution to monitoring and optimizing the unique temporal artifacts induced by complex scan strategies that was previously unobtainable.

42 ENGINEERING↗

Beam Hardening Artifact Reduction in X-Ray CT Reconstruction of 3D Printed Metal Parts Leveraging Deep Learning and CAD Models

Nondestructive evaluation (NDE) of additively manufactured (AM) parts is important for understanding the impacts of various process parameters and qualifying the built part. X-ray computed tomography (XCT) has played a critical role in rapid NDE and characterization of AM parts. However, XCT of metal AM parts can be challenging because of artifacts produced by standard reconstruction algorithms as a result of a confounding effect called “beam hardening.” Beam hardening artifacts complicate the analysis of XCT images and adversely impact the process of detecting defects, such as pores and cracks, which is key to ensuring the quality of the parts being printed. In this work, we propose a novel framework based on using available computer-aided design (CAD) models for parts to be manufactured, accurate XCT simulations, and a deep-neural network to produce high-quality XCT reconstructions from data that are affected by noise and beam hardening. Using extensive experiments with simulated data sets, we demonstrate that our method can significantly improve the reconstruction quality, thereby enabling better detection of defects compared with the state of the art. We also present promising preliminary results of applying the deep networks trained using CAD models to experimental data obtained from XCT of an AM jet-engine turbine blade.

Ziabari, Amir↗